Digital Commons Network^™

Effect Of Waste Covid-19 Masks On Compaction Characteristics Of Silty-Clay Soil, Sydney K. Lawson

Honors College Theses

The present study aims to explore the effect of adding shredded waste Covid-19 masks to silty-clay soil on the soil’s compaction characteristics for beneficial use in embankment, the subgrade of roadways, or backfill. This was accomplished by using two different types of masks: blue surgical masks and KN95 masks. Both mask types were hand shredded into half-inch sections using safety-scissors. The maximum dry density (MDD) and optimum moisture content (OMC) are the two most important compaction characteristics, and they were determined by the Standard Proctor Compaction Test (ASTM D698 / AASHTO T99). The change of both the MDD and OMC …

Physical And Stochiometric Controls On Nutrient Uptake And Ecosystem Respiration In Contrasting Sites, Jancoba K. Dorley

Civil Engineering ETDs

Meteorological, hydrological, and biogeochemical processes naturally control stream ecosystems. These processes define the frequency and distribution of precipitation and the supply and demand of solutes and particles to support aquatic food chains through space and time. Studies have also found that stream ecosystems are also controlled by anthropogenic activities, which occur on a much shorter timescale. These anthropogenic activities affect stream ecosystems' structure and function from local to planetary changes to the environment. It is essential for scientists and engineers to understand the relationships between naturally occurring processes and those created by human activities for a better interpretation of stream …

Investigation Into The Effect Of Mixture Composition On Setting Time Of Magnesium Phosphate Cement, Autumn Broglen

Civil Engineering Undergraduate Honors Theses

Magnesium phosphate cement (MPC) is a cementitious material that is formed through an acid-base reaction between magnesia and phosphate. This reaction occurs rapidly, making MPC an appealing choice for rapid repair applications. The purpose of this project is to investigate the impact of different proportions of class F fly ash, set retarder consisting of a mixture of boric acid and dextrose, magnesium to phosphate ratio, and water/cement ratio on the initial setting time of MPC paste. Different mixtures of MPC paste were developed to vary the proportions of each constituent, and setting time of each mixture was determined using the …

Effect Of Swirl Ratio On Simulated Vortech Chamber Vortex Parameters, Samuel Kolar

Civil Engineering Undergraduate Honors Theses

A numerical simulator can use computational fluid dynamics (CFD) to model an experimental tornado-simulating chamber at Texas Tech University (known as VorTECH). Previous studies evaluating this particular CFD model have produced results that compare the touchdown swirl ratio (S_TD), core radius (r_c), maximum tangential velocity at touchdown (V_tmax @ S_TD), and height of the maximum tangential velocity (z_c) reasonably well with experimental data from the VorTECH facility. The effects of swirl ratio beyond S_TD on important vortex parameters including r_c, V_tmax, z …

Assessment Of Engineering Performance And Environmental Impacts Of High Reclaimed Asphalt Pavement (Rap) Asphalt Mixtures In Flexible Pavements, Ibrahim A.I.E. Elnaml

LSU Doctoral Dissertations

Due to the critical role of asphalt pavements in national infrastructure development, there is a pressing need to investigate more sustainable materials and approaches. The use of natural aggregates and asphalt binders in asphalt pavement presents sustainability challenges due to the depletion of finite resources. Recycling Asphalt Pavement (RAP) offers a promising sustainable solution by substituting virgin aggregates and asphalt binders with recycled ones. However, increasing RAP contents in asphalt mixtures (>25%) can lead to premature cracking, insufficient durability, and limited longevity due to the presence of aged RAP-asphalt binder. To address these concerns, the application of novel recycling …

Safety Investigation Of Crash Rates During Hurricane Evacuations, Amelia K. Lawson

Doctoral Dissertations and Master's Theses

This study aimed to investigate crash rates across four distinct periods—evacuation, re-entry, emergency, and non-emergency—during Hurricanes Matthew (2016), Irma (2017), and Michael (2018). A notable gap in existing research pertains to understanding crash rates during these critical phases of hurricane events. By addressing this gap, this research contributes to a deeper comprehension of evacuation transportation safety. The methodology employed ArcMap to construct an interactive map for data collection, encompassing key variables such as the number of crashes, traffic volumes, duration of each period under analysis, and roadway segment lengths for each hurricane. Evaluating the crash rate per million vehicular miles …

