Digital Commons Network^™

Synergetic Effect Of Viscosity Modifying Admixtures And Polycarboxylate Ether Superplasticizer On Key Characteristics Of Thixotropic Uhpc For Bonded Bridge Deck Overlay Rehabilitation, Le Teng, Ming Jin, Jiadi Du, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Thin bonded ultra-high-performance concrete (UHPC) overlay is an advanced technology for bridge deck rehabilitation. UHPC should be tailored to secure adequate flowability and high thixotropy to facilitate mixing and placement with a low risk of sagging of the material on sloped bridge deck surfaces. The synergetic effect between nano clay (NC) and polycarboxylate ether (PCE) superplasticizer or cellulose-based viscosity modifying admixture (VMA) and PCE on the rheological properties (yield stress, plastic viscosity, and thixotropy), cement hydration, autogenous shrinkage, compressive strength, and porosity was systematically investigated. The bond strength between conventional concrete (CC) representing existing bridge deck concrete and thixotropic UHPC …

Laboratory Evaluation And Field Demonstration Of Cold In-Place Recycling Asphalt Mixture In Michigan Low-Volume Road, Dongzhao Jin, Lei Yin, Lance Malburg, Zhanping You

Michigan Tech Publications, Part 2

Cold-in place recycling (CIR) is a promising technology for the rehabilitation of asphalt pavements. However, the CIR asphalt pavement constructed in the field often has high air voids due to the presence of moisture during construction, and the moisture susceptibility of the pavement is crucial in determining its service life. Therefore, the objective of this research was to assess the laboratory performance of CIR asphalt mixes under freeze-thaw conditions (The mix prior to being subjected to freezing and thawing is labeled as "dry condition", while the mix that was placed in a refrigerator at –18 °C for 16 h and …

Understanding The Impact Of Microplastic Contamination On Soil Quality And Eco-Toxicological Risks In Horticulture: A Comprehensive Review, N. P. Gayathri, Geena Prasad, Vaishna Prabhakaran, Vishnu Priya

Research outputs 2022 to 2026

The horticulture sector, essential for global food production, confronts significant challenges with prevalent pollutants, mainly microplastics. The presence of microplastics in the food chain has induced physiological stress and a multifactorial food safety concern. The complexity of the problem, arising from intricate interactions among microplastics, organisms, and ecosystems, poses a substantial challenge to food safety, necessitating an immediate strategic perspective due to the associated risks to human health and eco-toxicology. Significant knowledge gaps persist regarding their impact on terrestrial ecosystems, especially in horticulture. This study addresses the urgent need to comprehend the implications of microplastics on soil health, eco-toxicological risks, …

Application Of Multidisciplinary Community Resilience Modeling To Reduce Disaster Risk: Building Back Better, Wanting "Lisa" Wang, John W. Van De Lindt, Blythe Johnston, P. Shane Crawford, Guirong Grace Yan, Thang Dao, Trung Do, Katie Skakel, Mojtaba Harati, Tu Nguyen, Robinson Umeike, Silvana Croope, Andre R. Barbosa

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

From december 10 to december 11, 2021, a deadly tornado outbreak struck across several states in the us, including arkansas, illinois, kentucky, and tennessee. This tornado outbreak resulted in at least $3.9 Billion in damage, more than 90 fatalities, and hundreds of injuries. Mayfield, kentucky, a small city in the eastern united states, was hit by a long-track tornado rated as an enhanced fujita 4 (ef4) scale and was one of the communities most heavily damaged during the tornado outbreak. Following the 2021 tornado event, an analysis was performed in the interdependent networked community resilience modeling environment (in-core) for the …

Chloride Binding Mechanism In Seawater-Mixed Uhpc, Wei Zhang, Dawei Ding, Mengmeng Li, Tiao Wang, Hongyan Ma, Binmeng Chen, Hongxing Hu, Jizhou Chen, Xiaomin Liu, Dongshuai Hou

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The rapid development of marine concrete structures and the sharp shortage of freshwater resources contribute to the wide investigation of seawater-mixed ultra-high-performance concrete (swuhpc). However, few studies have investigated the chloride ions (cl-) binding mechanism of swuhpc. Herein, the chloride binding experiments and molecular dynamics (md) simulation were carried out to reveal the physically and chemically bound cl- mechanisms of swuhpc. The results of the experiments clearly demonstrate that the addition of silica fume (sf) led to a significant decrease in the capacity of cl- binding. Conversely, the incorporation of metakaolin (mk) resulted in a marked increase in the content …

