Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Institution
- Publication
- Publication Type
Articles 1 - 5 of 5
Full-Text Articles in Entire DC Network
Dry Sliding Tribological Characteristics Of Hard, Flat Materials With Low Surface Roughness, Subrahmanya Mudhivarthi
Dry Sliding Tribological Characteristics Of Hard, Flat Materials With Low Surface Roughness, Subrahmanya Mudhivarthi
USF Tampa Graduate Theses and Dissertations
This thesis focuses on identifying hard material pairs with low roughness, high coefficient of static friction, high wear resistance and high modulus of elasticity, suitable for sliding in dry friction conditions under a normal load. A wide range of materials including various steels, various coatings on tool steels deposited by various deposition techniques and different ceramics were examined and considered for tribological testing. Procedures and sequences were developed for conducting tribology tests on the material pairs. High endurance - low cycle tests were conducted and based on the performance of material pairs with respect to friction, wear and surface roughness …
Admittance Selection For Planar Force-Guided Assembly For Single-Point Contact With Friction, Shuguang Huang, Joseph M. Schimmels
Admittance Selection For Planar Force-Guided Assembly For Single-Point Contact With Friction, Shuguang Huang, Joseph M. Schimmels
Mechanical Engineering Faculty Research and Publications
This paper identifies procedures for selecting the appropriate admittance to achieve reliable planar force-guided assembly for single-point frictional contact cases. A set of conditions that are imposed on the admittance matrix is presented. These conditions ensure that the motion that results from contact reduces part misalignment. We show that, for bounded misalignments, if an admittance satisfies the misalignment-reduction conditions at a finite number of contact configurations and a given coefficient of friction /spl mu//sub M/) then the admittance will also ensure that the conditions are satisfied at all intermediate configurations for all coefficients less than /spl mu//sub M/.
On Friction And Surface Cracking During Sliding Of Ice On Ice, Maurine Montagnat, Erland M. Schulson
On Friction And Surface Cracking During Sliding Of Ice On Ice, Maurine Montagnat, Erland M. Schulson
Dartmouth Scholarship
As a complement to earlier measurements on the friction of both granular fresh-water ice and S2 columnar salt-water ice, new experiments were performed on the friction of S2 columnar fresh-water ice sliding against itself at low velocities (5 × 10−7 to 5 × 10−1 m s−1) and at −10°C, using the same double-shear device as was used earlier. The results showed that under a given set of experimental conditions the kinetic coefficient of friction of S2 fresh-water ice compares favorably with that of the other two variants.The experiments also revealed friction-induced surface cracks and recrystallized grains.These deformation features are explained, …
Fretting Wear Of Metallic Multilayer Films
Fretting Wear Of Metallic Multilayer Films
A.S. Md Abdul Haseeb
Fretting wear behaviour of electrodeposited Cu/Ni multilayer films with 10 and 5 nm thick sublayers has been investigated against a hardened steel ball as the counter body and compared with that of the constituents, Cu and Ni. The wear tests were carried out by using a ball-on-flat geometry at a translation frequency of 8 Hz and slip amplitude of 100 μm. Friction force was recorded on line during the tests. At the end of the tests, the wear scars were examined by laser surface profilometry, scanning electron microscopy and energy dispersive X-ray microanalysis. It has been observed that the frictional …
Design And Fabrication Of A Micro-Bearing Assembly To Study Rotor Friction, Daniel W. Brown
Design And Fabrication Of A Micro-Bearing Assembly To Study Rotor Friction, Daniel W. Brown
Journal of the Microelectronic Engineering Conference
The objective of this investigation was to design and fabricate a metrology tool for measuring the wear in micro-bearings. The critical component of the tool was a silicon test bed consisting of a bearing shaft and a set of microchannels to direct an air stream onto the fins of a micro-rotor assembled onto the bearing shaft. By driving the micro-rotor pneumatically, surface interactions between the bearing and the rotor can be studied over time. The silicon test bed mates to a custom aluminum chuck which has provisions for sealing the test bed and supplying air pressure from an external source. …