Digital Commons Network^™

Finite Element Modeling Of Patient-Specific Total Shoulder Arthroplasty, Ignacio Rivero Crespo

Electronic Theses and Dissertations

Total Shoulder Arthroplasty (TSA) is a surgical procedure designed to improve joint functionality by replacing the articulation between the humeral head and the glenoid fossa. Anatomic Total Shoulder Arthroplasty (aTSA) and Reverse Total Shoulder Arthroplasty (rTSA) are two types of replacement surgery to relieve pain and restore function of the shoulder. The overall goal of this study was to evaluate the effects of variation of certain patient and implant alignment parameters that may influence long-term outcomes of these surgical procedures, including kinematics, joint loads and contact mechanics. Computational models of six TSA subjects, three aTSA and three rTSA, were created …

The Influence Of Heat And Mass Transfer On The Setting Rate Of Adhesives Between Porous Substrates, Mubarak Mohammed Khlewee

Electronic Theses and Dissertations

The dynamic penetration of fluid into a porous media where other changes are occurring such as temperature or concentration is of interest to a number of situations. However, little experimental and theoretical analysis of this situation is found in the literature where most of the previously published works have studied the penetration with constant physical properties, where there is no change of the fluid as it enters the pores. This situation is important in the setting of adhesives in porous medium such as in the setting of hot melt and water-based adhesives in the production of paper based packaging. The …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Full Bridge Modeling To Evaluate Effectiveness Of A Seismic Bearing On A Newly Constructed Bridge On I-55, Sandip Gupta

Electronic Theses and Dissertations

Infrastructure constructed should be safe and reliable. Bridges are essential infra structure used by large mass of people on a daily basis. Out of 617,000 bridges across the United States, 42% are at least 50 years old, and 7.5% are considered structurally deficient as per Infrastructure report card. 178 million trips are made on these structurally deficient bridges every day in the US. Thus, a bridge should be designed, not only for Strength and Service limit states, but also for Extreme limit states which includes earthquake. New Madrid Seismic Zone (NMSZ), located in southeastern Missouri, northeastern Arkansas, western Tennessee, western …

Addressing Soil Carbon Sequestration Response From Multispecies Dairy Forage Systems And Modeling Rangeland Beef Cow Dry Matter Intake Using Precision Enteric Emissions Measurements, Lillian J. Mcfadden

Electronic Theses and Dissertations

Regenerative agriculture is a pressing matter for the dairy industry to address cropland sustainability and carbon sequestration. One regenerative management practice that has been identified to help with row crop sustainability for key metrics like soil organic carbon (SOC) is complex covers. When producers use complex covers one of the main challenges is that it takes time to detect a change in SOC. However, simulation models are a tool that can be used to help determine if a regenerative practice is a strategy that gives the best results (i.e., increased SOC) while aligning with long-term production goals. Therefore, our objectives …

Development And Evaluation Of Performance Models For Asphalt, Concrete, And Composite Pavements Using Machine Learning, Rulian Ferreira De Almeida Barros

Electronic Theses and Dissertations

Transportation infrastructures account for a considerable portion of public investments, which serve as the backbone of a country’s economy by providing essential services to businesses and people. In the United States, public investments in transportation infrastructure assets represent trillions of dollars. The U.S road network consists of about 4 million miles, being the world’s largest, longest, and biggest transportation system. Paved roads account for 2.6 million miles, and 93% of them are surfaced with asphalt. However, a portion of the paved roads consists of asphalt overlaid concrete pavements, also known as composite pavements. When concrete pavements start to fail, they …

The Effect Of Initial Conditions On The Weather Research And Forecasting Model, Aaron D. Baker

Electronic Theses and Dissertations

Modeling our atmosphere and determining forecasts using numerical methods has been a challenge since the early 20th Century. Most models use a complex dynamical system of equations that prove difficult to solve by hand as they are chaotic by nature. When computer systems became more widely adopted and available, approximating the solution of these equations, numerically, became easier as computational power increased. This advancement in computing has caused numerous weather models to be created and implemented across the world. However a challenge of approximating these solutions accurately still exists as each model have varying set of equations and variables to …

