Digital Commons Network^™

Correlation Between Particle Velocities And Conditions Of Abrasive Waterjet Formation, Wei-Long Chen

Dissertations

The velocities of water and abrasive particles in abrasive waterjet(AWJ) were measured by the use of Laser Transit Anemometer(LTA). A setup for the velocity measurement was constructed and a statistical technique was used to improve the accuracy of the velocity determination. A comparison of the magnitude of velocities determined by LTA, Piezoelectric Force Transducer and Schlieren Photograph clearly indicates the feasibility of the use of LTA.

The velocities of water and particles were measured for different diameters of water and slurry nozzles, abrasive mass flow rates and particle sizes. The performed experiments enabled us to evaluate the effects of conditions …

Aqueous Absorption Of Nox Induced By Sodium Chlorite Oxidation, Chen-Lu Yang

Theses

Aqueous scrubbing in alkaline media for the removal of nitrogen oxides (NO_x) from flue gases using NaClO₂ as an oxidant is being investigated in the Chemical Engineering Department of New Jersey Institute of Technology. This thesis presents the findings of an experimental program that was conducted to estimate the capability of NaClO₂ aqueous solution to oxidize insoluble NO to soluble NO₂ in order to increase its solubility and thus prevent NO_x emission from entering the atmosphere from flue gases emitted by municipal incinerators or power plants.

The key findings of this program are:

* …

Application Of Microwave Technology To Effect On-Site Regeneration Of Gac, K.C. Mahesh

Theses

The off-site regeneration of granulated activated charcoal(GAC), spent as a result of stripping of organics from aqueous waste streams, represents a burdensome cost both because of the actual cost of regeneration and legal liability associated with shipping a hazardous waste off-site: that liability is reflected in huge potential costs associated with mishaps enroute for the self-insured or high premiums paid to the casualty insurance companies for those generators that are insured by third parties. Thus there is a need for the development of a process to effect on-site regeneration of spent GAC cost-effectively.

This thesis mainly focuses on the technical …

Propagation Of Millimeter Wave Signals In Forests Using The Equation Of Radiative Transfer With Strong Forward Scattering Phase Functions, Nack Yang Cho

Dissertations

A forest is a highly scattering medium at millimeter wave frequencies. The propagation of cw millimeter wave signals in forests has been studied previously, both theoretically and experimentally. Published experimental data verified that continuous wave transmission is possible over lengths of the order of a few hundred meters and that a forest acts to strongly scatter energy in the forward direction. The cw studies yielded the determination of the range dependence, beam broadening effects and depolarization effects of millimeter wave signals in a forest. However, pulse broadening effects, which are of importance particularly in the case of digital signal transmission, …

Toward A Model Of Instruction For Architecture Design Studio, Garry Allen Perryman

Theses

This inquiry addresses some fundamental issues raised in a debate over the effectiveness of architecture studio instruction. It argues that as currently structured the studio's potential effectiveness is often unrealized, because of the paucity of standardized educational resources and instructor's lack of training in educational theories of instruction. This has resulted in instructional planning that is seldom structured on educational theory or research. It is also argued that in order to maximize it's effectiveness, beginning studio instruction must be premised upon a theory of instruction which includes specifying explicit instructional goals and objectives and that this would create a more …

Study Of Acetone Extractable Organic Matter From Airborne Particulate Matter From An Urban Site, Wenhui Wu

Theses

Two seasonal periods (Winter 1988; Summer 1988) of daily Newark urban air samples were collected on glass fiber filters. Each filter was first extracted with dichloromethane and subsequently with acetone. Quarterly composites of each were then tested for mutagenicity. The results of the analysis of the less polar dichloromethane extracts were reported in the thesis of Junghen Lwo. A modified fractionation scheme involving acid-base partitioning and silica gel column chromatography has been used as the first step in the bioassay-directed search for significant levels of mutagenic compounds in extracts of inhalable (IP 10) ambient air particulates. The biologically "hot" fractions …

Thermal Decomposition Of Chlorobenzene Reaction With Hydrogen And Oxygen Mixture In An Atmosphere, Chun-Chen Yang

Theses

The thermal reactions of chlorobenzene in hydrogen and oxygen mixtures were studied in tubular flow reactors at 1 atmosphere total pressure. Experiments were carried out in flow reactors of varied diameter for determining effects of different surface to volume ratios. Residence times ranged from 0.03 to 2.5 seconds and temperature was varied over a range of 560 - 660 °C. The 02/H2 ratios ranged from 1% to 5%.

