Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 5 of 5
Full-Text Articles in Entire DC Network
Eggshells: A Novel Bio-Filler For Intumescent Flame-Retardant Coatings
Eggshells: A Novel Bio-Filler For Intumescent Flame-Retardant Coatings
Faculty of Engineering University of Malaya
The aim of this study was to develop intumescent flame-retardant coatings that incorporate chicken eggshell (CES) waste as a novel eco-friendly bio-filler. Three flame-retardant additives, namely, ammonium polyphosphate phase II, pentaerythritol and melamine were mixed with flame-retardant fillers and acrylic binder to synthesize the intumescent coatings. The fire performance of the coatings was evaluated in accordance with 'BS 476: Part 6-Fire Propagation' and 'BS 476: Part 7-Surface Spread of Flame' test standards. It was found that 4 out of 5 of the coated specimens (B, C, D and E) neither showed surface spread of flame nor any afterglow combustion upon …
Dissimilar Friction Stir Welding Between Polycarbonate And Aa 7075 Aluminum Alloy
Dissimilar Friction Stir Welding Between Polycarbonate And Aa 7075 Aluminum Alloy
Faculty of Engineering University of Malaya
In this paper, the effects of process parameters, such as the tool rotational and traverse speeds, on temperature evolution and the microstructural and mechanical properties of dissimilar friction stir welding between 3 mm thick AA 7075 aluminum alloy and polycarbonate (PC) plates were investigated. The tool rotational and traverse speeds were varied from 3 000 to 3 500 rpm and 50 to 150 mm min(-1), respectively. The joint fabricated at 3 250 rpm and 100 mm min(-1) yielded a highest tensile load of 586 N. Microstructural analysis of the stir zone revealed an interlock phenomenon, the transportation of AA 7075 …
Investigating The Machinability Of Al-Si-Cu Cast Alloy Containing Bismuth And Antimony Using Coated Carbide Insert
Faculty of Engineering University of Malaya
Surface roughness and cutting force are two key measures that describe machined surface integrity and power requirement evaluation, respectively. This investigation presents the effect of melt treatment with addition of bismuth and antimony on machinability when turning Al-11% Si-2% Cu alloy. The experiments are carried out under oblique dry cutting conditions using a PVD TIN-coated insert at three cutting speeds of 70, 130 and 250 m/min, feed rates of 0.05, 0.1, 0.15 mm/rev, and 0.05 mm constant depth of cut. It was found that the Bi-containing workpiece possess the best surface roughness value and lowest cutting force due to formation …
Automated Serviceability Prediction Of Nsm Strengthened Structure Using A Fuzzy Logic Expert System
Automated Serviceability Prediction Of Nsm Strengthened Structure Using A Fuzzy Logic Expert System
Faculty of Engineering University of Malaya
This paper presents a simplified model using a fuzzy logic approach for predicting the serviceability of reinforced concrete (RC) beams strengthened with near surface mounted (NSM) reinforcement. Existing analytical models lack proper formulations for the prediction of deflection and crack width in NSM strengthened beams. These existing models are based on the externally bonded reinforcement (EBR) technique with fiber reinforced polymer (FRP) laminates, which presents certain limitations for application in predicting the behavior of NSM strengthened beams. In this study seven NSM strengthened RC beams were statically tested under four point bending load. The test variables were strengthening material (steel …
Influences Of Flame-Retardant Fillers On Fire Protection And Mechanical Properties Of Intumescent Coatings
Faculty of Engineering University of Malaya
A combination of acrylic binder and flame-retardant ingredients was used to synthesize the solvent-borne intumescent coatings designed for steel substrates. The influences of individual and various combinations of flame-retardant fillers on the fire protection and mechanical properties of the coatings were characterized by using Bunsen burner, thermogravimetric analysis, limiting oxygen index, field emission scanning electron microscopy, freeze thaw cycles, static immersion and pull-off type equipment. It was found that the combination of aluminium hydroxide (Al(OH)(3)) and titanium dioxide (TiO2) has significantly improved the fire protection, thermal stability and water resistance of the coating. This formulation had an LOI value of …