Quantifying The Impacts Of Land Use, Management And Climate Change On Water Resources In Missouri River Basin, Arun Bawa

Electronic Theses and Dissertations

A location-specific evaluation of hydrological landscape responses concerning past and projected climate and land use land cover (LULC) changes can provide a powerful intellectual basis for developing efficient and profitable agroecosystems, and overcoming uncertain and detrimental consequences of LULC and climate shifts. This dissertation assessed the impacts of land use, management, and climate change on water resources in the Missouri River Basin (MRB) through four specific studies that included: (i) to study the responses of leached nutrient concentrations and soil health to winter rye cover crop (CC) under no-till corn (Zea mays L.)-soybean [Glycine max (L.) Merr.] rotation, (ii) to …

The Effects Of Elevation On Foraging Behavior Of Bats In Southern Appalachia, Victoria Long

Electronic Theses and Dissertations

There are limited studies on bat activity in higher elevations in the Appalachian region. Levels of bat activity were compared in south central Appalachia at low (< 914.4 m) and high (> 1, 524 m) elevations in open, forest edge, and riparian habitats. Additionally, habitat suitability was modeled for a common species, big brown bat (Eptesicus fuscus). The study started May 27^th 2019, and sites were monitored biweekly until October 2^nd 2019. Six species and one genus were recorded during the study. Species from the Myotis genus were grouped together because of similar call characteristics. Results show that species were significantly more …

Utilizing The Public On Public Lands: The Application Of Community Science To Monitor And Model Erosion In National Forests, Jacob L. Hansen

Electronic Theses and Dissertations

Unpaved forest roads are adversely affecting coldwater streams through excessive erosion and the subsequent sedimentation of adjacent waterways. To help identify areas of concern, Trout Unlimited (TU) in the Southern Appalachian region developed a Community Science initiative to gather data on sediment sources and stream-road crossings. Volunteers were recruited and trained to monitor road and trail conditions and collect and submit data using a Survey123 application on their cell phones. Analysis of the contributed data reveals statistical connections between drainage type and both erosion level and stream sedimentation. The contributed data were also included as a calibration for the lite …

Image Space Coverage Model For Deployment Of Multi-Camera Networks, Eslam Samir Eissa

Electronic Theses and Dissertations

When it comes to visual sensor networks deployment and optimization, modeling the coverage of a given camera network is a vital step. Due to many complex parameters and criteria that governs coverage quality of a given visual network, modeling such coverage accurately and efficiently represents a real challenge. This thesis explores the idea of simplifying the mathematical interpretation that describes a given visual sensor without incurring a cost on coverage measurement accuracy. In this thesis, coverage criteria are described in image space, in contrast to some of the more advanced models found in literature, that are formulated in 3D space, …

Changes In Land Use Land Cover (Lulc), Surface Water Quality And Modelling Surface Discharge In Beaver Creek Watershed, Northeast Tennessee And Southwest Virginia, Tosin James

Electronic Theses and Dissertations

Beaver Creek is an impaired streams that is not supporting its designated use for recreation due to Escherichia coli (E.coli), and sediment. To address this problem, this thesis was divided into two studies.

The first study explored changes in Land Use Land Cover (LULC), and its impact on surface water quality. Changes in E.coli load between 1997-2001 and 2014-2018 were analyzed. Also, Landsat data of 2001, and 2018 were examined in Terrset 18.31. Mann-Whitney test only showed a significant reduction in E.coli for one site. Negative correlation was established between E.coli load, and Developed LULC, Forest LULC, and …

Semi-Analytical Approach Towards Design And Optimization Of Induction Machines For Electric Vehicles, Aida Mollaeian