It was found that the conversion of chlorobenzene in hydrogen and oxygen mixtures increased with both temperature and residence time. The oxidation of chlorobenzene also occurred more rapidly when oxygen concentraction was …

A Comparison Study Between The Tenax Trap And The Canister Collection Methods For Determination Of Volatile Organic Compounds, Li-Ching Lillian Hung

Theses

A comparison between the analytical methods for determination of volatile organic compounds, using Tenax GC as an adsorbent and using stainless steel canister collection is made.

Sample collection, analytical system and procedures, data analyses, as well as their fortes and their drawbacks, etc., are discussed.

In addition, a brief description of the developmental history of the above methods as used in the Air Pollution Research Laboratory at the New Jersey Institute of Technology in Newark, New Jersey, is given.

Agitation Requirements For Complete Drawdown Of Floating Solids In Stirred Tanks, Joseph Philemon Mmbaga

Theses

The agitation requirements for complete drawdown of floating solids in mechanically agitated tank vessels has been studied both theoretically and experimentally.

A semi-theoretical equation has been derived on the basis of Kolmogoroff's theory of isotropic turbulence to determine the minimum impeller speed required for drawdown. The equation contains one adjustable parameter which has been found to be a function of the impeller type and position in the tank vessel.

The equation was tested using various vessels and impeller configurations. The solid phase consisted of high density polyethylene (density = 897kg/m³), low density polyethylene (density = 840kg/m³) …

Process Modelling Of The Nitration Of Toluene, Nitin K. Shah

Theses

The thesis on the process modelling of the nitration process focuses specifically on the product separation of the nitrated aromatic material from the reactor and - wash section of the process. Included in the text is an overview of the main process steps associated with the production of para and ortho-nitrotoluene. The critical issues concerning the reaction of nitric acid and toluene were summerized, and resulted in this subject being deferred for future work.

The separation of the isomers into pure components is an important. part of the MNT process because of the close high boiling points of the isomeric …

Analysis Of C2 And C3 Hydrocarbons In Ambient Air. Part 1 ; Development Of Simple Analysis For Polycyclic Aromatic Hydrocarbons. Part 2, Li-Li Wu

Theses

SECTION I

A method was developed to analyze C₂ and C₃ light hydrocarbons: Acetylene, Ethylene, Ethane, Propyne, Propylene and Propane levels in the ambient air. Chlorinated compounds which eluted within the gas chromatograph operation conditions needed for the above hydrocarbons included Freon 12 and Methylene chloride, were also monitored.

Samples were collected from two sites, one located at Carteret and one at Elizabeth New Jersey. Samples were taken from September 1988 through July 1989. The sampling method used stainless steel canisters and was set up to collect 24 hour air samples at a constant flow rate of 30-35 …

Protein Separation With Mathematical Modeling For Chromatographic Operation, Hsien-Chih Ma

Dissertations

We have performed experiments and derived mathematical models for packed bed columns used for liquid phase chromatographic separations of proteins with impulse input of feed solutions. These models can now be used to describe the relationships between the elution characteristics (peak height, peak position, and shapes) and the operating conditions (flow rate and buffer conditions) of ion exchange and gel permeation column chromatography for protein separations.

