Digital Commons Network^™

Mobile Solar Energy Environmental Control System With Remote Accessibility, Luis S. Garay

Theses and Dissertations

The proposed system, Mobile Solar Energy Environmental Control System with Remote Accessibility (mSEECS w/ RA), is based on the utilization of an already available Energy Storage Unit (ESU) in a Transport Unit System (TUS) to harness solar energy to provide a system to enhance the environment, safety and security of a TUS in a stationary or a mobile state by monitoring and controlling the operation of its onboard systems, and provide remote accessibility to know the state of affairs at any time. To relate to a real world application, the battery (ESU) of a vehicle (TUS) is underutilized …

Development Of Flexible Photo-Mechanoluminescent Polymeric Based Systems, Carlos Hernandez

Theses and Dissertations

The project focuses on the creation of nanofiber systems with enhanced photo-mechanoluminescent response and high mechanical flexibility to further enhance promising optical applications. Lanthanide-Polyvinyl Di-Fluoride fiber systems were created using centrifugal spinning and characterized using SEM, FTIR, XPS, DSC, XRD, and PL. Fibers luminescence response was gotten when induced by ultraviolet light and the application of an impact force.

Security Assessment Of Select Computer Systems Under Distributed Denial Of Service Attacks Performed By Botnets, Hugo Armando Herrera Martinez

Theses and Dissertations

With the passage of time Internet connectivity has been found on more electronic devices than in previous decades. This continuous development may be perceived as a double-edged sword. While the world becomes more Internet-connected and quality of life increases, the lack of proper security protocols in some of these electronic devices permits illegitimate parties to take control of them for their own malicious purposes.

This thesis studies the impact of compromised Internet-connected devices on commonly used server operating systems: Microsoft’s Windows Server 2012 R2 Datacenter, Windows Server 2016 Datacenter, and Apple’s macOS 10.13.6 High Sierra deployed on Apple’s Mac Pro …

Polymeric Pvdf Fibers For Piezoelectric Applications In Energy Harvesting, Misael E. Martinez

Theses and Dissertations

This work focuses on developing and characterizing the piezoelectric response of Cerium doped Polyvinylidene Fluoride (PVDF) fine fibers and the effects of dopants and alignment on the formation of the β-phase and consequently on the piezoelectric performance. Six sets of fiber mats were prepared varying the concentration (2.5–7.5wt%) of Cerium (III) Nitrate-Hexahydrate and Ammonium-Cerium (IV) Sulfate-Dihydrate. Fiber mats were developed using the Forcespinning® technique and the angular velocity and dopant concentration were adjusted to obtain a synergy between fiber yield and fiber diameter. Fourier Transform Infrared Spectroscopy showed a significant enhancement in the PVDF β-phase and inhibition of the non-polar …

Molten-Salt Synthesized Pyrochlore Nanoparticles For Multifunctional Applications, Jose P. Zuniga

Theses and Dissertations

There is a need in the scientific world to design and develop high quality nanomaterials with multifunctional applications. In this work, we explore the molten-salt method (MSS) as a new green method for the synthesis of complex metal oxides. We adjusted all synthesis parameters such as time, temperature and pH to generate an optimum La2Hf2O7 nanoparticle with a well define shape and surface. Activator ions such as Eu3+, Tb3+, Dy3+, Bi3+ and uranium ion (U4+, U6+) were used to monitor its structural and optical behavior effect when doped.

Our results showed effective quantum yield, thermal, pressure stability, near to white …

Biomechanics Of Lower Limb During The Golf Swing Using Opensim Modeling, Andrew B. Butler

Theses and Dissertations

The purpose of this research is to investigate the biomechanics of the lower-limb using an inverse dynamics model. Experimental data, recorded by an integrated Motion Analysis – Force Plate System in the UTRGV Biomechanics Laboratory, is used to determine ground reaction forces and marker trajectories. OpenSim, a graphical musculoskeletal and computational platform, is used to model the body in three dimensions. The human body is modeled as a 12-segment linkage, consisting of 23 degrees-of-freedom and 92 muscles. The experimental data for the Biomechanics Laboratory is imported in OpenSim. Then, joint angles, generalized coordinates & accelerations of lower-limb segments, muscle forces, …

Experimental Study Of Condensation In Different 3d Printed Regenerators In A Thermoacoustic Cooler, Aibek Bekkulov