Numerical Study Of Cone Penetration In Calcareous Sands: Investigating Cone Tip Resistance Correction Factors For Crushable Soils, Stephanie Michelle Hyder

Dissertations and Theses

The cone penetration test (CPT) is used to characterize the behavior and properties of soils, including the susceptibility to earthquake liquefaction triggering. The cone tip resistance relates to liquefaction susceptibility through relative density, where relative density is closely related to both cone tip resistance and liquefaction susceptibility. Currently, published methods of estimating liquefaction potential (i.e., cyclic resistance ratio) are based on silica sands and do not properly characterize calcareous sands. The measured cone tip resistance in calcareous sands is lower than in silica sands at the same relative density; this difference is generally attributed to the higher compressibility of calcareous …

Developing And Forecasting The Egyptian Construction Cost Index, Mayada Elsaied

Theses and Dissertations

Accurate cost estimation is pivotal for the success of construction projects, yet the industry grapples with challenges related to cost overruns. Uncertainties and unforeseen variables often introduce discrepancies, particularly during the planning phase. Economic changes, considered uncontrollable risks, significantly influence these fluctuations. Various research endeavors have quantified the impact of economic conditions on construction costs, emphasizing the correlation between economic indicators and project expenses. Addressing these challenges, the Construction Cost Index (CCI), a tool introduced by Engineering News Record (ENR), accurately delineates the correlation between economic changes and construction costs. Despite its global efficacy, an Egyptian Construction Cost Index is …

Containerization Of Seafarers In The International Shipping Industry: Contemporary Seamanship, Maritime Social Infrastructures, And Mobility Politics Of Global Logistics, Liang Wu

Dissertations, Theses, and Capstone Projects

This dissertation discusses the mobility politics of container shipping and argues that technological development, political-economic order, and social infrastructure co-produce one another. Containerization, the use of standardized containers to carry cargo across modes of transportation that is said to have revolutionized and globalized international trade since the late 1950s, has served to expand and extend the power of international coalitions of states and corporations to control the movements of commodities (shipments) and labor (seafarers). The advent and development of containerization was driven by a sociotechnical imaginary and international social contract of seamless shipping and cargo flows. In practice, this liberal, …

Laboratory Evaluation Of Warm Mix Additives At Lower Than Traditional Compaction Temperatures, Abdelrahman Mahmoud Waheish Ali

Theses and Dissertations

The study aims to evaluate the impact of warm mix additives (WMA) on the rheological and performance properties of asphalt binders and mixtures. For this purpose, PG 76-28 and PG 58-28 were obtained with one organic (Sasobit Redux) and three chemical WMA (Rediset, Evotherm, and Zycotherm). All WMA-modified asphalt binders were aged at three different aging levels. Laboratory tests such as performance grade (PG), critical temperature differential (ΔTc), asphalt binder cracking device (ABCD), linear amplitude sweep test (LAS), and Fourier transform infrared spectroscopy (FTIR) were performed. In addition to the binder testing plan, this study also evaluated the impact of …

Low-Shrinkage Fiber-Reinforced Concrete For Infrastructure Construction And Rehabilitation, Jingjie Wei

Doctoral Dissertations

"The aim of this study is to develop two classes of low-shrinkage high-performance concrete (HPC): fiber-reinforced super workable concrete (FR-SWC) for infrastructure construction and fiber-reinforced self-consolidating concrete (FR-SCC) for repair applications. HPC with excess content of shrinkage mitigation materials (SMMs), including shrinkage-reducing admixture (SRA), superabsorbent polymer (SAP), and expansive agent (EA) has a detrimental effect on mechanical performance. These classes of HPC were optimized to reduce shrinkage, enhance mechanical properties, and improve durability. The effect of fiber type (macro synthetic fiber, MSF; 5D steel fiber, 5D; 80% 3D + 20% short steel fibers; STST), SMMs, and plastic viscosity on bond …