The surface adsorption model was discussed relative to the nature of the mobile and stationary phases in ion exchange column chromatography for two distinct cases: with and without pore diffusion. For large solute molecules, …

Computerize Data Information For Architecture Design, Syau-Yi Yu

Theses

Computer-aided architectural design is technically and commercially feasible yet experience in the architectural profession to date is paradoxical. Many who apply computers to architecture appear satisfied but the tangible benefits are seldom obvious and even where computers are used in firms it is not done to the fullest potential. Contents of this thesis are an attempt to help architecture better utilize the advantages of computer applications.To do this it is important to examine two question: what is design and what is the computer? They are similar yet distinct. Architectural design is a special kind of problem solving process; an information …

First Impression : The Study Of Entry In Architecture, Siriwan Polpuech

Theses

Entrance as an element of architecture has had an important role in the design process from the very beginning of the architecture. Its role varies according to culture and the belief of people. The characteristics of entrances are as diversified as are architectural style and historic periods.

Architectural styles continue to change. New forms and technologies add to the growth of styles. All these contribute to the eclectic of design ideas. The specifics of an entrance can arise from, be complementary to or in contradiction of a style. They always serve as a mediator between interior and exterior spaces. The …

Towards A Theory Of Planning Aesthetics : Application To University Commons, Newark, Kathy M. Gonzalez

Theses

A theory of planning aesthetics will be developed and discussed in relation to a portion of the university area of Newark consisting of N.J.I.T., Rutgers, Essex County College, University of Medicine and Dentistry of New Jersey. The site is just east of the campuses and contains the Newark Museum and the Newark Library.

The aesthetics of order will be covered at a community scale (the urban context) which will then be detailed as a study of the fractile portion of that entity (the building entity) relative to open spaces which give both entities character. Important in this work is three-dimensional …

Biodegradation Of Benzene And A Btx Mixture Using Immobilized Activated Sludge, Mayur Padamshi Lodaya

Dissertations

Aerobic biodegradation of benzene was studied using activated sludge immobilized in calcium alginate (immobilization by entrapment), and also attached to a silica based catalyst.support (immobilization by attachment). Hydrogen peroxide was used as a source of dissolved oxygen to eliminate physical removal of benzene due to aeration. Abiotic losses of benzene were accounted for.

A recirculation reactor, run in both batch and continuous feed mode, was used to determine the kinetic parameters. The system response was examined by tollowing changes in benzene concentration, flow rate, and biomass loading. The system was modeled mathematically and the kinetic parameters were determined.

Biological removal …

Bond And Fatigue Characteristics Of High-Strength Cement-Based Composites, Somboon Chimaphant

Dissertations

The results of a series of tests on a variety of high strength cementitious composites yield a model from which an empirical equation of general normalized pull-out stress vs. pull-out displacement relationship is developed. A new variable named the "Brittleness Index" is defined and used in the proposed equation. Additionally, the concept of maximum strain is used to predict the fatigue life of high strength concrete.

Three sizes of deformed bars and two types of steel fibers with four different volume fractions were used to observe bond-slip and pull-out characteristics of high strength concrete. The results indicate that the maximum …

Kinematic Synthesis Of Mechanisms For Multiply Separated Positions, Hyoung Jun Kim

Dissertations

The rigid body motion is studied in a combination of finitely and infinitesimally separated positions in planar, spherical, and spatial kinematics. A general new method for determining the locations of points and/or lines in a rigid body moving through finitely and infinitesimally separated positions is developed. These points and/or lines would satisfy the constraints of various types of binary links for planar, spherical, and spatial mechanisms.

A unified form of circle-point curve equation is derived for finitely and multiply separated position problems in planar and spherical motions. A graphical method to construct the circle-point and center-point curves and Ball point …

Anaerobic Biodegradation Of Trichloroethylene With The Addition Of Sugar Using Activated Carbon-Fluidized Beds, Suxan Huang

Dissertations

Anaerobic biodegradation of trichloroethylene (TCE) was carried out in a two-stage granular activated carbon fluidized bed bioreactor. The intermediate products were identified as: dichloroethylene (DCE), vinyl chloride (VC), 1,2-dichloroethane (DCA) and chloroethane (CA). Of the three geometric isomers of DCE, the trans-1,2 dichloroethylene (TDCE) was found to be the most predominant species, The production of DCA suggested a diverted reaction sequence from the conventional sequential reductive dechlorination pathway postulated in the past literature. CA was believed to be a product of VC and/or DCA. The co-substrate glucose was implicated for this reaction specificity. Based on our data and on other's …