Electronic Theses and Dissertations

Electric machine design is a comprehensive task depending on the several factors, such as material resource limitations and economic factors. Therefore, an induction machine is a promising candidate because of the absence of magnetic material in the rotor. However, the conventional design approach can neither reflect the advances of the induction machine(IM) design nor exploit the trade-offs between design factors and the multi-physics nature of the electrical machine. Therefore, proposing fast and accurate novel methods to design, develop and analyze IMs using electromagnetic field oriented approaches is competitive to the old-fashion numerical methods. To achieve improved IM design from a …

Seeing The World Differently. An Exploration Of A Professional Development Model Bridging Science And Lay Cultures, Michael D. Garrett

Electronic Theses and Dissertations

This study explores the rationale, efficacy, and social validity of a professional development model designed to move elementary school science activities closer to the practices of working scientists as required by the United States’ “Next Generation Science Standards.” The model is culturally sensitive and aims to create experiences with high subjective task value. The formal theory of change uses scaffolding, Piagetian agency, and Vygotskian learning opportunities to argue that culturally familiar representational tasks in culturally natural intersubjective contexts can lead to work prototypical of scientific modeling under particular facilitation conditions: when participants (a) are allowed free use of their cognitive …

Synergistic Environmental Aging Of Glass Reinforced Polymer Composites, Tianyi Lu

Electronic Theses and Dissertations

Synergistic effects involved in the environmental degradation of Glass Reinforced Polymer (GRP) composites were examined and a novel synergistic aging model was proposed in this study. Six GRPs based on glass fibers with four different polymer resins and six pure polymer thermoplastic resins were exposed either individually or in combination to ultraviolet (UV) radiation, water condensation and elevated temperature for approximately 1000 h. The composites and polymers were monitored for weight changes as a function of time and their surfaces were examined after the tests using optical and scanning electron microscopes (SEM). Photodegradation of the polymer matrices was analyzed by …

Computational Modeling And Simulations Of Condition Deterioration To Enhance Asphalt Highway Pavement Design And Asset Management, Zul Fahmi Bin Mohamed Jaafar

Electronic Theses and Dissertations

A nation’s economy and prosperity depend on an efficient and safe transportation network for public mobility and freight transportation. A country’s road network is recognized as one of the largest public infrastructure assets. About 93 percent of 2.6 million miles of paved roads and highways in the United States (U.S.) are surfaced with asphalt. Longitudinal roughness, pavement cracking, potholes, and rutting are the major reasons for rehabilitation of asphalt roads. Billions of dollars are required annually for the maintenance and rehabilitation of road networks. If timely maintenance and rehabilitation are not performed, the pavement damages inflicted by heavy traffic repetitions …

A Descriptive Analysis Of Rehearsal Techniques Of Expert Middle School Band Directors From Kentucky, Mississippi, And Tennessee, David John Culp Jr

Electronic Theses and Dissertations

The purpose of the present study was to identify rehearsal techniques among expert middle school band directors Kentucky, Tennessee, and Mississippi. Twenty-one potential participants were recommended by university faculty and other leaders within the profession. Seven directors were identified who met criteria for participation in the study. Six directors agreed to participate, but due to scheduling conflicts, five were observed. Participants were observed and video recorded for three consecutive rehearsals. Initial analysis divided rehearsals into subsections including: warm-up, repertoire rehearsal, run-through performance, and non-instructional time. Repertoire rehearsal time for all participants was then systematically analyzed using rehearsal frames with two …

Modeling And Simulation Of The Thermoforming Process In Thermoplastic-Matrix Composite Materials, Philip M. Bean

Electronic Theses and Dissertations

Thermoplastic-matrix composite materials have unique advantages over traditional thermosets including faster processing, improved fracture toughness, and recyclability. These and other benefits have caused increasing interest in the use of these materials in both aerospace and automotive industries. Due to the differences in behavior, these materials require a different type of manufacturing process to thermoset matrix composites. This manufacturing process generally involves using pre manufactured tape-layers. These layers, containing both thermoplastic-matrix and fiber-reinforcement, are aligned to the desired orientation, and stacked up into a “tailored blank” using an automated tape layup machine. They are then heated to the thermoplastic melting temperature …

Accessible Poi Recommendation Using Adaptive Aggregation Of Binary Ratings, Bidur Subedi