Effect Of Waste Covid-19 Masks On Compaction Characteristics Of Silty-Clay Soil, Sydney K. Lawson

Honors College Theses

The present study aims to explore the effect of adding shredded waste Covid-19 masks to silty-clay soil on the soil’s compaction characteristics for beneficial use in embankment, the subgrade of roadways, or backfill. This was accomplished by using two different types of masks: blue surgical masks and KN95 masks. Both mask types were hand shredded into half-inch sections using safety-scissors. The maximum dry density (MDD) and optimum moisture content (OMC) are the two most important compaction characteristics, and they were determined by the Standard Proctor Compaction Test (ASTM D698 / AASHTO T99). The change of both the MDD and OMC …

Physical And Stochiometric Controls On Nutrient Uptake And Ecosystem Respiration In Contrasting Sites, Jancoba K. Dorley

Civil Engineering ETDs

Meteorological, hydrological, and biogeochemical processes naturally control stream ecosystems. These processes define the frequency and distribution of precipitation and the supply and demand of solutes and particles to support aquatic food chains through space and time. Studies have also found that stream ecosystems are also controlled by anthropogenic activities, which occur on a much shorter timescale. These anthropogenic activities affect stream ecosystems' structure and function from local to planetary changes to the environment. It is essential for scientists and engineers to understand the relationships between naturally occurring processes and those created by human activities for a better interpretation of stream …

Determining The Impacts Of Corn Silage Mixing Ratios On Hydrogen Production From Beef Cattle Manure, Katya Faber-Quimby

Honors Theses

With global warming becoming an increasingly serious threat and a growing population requiring additional energy resources, interest in the production of clean energy from the agricultural sector has surged in popularity. Biohydrogen, also known as green hydrogen, is H₂ that has been produced using renewable energy, such as from agricultural byproducts or waste materials. It presents a promising alternative to nonrenewable resources due to its high potential for energy storage and lack of carbon emissions when used. Cattle manure has been explored as a resource for the production of biohydrogen. Selecting for hydrogen-producing microbes in the manure serves the …

A Review Of Whipple Shield Ballistic Limit Equations, S. Ryan, W. (William) P. Schonberg

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Ballistic limit equations (BLEs) are semi-analytical expressions used to predict the risk posed by micrometeoroid and orbital debris (MMOD) impacts on a spacecraft. A foundational BLE, known as the new non-optimum (NNO) equation was published by Eric Christiansen of NASA Johnson Space Center in 1990 for application on Whipple shields – two-plate configurations consisting of a thin sacrificial plate located at some standoff in front of the spacecraft pressure hull or structural wall. Today, BLEs for almost all multi-plate spacecraft structures, e.g., honeycomb sandwich panels, monolithic structures with thermal insulation blankets, etc., are based on the NNO Whipple BLE. We …

Four-Way Cfd-Dem Coupling To Simulate Concrete Pipe Flow: Mechanism Of Formation Of Lubrication Layer, Tooran Tavangar, Masoud Hosseinpoor, Jeffrey S. Marshall, Ammar Yahia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study introduced a four-way CFD-DEM coupling approach to simulate the shear-induced particle migration (SIPM) mechanism leading to formation of the lubrication layer (LL) during concrete pumping. The CFD-DEM simulations considered the coupled effect of concentration (10 %–40 %) and wide size distribution (1–17 mm) of aggregate and rheology of the mortar for forces between the suspending matrix and the particles (and vice versa), as well as force transmission directly between particles (and the pipe wall). The formation of the LL was successfully simulated through a more realistic understanding the SIPM mechanism and rheological evaluation across the pipe with comparable …

To What Extent Do Water Reuse Treatments Reduce Antibiotic Resistance Indicators? A Comparison Of Two Full-Scale Systems, Ishi Keenum, Jeanette Calarco, Haniyyah Majeed, E. Eldridge Hager-Soto, Charles Bott, Emily Garner, Valerie J. Harwood, Amy Pruden

Michigan Tech Publications, Part 2

Water reuse is an essential strategy for reducing water demand from conventional sources, alleviating water stress, and promoting sustainability, but understanding the effectiveness of associated treatment processes as barriers to the spread of antibiotic resistance is an important consideration to protecting human health. We comprehensively evaluated the reduction of antibiotic resistance genes (ARGs) and antibiotic-resistant bacteria (ARB) in two field-operational water reuse systems with distinct treatment trains, one producing water for indirect potable reuse (ozone/biologically-active carbon/granular activated carbon) and the other for non-potable reuse (denitrification-filtration/chlorination) using metagenomic sequencing and culture. Relative abundances of total ARGs/clinically-relevant ARGs and cultured ARB were …

