Digital Commons Network^™

Removing Aluminum From Solution Using Chelating Compounds And Immobilized Tethered Chelators, Robert A. Yokel, Wesley R. Harris, Christopher D. Spilling, Chang-Guo Zhan

Christopher Spilling

Methods are described for removing aluminum from a solution using novel di- and tripodal compounds as chelators.

Flow-Through Filter To Remove Aluminum From Medical Solutions, Robert A. Yokel, Wesley R. Harris, Christopher D. Spilling, Robert Joseph Kuhn, Vasiliy Paul Abramov, Jason Matthew Lone

Christopher Spilling

A flow through filter assembly includes a trivalent and tetravalent metal ion capturing agent and a flow controller providing a predetermined flow rate which allows capture of the trivalent and tetravalent metal ions by the capturing agent.

In Situ Formation Of Substrate Release Mechanisms For Gas Metal Arc Weld Metal 3-D Printing, Amberlee S. Haselhuhn, Bas Wijnen, Gerald C. Anzalone, Paul G. Sanders, Joshua M. Pearce

Paul Sanders

This study provides an in-depth investigation into low-cost and no-cost substrate release mechanisms that allow gas metal arc weld 3-D printed ER4043 aluminum and ER70S-6 steel parts to be removed from a reusable print substrate with minimal energy. Aluminum oxide, boron nitride, and titanium nitride coatings were evaluated as possible substrate release agents for aluminum printing. Additionally, the in situ formation of substrate release agents such as intermetallics and oxides were tested for both aluminum and steel printing. Testing was performed with a modified Charpy impact tester to remove 3-D printed metal parts from an 1100 aluminum or A36 low …

In Situ Formation Of Substrate Release Mechanisms For Gas Metal Arc Weld Metal 3-D Printing, Amberlee S. Haselhuhn, Bas Wijnen, Gerald C. Anzalone, Paul G. Sanders, Joshua M. Pearce

Joshua M. Pearce

This study provides an in-depth investigation into low-cost and no-cost substrate release mechanisms that allow gas metal arc weld 3-D printed ER4043 aluminum and ER70S-6 steel parts to be removed from a reusable print substrate with minimal energy. Aluminum oxide, boron nitride, and titanium nitride coatings were evaluated as possible substrate release agents for aluminum printing. Additionally, the in situ formation of substrate release agents such as intermetallics and oxides were tested for both aluminum and steel printing. Testing was performed with a modified Charpy impact tester to remove 3-D printed metal parts from an 1100 aluminum or A36 low …

Combinatorial Investigation Of Magnetostriction In Fe-Fa And Fe-Ga-Al, Jason R. Hattrick-Simpers, Dwight Hunter, Corneliu M. Craciunescu, Kyu Sung Jang, Makoto Murakami, James Cullen, Manfred Wuttig, Ichiro Takeuchi, Samuel E. Lofland, Leonid Bendersky, Noble Woo, Robert Bruce Vandover, Toshiya Takahashi, Yasubumi Furuya

Jason R. Hattrick-Simpers

A high-throughput high-sensitivity optical technique for measuringmagnetostriction of thin-film composition-spread samples has been developed. It determines the magnetostriction by measuring the induced deflection of micromachined cantilever unimorph samples. Magnetostrictionmeasurements have been performed on as-deposited Fe–Ga and Fe–Ga–Al thin-film composition spreads. The thin-film Fe–Ga spreads display a similar compositional variation of magnetostriction as bulk. A previously undiscovered peak in magnetostriction at low Ga content was also observed and attributed to a maximum in the magnetocrystalline anisotropy. Magnetostrictive mapping of the Fe–Ga–Al ternary system reveals the possibility of substituting up to 8at.%Al in Fe₇₀Ga₃₀ without significant degradation of magnetostriction.

Fuzzy Logic Based Model For Predicting Surface Roughness Of Machined Al-Si-Cu-Fe Die Casting Alloy Using Different Additives-Turning

Faculty of Engineering University of Malaya

This paper presents a fuzzy logic artificial intelligence technique for predicting the machining performance of Al-Si-Cu-Fe die casting alloy treated with different additives including strontium, bismuth and antimony to improve surface roughness. The Pareto-ANOVA optimization method was used to obtain the optimum parameter conditions for the machining process. Experiments were carried out using oblique dry CNC turning. The machining parameters of cutting speed, feed rate and depth of cut were optimized according to surface roughness values. The results indicated that a cutting speed of 250 m/min, a feed rate of 0.05 mm/rev, and a depth of cut of 0.15 mm …

The Wear Behavior Of Cross-Linked Uhmwpe Under Dry And Bovine Calf Serum-Lubricated Conditions

A.S. Md Abdul Haseeb

The present study was performed to investigate the effects of gamma radiation on the wear behavior of unirradiated and irradiated ultra-high-molecular-weight polyethylene (UHMWPE) against Ti-6Al-4V under dry and lubricated conditions at different applied loads. The UHMWPE specimens were exposed directly to nominal doses of 0, 25, 40, 50, and 100 kGy. Scanning electron microscope (SEM) analysis of the worn surface of UHMWPE and Ti-6Al-4V was performed to understand the mechanism of wear involved between the contact surfaces during wear testing. From the wear test results, there were significant differences between the wear of unirradiated UHMWPE and UHMWPE irradiated at 25, …

Aluminum. History & Metallurgy, Fathi Habashi

Fathi Habashi