Fault-Tolerant Interconnection Networks For Multiprocessor Systems, Hamed Mohamed Nassar

Dissertations

Interconnection networks represent the backbone of multiprocessor systems. A failure in the network, therefore, could seriously degrade the system performance. For this reason, fault tolerance has been regarded as a major consideration in interconnection network design. This thesis presents two novel techniques to provide fault tolerance capabilities to three major networks: the Baseline network, the Benes network and the Clos network.

First, the Simple Fault Tolerance Technique (SFT) is presented. The SFT technique is in fact the result of merging two widely known interconnection mechanisms: a normal interconnection network and a shared bus. This technique is most suitable for networks …

Air Stripping Of Volatile Organic Contaminants Using Rotating Disc Contactor, Kai-Ping Hsueh

Dissertations

Previous studies have suggested that the transfer of VOCs to the atmosphere by air stripping may be a convenient and potentially cost-effective method to remove these compounds from the water. A Rotating Disk Contactor (RDC), similarly to other aeration devices, can provide intimate contact between the VOC-bearing water and air. It is believed that under carefully selected operating conditions, the RDC system are more competitive with packed tower than other aeration methods. The objectives of this study were to evaluate the feasibility of using the RDC to strip VOCs from the contaminated water and to develop a mathematical model to …

Close-Range, Noncontact Distance Measurement By Controlled Image Irradiance, Jaeho Kim

Dissertations

Dimensional measurement or check is a major part of the inspection and quality control in manufacturing. Most of the measurement applications are based on contact methods. While a number of non-contact methods are available, they are limited in accuracy, in flexibility, or in the range of application areas. An optical, close-range, non-contact distance measurement method has been developed for manufacturing and other applications. Based on a simple imaging principle, the method derives the distance information from the power response of a small axial image area, the irradiance of which is controlled by an active controlled illumination of the corresponding object …

Isoparametric Finite Elements For Linear Isotropic Micropolar Plate Bending, Vallanore K. Suresh

Dissertations

Finite element analysis programs for bending of linear isotropic micropolar elasticity are developed in this thesis. Isoparametric two-dimensional and three-dimensional elements are used to solve plate bending problems. Two-dimensional and three-dimensional finite element formulations are developed. Corresponding finite element programs are then developed. Patch tests are performed on the two-dimensional elements. Convergence studies are undertaken for the elements. Several plates are considered to evaluate the finite element scheme. The effects of the coupling factor N and characteristic length 1 are studied. A post processor with graphical display of displacements is developed.

Numerical results obtained for various plates are in good …

Permeability And Volume Change Characeristics Of Bentonite-Sand Mixes In A Contaminant Environment, Yuan-Hsun Wu

Dissertations

This research was conducted to study the characteristics of permeability and volume change of bentonite-sand mixes due to contaminants. The soil specimens consisted of clean sand, bentonite, and fly ash. Test liquids included seven diluted organic and inorganic chemicals and a landfill leachate.

Index tests included liquid limit, expansion, cracking, and sedimentation tests. Expansion tests proved to be the most useful for permeability evaluation in a contaminant environment.

The conventional consolidometer permeameter and flexible wall permeameter proved to be not completely satisfactory for testing soft bentonite mixes. A triple ring permeameter was developed to compensate for the limitations of these …

Thermotropic Liquid Crystalline Polyesters Based On The Monomer Of Poly(Ethylene Terephthalate), Satish Baliga