Modeling Inflation Transmission Among Different Construction Materials, Mohamad Abdul Nabi, Islam H. El-Adaway, Rayan H. Assaad

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Cost estimating in the construction industry is challenging due to the high uncertainty associated with the supply chain, especially after the COVID-19 pandemic. Some research studies have addressed such problems by developing models that predict material cost. In fact, all material can be interconnected and interrelated with lead-lag relationships such that any inflation in one material's price can be associated with inflation in other materials' prices, referred to as transmission of inflation. Despite the latter, none of the existing studies have investigated inflation transmission among all construction materials. This paper fills this knowledge gap. The authors used a multistep research …

Investigating Causes Of Disputes Resulting In Litigation In Airport Development Projects In The United States Using Graph-Based Techniques, Ramy Khalef, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Airports represent a crucial a sector of the US infrastructure, but they were documented to have scored a D+. To mitigate this, governmental authorities have issued initiatives to update the airport infrastructure. With an expected critical junction for a major transformation in the airport sector, it is anticipated that airport projects will increase. This shall result in an escalation in the number of disputes. Previous research analyzed dispute concerns within the construction sector, but none tackled the perspective of airport projects. Accordingly, the goal of this study is to investigate the leading causes of disputes in litigation within US airport …

Investigation Into The Effect Of Mixture Composition On Setting Time Of Magnesium Phosphate Cement, Autumn Broglen

Civil Engineering Undergraduate Honors Theses

Magnesium phosphate cement (MPC) is a cementitious material that is formed through an acid-base reaction between magnesia and phosphate. This reaction occurs rapidly, making MPC an appealing choice for rapid repair applications. The purpose of this project is to investigate the impact of different proportions of class F fly ash, set retarder consisting of a mixture of boric acid and dextrose, magnesium to phosphate ratio, and water/cement ratio on the initial setting time of MPC paste. Different mixtures of MPC paste were developed to vary the proportions of each constituent, and setting time of each mixture was determined using the …

Exploring The Role Of Near Channel Geospatial Attributes To Predict Suspended Sediment Concentration Patterns Across The Conus Region, Aaron J. Sigman

All Graduate Theses and Dissertations, Fall 2023 to Present

High concentrations of suspended sediment (SSC) in a river can represent a critical water quality concern, reduce the storage capacity of reservoirs, and impact aquatic habitat. The total amount of sediment is calculated from a combination of river properties, including the amount of available sediment and the flow of water carrying the sediment. Water flow properties can be found using local information about the channel, however understanding the concentration of sediment in the river requires understanding the supply of sediment from the watershed. To understand where sediment is coming from, we examined over 1000 United States Geological Survey sites with …

Field Flow Measurements For Pipe Installations With Non-Ideal Conditions, Jake Douglas

All Graduate Theses and Dissertations, Fall 2023 to Present

Accurate flow measurement data is necessary to effectively manage water resources. The purpose of this research is to investigate options to improve field flow measurement by investigating alternatives for calibrating flow meters installed in non-ideal piping. Typically, to accurately measure a flow rate using most types of flow meters, it is recommended that a straight section of pipe be installed immediately upstream and downstream of the flow meter to avoid flow fluctuations at the meter location. However, in many cases, flow disturbances upstream of the meter are unavoidable.

The performance of field flow measurements in non-ideal piping scenarios were studied …

Tracking Perfluoroalkyl Substances From Wastewater Influent To Its Accumulation In Vegetables And Forage Grass, Simon Kozik

All Graduate Theses and Dissertations, Fall 2023 to Present

Per and poly-fluorinated alkyl substances (PFAS) are a class of chemicals that are persistent in the environment. PFAS was found in wastewater, which can be used after wastewater treatment for irrigation water, and in the biosolids that can be mixed with soils to provide nutrients and generally improve soil quality. This study found when wastewater was used it increases the level of PFAS in vegetables and forage grass. PFAS concentrations were tracked from the influent of the wastewater treatment plant to the effluent, to the irrigation water, to the soil, and finally into the vegetable and forage grass grown on …

Water Data Science: Data Driven Techniques, Training, And Tools For Improved Management Of High Frequency Water Resources Data, Amber Spackman Jones

All Graduate Theses and Dissertations, Fall 2023 to Present

Electronic sensors can measure water and climate conditions at high frequency and generate large quantities of observed data. This work addresses data management challenges associated with the volume and complexity of high frequency water data. We developed techniques for automatically reviewing data, created materials for training water data managers, and explored existing and emerging technologies for sensor data management.