Electronic Theses and Dissertations

Everyone needs one or more forms of accessibility at some point in life due to age, medical conditions, accidents, etc. People with accessibility needs have the right to accessible services, as well as the right to information about accessibility at various places or Points of Interest (POI). While most popular POI recommendation services do not take accessibility into account, some of them only consider a few specific needs, such as ramp for wheelchair users. However, different users have different accessibility needs regarding the structure of the building, special aid devices, and facilities to be able to independently visit a place. …

Fm Radio Signal Propagation Evaluation And Creating Statistical Models For Signal Strength Prediction In Differing Topographic Environments, Timothy Land

Electronic Theses and Dissertations

Radio wave signal strength and associated propagation models are rarely analyzed across individual geographic provinces. This study evaluates the effectiveness of the Radio Mobile model to predict radio wave signal strength in the Blue Ridge and Valley and Ridge physiographic provinces. A spectrum analyzer was used on 19 FM transmitters to determine model accuracy. Statistical analysis determined the significance between different terrain factors and signal strength. Field signal strength was found to be related to test site elevation, transmitter azimuth, elevation angle, transmitter elevation, path loss, and distance. Using 76 signal strength receiver sites, Ordinary Least Square regression models predicted …

Learning From Disorder And Noise In Physical Biology, Taylor Emil Firman

Electronic Theses and Dissertations

Stochasticity, disorder, and noise play crucial roles in the functioning of many biological systems over many different length scales. On the molecular scale, most proteins are envisioned as pristinely folded structures, but intrinsically disordered proteins (IDPs) have no such folded state and still serve distinct purposes within the cell. At the scale of gene regulation, realistic in vivo conditions produce stochastic fluctuations in gene expression that can lead to advantageous bet-hedging strategies, but can be difficult to characterize using a deterministic framework. Even at the organismal scale, germband extension (GBE) in Drosophila melanogaster embryos systematically elongates the epithelial tissue using …

Effect Of Poisson’S Ratio On Young's Modulus Characterization Using Ultrasonic Technique By Modeling, Michael Onyetube

Electronic Theses and Dissertations

The past 27 years has witnessed a revolutionary growth in the progress of material development and application in almost all industry and business sectors, and this seems to be continuing even today. So many material-driven innovations have enabled the global spread in technology and improvements in capability, ranging from communications to aerospace and healthcare, to automotive and agriculture. Mechanical behavior of elastic materials is modeled by two main independent constants; Young’s modulus and Poisson’s ratio. An accurate measurement of both constants is necessary in most engineering applications, for example, the standard materials used for the calibration of some equipment, quality …

A Framework For Assessing Water Quality, Prioritizing Recovery Potential, And Analyzing Placement Of Best Management Practices, Tadesse Animaw Sinshaw

Electronic Theses and Dissertations

Motivated by the U.S. EPA goals, this research developed a framework to support identification and restoration of nutrient-impaired water bodies. The study objectives were developing total nitrogen (TN) and total phosphorus (TP) prediction models, evaluating the impact of social indicators on assessing recovery potential, and developing a spatial decision support system for choice and placement of best management practices (BMPS). An artificial neural network was used to develop TN and TP predictive regional models for U.S. lakes using easily measurable and cost-effective variables. The performance of models was superior for regions trained with larger datasets and/or regions with lower temperature …

Duality, The Methodology Of Shooting A Documentary As A One-Man Crew, James Mcmahen

Electronic Theses and Dissertations

This thesis will discuss Duality, a long-form documentary about artistic nude models who also create art involving the nude female form. This thesis will discuss the inspiration for the film, as well as the deciding factors that made me choose this as the topic for my thesis documentary.

This thesis will also cover the process and methodology of shooting a documentary as a one-man crew, beginning with the process of preproduction, then the principal photography of the documentary, followed by the editing and postproduction process, and finally premiering the final film.