A Structure From Motion Photogrammetric Method For Continuously Measuring And Tracking The Deformations Of Soils During Triaxial Testing, Xiaolong Xia

Doctoral Dissertations

"Measuring soil deformation characteristics during triaxial testing is an important part of characterizing the stress-strain behavior of both saturated and unsaturated soils. The total and local deformations and volume changes of a soil specimen are indispensable parameters that need to be measured and are of great significance for understanding volume change and shear strength characteristics of the soil. Over the past several decades, numerous efforts have been made to measure the soil deformations during triaxial testing. However, it remains a great challenge for researchers to measure the volume-changes of unsaturated soils due to the existence of the air phase.

This …

Impact Of Augmented Documentation Workflows On Transportation Agency Asphalt Paving Operations: A Qualitative And Quantitative Study, Josh Withrow

Theses and Dissertations--Civil Engineering

e-Ticketing was an intriguing technology to many state transportation agencies (STAs) pre-COVID-19 pandemic but gained significant attention upon arrival of the pandemic due to the contactless nature of the technology. Research completed prior to the pandemic into e-ticketing for asphalt paving primarily identified qualitative benefits and concerns. However, minimal academic literature exists in the post-pandemic era discussing the additional e-ticketing benefits not previously captured which resulted in increased implementation by STAs. This research seeks to address this gap by gathering information from state members of the American Association of State Highway and Transportation Officials Committee on Construction (AASHTO COC), employees …

Estimation Of Mechanical Behavior Of Unsaturated Soils From A Soil-Water Characteristic Curve, Lucas Acheampong

Theses and Dissertations--Civil Engineering

The small-strain shear modulus and shear strength are two crucial mechanical behaviors used in the design of geotechnical structures and in the analyses of earth materials subjected to static and dynamic loadings. Traditional testing methods for these parameters are expensive and time-consuming. This research aimed to address these challenges by developing a model based on the inverse relationship between mechanical behavior of unsaturated soils and the soil-water characteristic curve (SWCC). The proposed model integrates a scaling function to align the SWCC with the mechanical property curve. Empirical relationships were established for the scaling function, specifically aligning with the air-entry value …

Geophysical Method Used For The Determination And Prediction Of Soil Strength And Stiffness Parameters, Dabo Adama

Theses and Dissertations--Civil Engineering

This paper presents the results of an effort to use geophysical measurements such as seismic wave velocities and electrical resistivities to calculate airfield design parameters. The study converts all geophysical measurements to equivalent California Bearing Ratio (CBR) values, comparing CBR values estimated from DCP penetration resistance with CBR values estimated from shear wave velocity and electrical resistivity values. Relationships linking the geophysical measurements to CBR estimates were established using laboratory data and applied to field in-situ measurements. The elastic modulus (E) is the stiffness parameter involved in predicting soil strength and stiffness. This research aims to relate electrical conductivity and …

Comprehensive Investigation Of Using Tire-Derived Aggregate In Chip Seal Subjected To Various Traffic And Environmental Conditions, Alireza Pourhassan

Doctoral Dissertations

"Chip seal is one of the most cost- and performance-effective pavement preservation treatments commonly used in the United States. Using crumb rubber obtained from scrap tires as a partial or full replacement for mineral aggregate has been proposed as a sustainable solution to reduce the negative environmental impacts of scrap tire accumulation and excessive consumption of natural resources. However, there was no data available regarding the performance of rubberized chip seal under traffic loads and environmental conditions. An extensive study using laboratory specimens and conditioning as well as field implementation and assessments were conducted to bridge this gap. Different traffic …

Optimizing Anaerobic Digestion Of Food Waste And Industrial Sludge For Biogas Production, Emma R. Murray

Honors College Theses

Food waste is a major contributor to municipal solid waste, and its disposal at landfills has significant environmental and economic impacts. Opportunities need to be identified for the sustainable management of food waste at large scales. Pulp and paper mills throughout the country commonly use anaerobic digestion to treat their waste sludge; however, this sludge can consist of over 50% lignin, which is slowly or negligibly digested. This research aims to explore the sustainability of co-digestion of food waste and paper mill sludge. Lab-scale studies were used to assess the feasibility of anaerobic digestion by measuring treatment efficiencies and biogas …