Dissertations

A series of thermotropic liquid crystalline polyesters were synthesized, based on Bis-hydroxyethyl terephthalate (BHET), para-acetoxybenzoic acid (PAB) and terephthalic acid (TA). Structural studies of these aromatic polyesters using Nuclear Magnetic Resonance (NMR), Infrared Spectroscopy (IR) and X-ray diffraction techniques indicated the existence of substantial amounts of rigid -PAB-PAB- linkages within the mesogenic backbone. Optical study of their melts using Polarizing Microscopy indicated a "threaded" microstructure typical of a nematic mesophase. Morphological rearrangements were found to occur at higher temperatures as was evident from a two-phase structure, one phase speculated to be rich in flexible Poly(ethylene Terephthalate) (PET) segments and the …

Kinetic Study On Pyrolysis Of C6h5cl And M-C6h4cl2 Diluted In H2 : Detailed Reaction Kinetics And Thermodynamic Property Estimation Techniques, Edward Robert Ritter

Dissertations

Thermal reaction studies of dilute mixtures (0.37%) of C6H5Cl in hydrogen and m-C6H4C12 (0.4%) in hydrogen have been performed in tubular flow reactors at various surface to volume ratios, and 1 atm total pressure. Residence times range from 0.02 to 2.5 seconds,with temperatures between 1050 to 1275 K. HCl, C₆H₅Cl, C₆H₆, and carbon solids (C(s)) are observed as the major products; minor products include methane, cyclopentadiene, toluene, naphthalene and biphenyls. Pyrolysis in helium yields significantly less conversion, but more C(s) for similar residence times.

A detailed chemical mechanism is developed to describe …

A Study Of The Effect Of Some Inhibitors On The Corrosion Rates Of Austenitic Stainless Steels In Sulfuric Acid, Shang-Yinn Chiou

Theses

Four sulfur-containing and three nitrogen-containing organic compounds have been tested as inhibitors for four different austenitic stainless steels-SS304, S5316, SS317L, and SS41O-in 10-50 weight% sulfuric acid solutions respectively. Results confirmed that the sulfur-containing compounds were more effective than the nitrogen-containing compounds. The effect of sodium iodide additions on the behaviours of two of the nitrogen-containing compounds was also studied. The synergistic effect caused by the 1 ion was essential for nitrogen-containing compounds as inhibitors in sulfuric acid solution.

Computer Controlled Oxygen Bioreactor, Dinesh Sachdeva

Theses

A computer controlled oxygen bioreactor has been designed to obtain more accurate values for oxygen bioreactor requirements and to optimize oxygen productivity with respect to oxygen concentration. This study solves a specific problem relating to oxygen concentration measurement and bioreactor control. The proposed reactor system is computer controlled to insure a desired oxygen concentration supply to an oxygen consuming reaction or organism. This thesis also explains and illustrates the bioreactor and its computer control system.

The computer controller incorporates oxygen sensing, oxygen measurement and temperature measurement, Electrical circuits have been designed and built for proper signal conditioning, data acquisition, data …

Surfactant Enhanced Scrubbing In An Ejector Venturi Scrubber Of Sulfur Dioxide From Air Exhaust Streams, Humberto Roman

Theses

The objective of this work was to determine the feasibility of applying the Surfactant Enhanced Scrubbing technique to the removal of sulfur dioxide using an ejector venturi scrubber.

Surfactants were chosen according to information from manufacturers. Those surfactants which offered good behavior in the presence of acidic solutions ( low pH ), and anti-corrosion characteristics were tested.

In the first phase, experiments were performed to determine the behavior of the foams in the ejector venturi scrubber. A foam destruction system was used when foaming conditions required it. In the second phase dynamic runs were performed to determine the removal efficiencies …

Adsorption And Desorption Of Chromium On Clayey Soils, Ker-Shu Tan

Theses

Chromium residue waste was produced during sixties in the chromium production process. It was used as construction fill. Problems associated with chromium waste sites include structure distress and surface and groundwater contamination.

The purpose of this study was to investigate the adsorption and desorption of chromium on soil. In order to achieve this purpose, experiments were conducted to study the effect of pH, type of chromium compound, and type of soil on adsorption and desorption.

Experiments were performed on kaolinite, bentonite and sand. In our study, it was found that sand had almost no adsorption for chromium. Kaolinite had less …