Digital Commons Network^™

Controlling Relative Humidity Using Glycerin, Juan Martinez

Civil Engineering Undergraduate Honors Theses

A series of tests were conducted to control relative humidity (RH) using a bubbler system that contained a series of glass jars and glass vials filled with different concentrations of glycerin. The relative humidity within the glass jars was measured. The total time interval for each laboratory test was 48 hours. During the first 24 hours a pump was used to bubble air through the glycerin solution. During the second 24 hours, the pump was turned off, and the RH within the system was monitored within the closed system. Target RH measurements from 100% to a 0% were obtained. The …

Young’S Modulus As A Measurement To Estimate Damage Related With Alkali-Silica Reaction In Concrete., Anazaria J. Ortega Gonzalez

Civil Engineering Undergraduate Honors Theses

The main purpose of this research is to compare two nondestructive methods to assess Alkali-Silica reaction (ASR) in concrete. Fifteen concrete prisms were cast using aggregates with different Alkali-Silica reactivity such as Jobe sand and Van Buren sand. The change in strain, shear wave velocity and Young’s modulus were determined according to ASTM C129 and ASTM C215, respectively. This data was collected by Dillon K Self, who determined that the shear wave velocity and strain are inversely proportional. However, when single cracking in the concrete specimen transition to map cracking, the shear wave velocity dropped significantly, whereas the strain value …

Evaluation Of A Centrifuge Consolidation Technique To Determine The Effects Of Temperature And Time On Kaolinite Properties, Esteban Miranda Pinzon

Civil Engineering Undergraduate Honors Theses

Abstract

The effects of time and temperature on the moisture content and unit weight profiles, as developed during a centrifuge consolidation process, were observed during the research program that is described herein. Specifically, a Beckman-Coulter Model J6-MI centrifuge with a six-place JS-4.2A swinging bucket rotor was utilized to consolidate kaolinite slurry samples. The consolidation procedure utilized specially designed slurry consolidometers, made from acrylic tubes with inside diameters of 2.63 inches (6.67 cm) and heights of 5.13 inches (13.04 cm). The tested kaolinite slurry samples were created by mixing 400 grams of dry kaolinite clay powder with 200 grams of de-aired …

Service Learning Through Extracurricular Activities: Development And Implementation Of A Transportation Engineering Learning Module, Karla Diaz Corro

Civil Engineering Undergraduate Honors Theses

This project developed an easy to implement, low-cost learning module. The module has students compare and contrast the challenges of gathering comprehensive and quality transportation data through advanced technologies and traditional approaches while introducing traffic engineering topics like traffic signal timing. The modules target middle through high school students and first and second year undergraduate engineering students. The learning modules introduce transportation engineering using an engaging open-source computer simulation game adapted by students at the University of Arkansas, as part of a capstone project. The activities in the learning modules require off-the shelf, low-cost computer hardware, making it easy for …

Development Of A Hydraulic Conductivity Placement Window Using Centrifuge Techniques, Greg Thomas

Civil Engineering Undergraduate Honors Theses

A centrifuge soil testing device, currently operated by researchers at the University of Arkansas, was used to develop a technique to determine a hydraulic conductivity placement window. The purpose of this research was to develop a placement window by means of a centrifuge instead of by means of a panel board. Soil specimens were created at standard PRcotor energy and at 50 percent of Standard Proctor energy at -3 percent of optimum, -1.5 percent of optimum, two specimens at optimum, +1.5 percent of optimum, and +3 percent of optimum water content. Values of hydraulic conductivity for the respective specimens were …

Improving Spatial Visualization Abilities Using 3d Printed Blocks, Vanessa Lebow, Michelle Bernhardt-Barry, Jyotishka Datta

Civil Engineering Undergraduate Honors Theses

Spatial visualization abilities have been shown to be a key predictor of success in science, technology, engineering, and math fields. Past research has revealed that women and underrepresented minorities tend to lag behind in spatial visual abilities, however, research has also shown that these skills can be improved with guided practice. This study seeks to examine whether 3D printed aids help spatial visual retention in 6th graders. A modified Purdue spatial visualization test was used as the assessment standard. Students’ mental rotation abilities were assessed before and after the 3D printed aids were administered. Data was collected from five different …