Data collected by sensors often include errors due to sensor failure or environmental conditions that need to be removed, labeled, or corrected before the data can be used for analysis. Manual review and correction of these data can be tedious and …

Advancing Near Surface Soil Moisture Measurements Using Robotics, Automation, And Remote Sensing, Hemanth Narayan Dakshinamurthy

All Graduate Theses and Dissertations, Fall 2023 to Present

Near-surface soil moisture, or the water content within the soil, is important for understanding the interactions between land and the atmosphere, and for monitoring plants in agricultural settings. However, soil moisture can be highly variable within the same field and varies considerably with time. The challenge involved with measuring soil moisture is that traditional techniques that rely on obtaining large samples are labor and time-intensive, especially for large fields. Developments in sensor technologies have allowed users to record the soil moisture regularly at the points where the sensors are installed. However, to understand how soil moisture changes across a field …

Poster Session: Onu Engineering Freshman And Senior Design Projects, Keith Schimmel

Scholar Week 2016 - present

This poster session is held Friday, April 19, 4:45-6:15pm, with food served, in the Reed Hall of Science Tech Center.

The capstone engineering senior design projects at Olivet Nazarene University involve interdisciplinary engineering teams completing real-life projects sponsored by companies, mission organizations, and professional society competitions. The engineering first-year design projects at Olivet Nazarene University involve interdisciplinary engineering teams proposing product improvement designs, using Computer Aided Design (CAD) software. Posters for both the senior and freshman engineering design projects will be presented during this poster session.

Adventure Course - Hocking Hills Retreat Center, Donavan Yelle, Valerie Froylan, Nathaniel Nargang, Samantha Paterson

Scholar Week 2016 - present

Hocking Hills Retreat Center located in Logan, Ohio tasked a senior engineering design group with the creation of a high and low ropes adventure course. The goal of this course is to increase the number of visitors to the retreat center. The course was designed to feature a kid’s area; a teamwork section; and beginner, intermediate, and expert courses. All course elements range from ten to thirty feet in elevation to allow for a variety of difficulty levels. The course has been modeled using both AutoCAD and Revit software. Additionally, structural analysis was performed to ensure the safety and strength …

Aisc Structural Steel Bridge Competition, Isaac Baker, Michael Byrne, Andrew Coble, Holden Devore

Scholar Week 2016 - present

The American Institute of Steel Construction (AISC) hosts an annual competition in which students compete to design and fabricate a structural steel bridge. This year, four senior civil engineering majors are representing Olivet Nazarene University (ONU) to fulfill their capstone project requirement for the engineering department. The purpose of this project is to develop relationships between students and professionals while acquiring critical thinking skills. Through sponsor engagement, ONU’s team has developed a 3 ft-wide bridge that spans 20 ft and successfully holds up to 2,500 lbs of live load and 50 lbs of lateral load. The steel bridge is fabricated …

Data Set: The Analysis Of Lava Flow Path Using Remote Sensing Techniques And Geomorphological Techniques: The Case Of Volcano Eruptions In Afar Region Of Ethiopia, Oluwatosin Ayo, Jae Sung Kim

Michigan Tech Research Data

Natural disasters pose significant threats to the environment and make land unsuitable for man. The lava from volcanic eruptions rapidly moves on the Earth surface and affects both natural and man-made features on the Earth. Remote sensing is relevant in extracting information about the areas affected by lava flows without physically visiting such areas. The objective of this study is to develop a workflow for determining the optimal ground sample distance of a digital elevation model to delineate the lava flow paths using object-based image analysis and geomorphologic analysis. For the experiment, the satellite images and digital elevation model of …

Microplastics Fouling Mitigation In Forward Osmosis Membranes By The Molecular Assembly Of Sulfobetaine Zwitterion, Javad Farahbakhsh, Mitra Golgoli, Mehdi Khiadani, Amir Razmjou, Masoumeh Zargar

Research outputs 2022 to 2026

Forward osmosis (FO) membranes have potential for the efficient water and wastewater treatment applications. However, their development has faced significant challenges due to their fouling propensity. In this study, FO membranes modified with sulfobetaine zwitterions (i.e., [2-(Methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl) ammonium hydroxide) were fabricated and used for the first time to address microplastic (MP) fouling issue. Water flux, reverse salt flux (RSF), fouling, and flux recovery were evaluated for the membranes loaded with different quantities of the zwitterions ranging from 0.25 % to 2 %. The developed membranes were tested over 49 h with feed solutions containing polyethylene MPs and bovine serum albumin …