Materials Of Lightweight Concrete Research, Meganne Chapman, Kathryn Burns, John Grubb

Williams Honors College, Honors Research Projects

The objectives for this research project are to explore options for innovative and sustainable materials in lightweight concrete. Various materials including granite powder, hydrated lime, latex, and recycled glass beads will be used in the concrete testing for this project. The question the team wants to answer is how these additives affect the concrete’s mechanical properties. Weekly mix designs will be performed, and control cylinders will be compared to experimental cylinders. Compression and tensile testing will also be performed to further aid the research. The motivation for performing this research is to aid mix development for the University of Akron …

Computationally Modeling The Human-Structure Interaction Response Of An Occupied Cantilevered Structure, Brennan Smith

Honors Theses

There is a limited understanding of the impact that passive human occupants have on a dynamic structural system, referred to as Human-Structure Interaction (HSI). Cantilevers are naturally prone to excessive vibrations due to their long unsupported spans, and cantilevered structures such as those commonly found in the seating area of a stadium facility or concert hall are designed to support a high density of occupancy.

This study determined that HSI in cantilevered structures can be modeled using a simple two-degree-of-freedom system. The results of the model were validated by data that was collected on a small-scale laboratory structure intentionally designed …

Floating Offshore Wind Turbine Analysis And Discovery, Payton Maddaloni

Honors Theses and Capstones

No abstract provided.

Floating Offshore Wind Turbine Analysis And Discovery, Payton Summer Maddaloni

Honors Theses and Capstones

This poster encompasses yearlong literary research into floating offshore wind turbines. Limitations created by society are discussed, these have prohibited large leaps to get the turbines out of the design phase. Traditional platform designs are displayed to show the potential the industry has to offer as the next renewable energy source. The maintenance phase seeks optimization. A case study by the University of Cincinnati used production losses as a consideration to lower the total cost of traditionally expensive maintenance. Finally, the end-of-life scenarios are currently being overlooked by developers. This opens the door to multiple options for disposal. Mimicking the …

Evaluation Of Aashto Seismic Design For Reinforced Concrete Bridge Columns, Andrew Leroy Grismer

Electronic Theses and Dissertations

Bridge failure can be catastrophic resulting in casualties and limiting the accessibility and emergency response efforts. Ensuring a high level of ductility for bridge columns through sufficient design methods and detailing is the most important aspect of the modern seismic codes. Reinforced concrete (RC) bridge columns are widely used in multi-span bridges located in seismic regions of the nation due to their controlled ductility and durability. The objective of this study was to systematically evaluate the AASHTO seismic design requirements for RC bridge columns and to comment on whether current bridge code is sufficient and safe. An extensive literature review …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

Electronic Theses and Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Modeling To Evaluate The Contribution Of The Built Environment On Heat Microenvironments And Analysis Of The Efficiency And Efficacy Of Electric Vehicle Purchase Incentives, Parker King

Graduate College Dissertations and Theses

This dissertation provides an integrated examination of urban heat mitigation strategies and the effectiveness of electric vehicle (EV) purchase incentives, employing innovative methodologies across its four chapters to address pressing environmental and policy challenges. It leverages a unique dataset obtained through extensive mobile sampling, state-of-the-art machine learning techniques, revealed preference data collected through robust survey design, and detailed sociodemographic analyses to offer insights into the dynamics of urban heat islands, sustainable transportation, and policy efficiency.

The first section details the quantifying of micro-environment heat differences pertaining to the influence of the built environment across 10 cities over 20 days, using …

Evaluation Of Probable Maximum Precipitation (Pmp) For West Virginia To Predict Current And Future Pmp & Utilizing Acid Mine Drainage (Amd) Sludge In Reclamation, Grace Katherine Kerr

Graduate Theses, Dissertations, and Problem Reports

This thesis includes two main topics: 1) evaluation of probable maximum precipitation (PMP) for West Virginia to predict current and future PMP, and 2) utilizing acid mine drainage (AMD) sludge as a reclamation plan.