Novel Techniques For Torque Ripple Modeling And Minimization In Permanent Magnet Machines, Chunyan Lai

Electronic Theses and Dissertations

This thesis investigates torque ripple modeling and minimization techniques for permanent magnet (PM) machines to achieve high-performance and reliable machine drive for practical industrial and consumer applications. At first, a comprehensive torque ripple model is proposed, in which the torque ripples resulting from the spatial harmonics of magnet flux, the time harmonics of stator currents and the cogging torque are included. Since the proposed torque ripple model involves machine operation dependent parameters, the effects of parameter variation on PM machine torque ripple modeling are investigated, to improve the accuracy and robustness of the proposed model. The key to torque ripple …

System Identification Of A Circulation Control Unmanned Aerial Vehicle, Mohammed Agha

Electronic Theses and Dissertations

The advancement in automation and sensory systems in recent years has led to an increase the demand of UAV missions. Due to this increase in demand, the research community has gained interest in investigating UAV performance enhancing systems. Circulation Control (CC), which is an active control flow method used to enhance UAV lift, is a performance enhancing system currently studied. In prior research, experimental studies have shown that Circulation Control wings (CCW) implemented on class-I UAVs can reduce take-off distance by 54%. Wind tunnel tests reveal that CC improves aircraft payload capabilities through lift enhancement. Increasing aircraft payload capabilities causes …

Statistical Shape Modeling To Quantify Variation In The Proximal Humeral Anatomy, Paul B. Sade Sr.

Electronic Theses and Dissertations

The fit of the humeral prosthesis to the intramedullary canal and the replication of the anatomic humeral head center are important factors in Total Shoulder Arthroplasty (TSA). The objective of this thesis was to develop a Statistical Shape Model (SSM) of the cortical and cancellous bone regions of the proximal humerus, and to assess potential shape differences with gender and ethnicity, with a goal of informing implant design. An SSM was used and Principal Component Analysis (PCA) was applied to data that represented both the cancellous and cortical humeral bone of 63 healthy subjects and cadavers. Anatomical measurements and PC …

The Effect Of A Researcher Composed Mouthpiece Buzzing Routine On The Intonation And Tone Quality Of Beginning Band Brass Students, Jason William Beghtol

Electronic Theses and Dissertations

The present study is an investigation of the effect of an author composed mouthpiece buzzing routine modeled by the teacher on beginning band brass students’ intonation and tone quality. The subjects (N = 43) were sixth grade beginning band brass students from a large band program in the northeast region of Mississippi. The experimental group (n = 27) buzzed a daily routine modeled by their instructor at the beginning of each class period. The control group (n = 16) received no treatment and proceeded through normal classroom activities. The duration of the instructional period was ten weeks. This study utilized …

Specimen-Specific Natural, Pathological, And Implanted Knee Mechanics Using Finite Element Modeling, Azhar Akber Ali

Electronic Theses and Dissertations

There is an increasing incidence of knee pain and injury among the population, and increasing demand for higher knee function in total knee replacement designs. As a result, clinicians and implant manufacturers are interested in improving patient outcomes, and evaluation of knee mechanics is essential for better diagnosis and repair of knee pathologies. Common knee pathologies include osteoarthritis (degradation of the articulating surfaces), patellofemoral pain, and cruciate ligament injury and/or rupture. The complex behavior of knee motion presents unique challenges in the diagnosis of knee pathology and restoration of healthy knee function. Quantifying knee mechanics is essential for developing successful …

Modeling And Forecasting The Influence Of Current And Future Climate On Eastern North American Spruce-Fir (Picea-Abies) Forests, Caitlin Andrews

Electronic Theses and Dissertations

The spruce-fir (Picea-Abies) forest type of the Acadian Region is at risk of disappearing from the United States and parts of Canada due to climate change and associated impacts. Managing for the ecosystem services provided by this forest type requires accurate forecasting of forest metrics across this broad international region in the face of the expected redistribution of tree species. This analysis linked species specific data with climate and topographic variables using the nonparametric random forest algorithm, to generate models that accurately predicted changes in species distribution due to climate change. A comprehensive dataset, consisting of 10,493,619 observations …