Box Packaging Waste Reduction By Largest Area First Fit Algorithm And Minimum Cuboid Estimation Of Irregular Shape Products, Jimmy Kwon, Sungmin Kwon

Journal of Applied Packaging Research

Nowadays, packaging waste is a prevalent issue due to the increase in deliveries from online shopping. In this research paper, a new approach to the issue of cardboard box packaging waste is proposed by selecting an optimal box that will contain both regular and irregular products while minimizing wasted volume. The method can be utilized so that packaging workers can select an appropriate, yet sustainable box. For computing a minimal cuboid of irregular objects, the system setup with two cameras is prepared to capture the overhead and sideview images, estimating the box's width, depth, and height in pixels. The proposed …

Ensemble-Learning Model Based Ultimate Moment Prediction Of Reinforced Concrete Members Strengthened By Uhpc, Woubishet Zewdu Taffese, Yanping Zhu, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Data-driven model development brings new approaches to solve conventional civil engineering problems, which are usually considered and answered by experimental, analytical, and numerical methods. This study aims to develop an ensemble learning model (i.e., XGBoost: eXtreme Gradient Boosting) to predict ultimate moment of reinforced concrete (RC) members strengthened by a newly developed concrete technology – ultrahigh performance concrete (UHPC). The study considered two scenarios, incorporating eighteen and seventeen features, with one feature modification involving the transformation of width and height to the cross-sectional area of RC members. Incorporating three substrate damage levels, two substrate surface treatments preceding UHPC strengthening, and …

Proposed Charlotte To Atlanta High-Speed Passenger Rail Line: An Economic, Infrastructural, And Developmental Analysis In The Upstate Of South Carolina, Ian C. Macurda, Kimberly Whitehead

SC Upstate Research Symposium

This research paper is an in-depth analysis of the high-speed passenger rail line proposed between Charlotte, NC and Atlanta, GA and its impact on the economy, infrastructure, and future development of the Upstate of South Carolina. Currently, passenger rail service between Charlotte and Atlanta is offered on Amtrak at late hours throughout the night on its long-distance passenger rail line The Crescent from New York City, NY to New Orleans, LA. The train is often delayed and is operating at a deficit for Amtrak, like most of their long-distance routes. Traffic on Interstate 85 through the Upstate is another issue …

Performance Enhancement Of A Solar-Driven Dcmd System Using An Air-Cooled Condenser And Oil: Experimental And Machine Learning Investigations, Pooria Behnam, Abdellah Shafieian, Masoumeh Zargar, Mehdi Khiadani

Research outputs 2022 to 2026

Solar-driven direct contact membrane distillation systems (DCMD) are disadvantaged by low freshwater productivity and low gain-output-ratio (GOR). Consequently, this study aims to achieve two primary objectives: i) improving the solar DCMD performance, and ii) harnessing machine learning models for precise and straightforward modeling of the solar DCMD system. To achieve these goals, a novel solar DCMD system powered with oil-filled heat pipe evacuated tube collectors (HP-ETCs) and equipped with an air-cooled condenser was used for the first time. The system was evaluated under eight different scenarios covering both its energy and economic performances. The performance prediction of three different machine …

On The Feasibility Of Ultrasonic Full Waveform Evaluation With Changing Testing Conditions For The Quality Control Of Manufacturing Parts, Simon Schmid, Thomas Schumacher, Christian U. Grosse

Civil and Environmental Engineering Faculty Publications and Presentations

Fast volumetric non-destructive testing methods are needed, especially for quality control in manufacturing lines. Ultrasonic testing with full waveform evaluation is a promising method for this. However, changes in coupling conditions or environmental factors can significantly alter the ultrasound signal, sometimes more than actual defects. This study investigates the effect of various factors on the ultrasound signal based on a Monte Carlo study with wavefield simulations. The test specimens comprise aluminium plates with holes of varying sizes and positions. Using both experimental as well as simulated data, the performance of two commonly used comparison metrics, namely the R2 score and …

Education And Training Networks, Ken Thomas, Joe Harrington, Robin Stubbs, Sean Carroll, Emily Shakespeare, Rahat Ullah, Adhban Farea, Theresa-Marie Greiwe

Tools

Education And Training Networks Inventory is a review of relevant network in Ireland and the EU.