Probable maximum precipitation (PMP) is essential for dam design as well as for the inspection, operation, maintenance, and repairs of these facilities. West Virginia Department of Environmental Protection Dam Safety utilizes the 6-hr, 10-mi² (26-km²) PMP established by Hydrometeorological Report (HMR) 51 based on the analysis of extreme rainfall. These PMP are outdated because there have been unaccounted for extreme rainfall events that …

Uncertainty Quantification Of Live Load Effect In Buried Rc Box Culverts, Mohd Firoj

Dissertations and Theses

Although buried and mostly invisible to the traveling public, bridge-sized culverts (i.e., culverts with span around or longer than 20 ft) account for a large proportion of state-managed bridges. As per Oregon Department of Transportation inventory, there are approximately 35,000 culverts in the state highway system. Among them, 10,862 are in poor conditions and need to be analyzed for load rating purposes. The prediction and understanding of live load effects in culverts are crucial to the design, evaluation, and life-cycle maintenance of culverts. These live load effects include maximum bending moments and shear forces at different critical cross sections.

This …

Early-Age Strength And Failure Characteristics Of 3d Printable Polymer Concrete: Numerical Modelling And Experimental Testing, Mohammad Amin Dehghani Najvani

Civil Engineering ETDs

The time-dependent rheological and early-age strength parameters of Polymer concrete (PC) were investigated. PC flow decreased, and the static yield stress and thixotropy increased as the specimen aged, while the dynamic yield stress remained unchanged. The study found that the Herschel-Bulkley model can accurately describe the PC’s rheological behavior over time. The change in cohesion strength and internal friction angle over time was observed using uniaxial unconfined compression and direct shear tests of fresh PC. A time-dependent MohrCoulomb failure criterion was established. Temperature analysis was used to determine the gel time and explain the evolution of the time-dependent early-age strength …

Modeling Of Asphalt Concrete For Cross-Anisotropic Visco-Elasticity And Heterogeneity, Zafrul Hakim Khan

Civil Engineering ETDs

Asphalt Concrete (AC) is a cross-anisotropic viscoelastic material. This study has developed a methodology to backcalculate the cross-anisotropic properties of the AC layer from the Falling Weight Deflectometer (FWD) sensor and pavement response data from embedded sensors inside a pavement section. This study has also developed a two-way coupled Multiscale Finite Element Model (MsFEM) with Phase Field Fracture (PFF) to study the microstructural heterogeneity and damage of the AC layer based on the actual field loadings. A Finite Difference Time Domain (FDTD) and Machine learning-based backcalculation algorithm were developed to determine the layer thickness and dielectric constant from air-coupled Ground …

Analysis Of Loading Rate, Fiber Orientation And Material Composition Through Image Processing And Digital Volume Correlation In High Performance Concrete, Aidan R. Carlson

Electronic Theses and Dissertations

Ultra High Performance Concrete (UHPC) and High Performance concrete (HPC) is characterized by high compressive strength and high toughness. This is achieved through maximizing the particle packing density in the matrix and the use of fibers to reinforce the matrix, increasing the materials toughness. The interactions of fibers and the matrix during loading is quite complex and involves several different energy dissipation mechanisms. The goal of this work and this thesis is to investigate these interactions and identify any changes in material response, and hope that these changes may be useful for the design of UHPC moving forward.

In this …

Examining The Impact Of Centerline Rumble-Strip Installation In Prevention Of Head-On And Opposite Sideswipe Collisions In Maine, Jhan Kevin Gil Marin

Electronic Theses and Dissertations

Among all traffic collisions, lane departure crashes are the leading type of serious traffic crashes in Maine, comprising 72% of state-wide traffic fatalities. To reduce these crashes, Maine Department of Transportation (MaineDOT) installed shoulder and centerline rumble strips on roadways to prevent lane departure crashes in Maine. With a total installed length of 1503 miles of rumble strips, specifically 511 miles of centerline rumble strips in bidirectional and undivided rural two-lane roadways, there is a need to understand the impact of rumble strips in reducing lane departure crashes. In this thesis, observational before-after studies with two methods: comparison group, and …