Theses and Dissertations

Thermoacoustics (TA) deals with the conversion of heat into sound and vice versa. Device that converts heat into acoustic work is called TA heat engine, while the device that transfers energy from a low temperature reservoir to a high temperature one by utilizing acoustic work is called TA cooler. A simple construction of TA cooler includes an acoustic speaker, a resonator tube and a regenerator stack in which the temperature gradient is being imposed. Such a TA cooler has several advantages over traditional compression/expansion cooling machine such as its simplicity of the construction, high reliability and lack of toxic refrigerants. …

Design Of A Bedside Walker-Cane Hybrid To Aid Senior Adults Avoid Falls During Night Walks, Jorge L. Gutierrez

Theses and Dissertations

The objective of this research and development work is to design a device to help senior adults prevent fall during night walks indoors. The problem of elders falling at a night setting was found to be caused by the multiple environmental and medical conditions. The target demographic was found to be seniors from age 65 and older. Several occupational therapists and two physical therapists were consulted to gain knowledge on elders' behavior, possible improvements on current existing devices, and feedback regarding the early prototype built. Several products and patents were researched with a lack of findings on similar products that …

Secondary Resonances Of Electrostatically Actuated Mems Cantilevers, Christopher I. Reyes

Theses and Dissertations

In this work the behavior of micro-electromechanical (MEMS) cantilever resonators is investigated. The cantilever resonators are electrostatically actuated with hard AC voltage resulting in nine distinct resonances cases including super and subharmonic resonances. The amplitude frequency and amplitude voltage bifurcation diagrams are obtained for each of the nine resonance cases. Reduced order models (ROMs) are developed to include one and two modes of vibration. Three different methods are used to solve the ROMs namely 1) the method of multiple scales (MMS), which is a perturbation method used for one mode of vibration, 2) the homotopy analysis method (HAM), which is …

Dehumidification Water Quality Analysis Of The South Texas Gulf Of Mexico, Erik Esteban Castillo

Theses and Dissertations

This project is to introduce a new methodology for environmental research that analyzes humidity from a water treatment perspective. This is done by using a household dehumidifier, which extracts the excess humidity in a given space, to harvest the samples. The dehumidifier was used outside to act as an Atmospheric Water Generator (AWG), which is the process of extracting water from the atmosphere. When AWG is placed near shoreline, then it's classified as a Desalinated Atmospheric Water Generator (DAWG) since it extracts distilled seawater water-vapors. The methodology for DAWG analyzed turbidity in the humidity on SPI, indicating to meet {<.15} TCEQ turbidity water quality standard. The turbidity also showed to have an adverse relation to weather conditions. There is an open market in research on this topic, where the methodology for DAWG can offer answers. This project identifies DAWG as being a sustainable source of potable water for a municipality.

An Evaluation Of Wastewater Pumping Station Facilities Using Statistical Techniques In Analyzing Each For Rehabilitation Design And To Improve The Adverse Environmental Affects, Zenaida S. Guerrero

Theses and Dissertations

The objective of this research project is to develop two evaluation models, one using excel to provide a design criterion for wastewater pumping stations in collecting design parameters and information effecting efficiency and performance of the pumps. Secondly, to develop a linear regression model for these parameters giving a correlation between dependent and independent variables to verify adverse environmental aspects. This study is based in the City of Weslaco, pertaining to the north waste watershed. The parameters collected are age, efficiency, service area, total dynamic head, existing conditions, monthly sanitary sewer over flow work orders, precipitation data, population by service …

Synthesis And Design Of Metals Sulfide/Carbon Composite-Fibers Anodes For Lithium Ion Batteries, Jorge Lopez

Theses and Dissertations

In this study, Forcespinning is used to produce Titanium sulfide (TiS2)/carbon composite fibers for use as lithium-ion battery anodes. The high surface area to volume ratio of the composite fibers can have a high impact on the ionic and electronic conductivity of the active materials leading to improved electrochemical performance of the battery. TiS2 nanoparticles were chosen as the active materials to produce Metal-Li-alloys/C composite fibers due to their high theoretical capacity and low volume change during charge/discharge cycles. The use of a 2-D layered structure of TiS2 nanoparticles in the carbon fiber matrix can greatly accommodate more Li-ions between …

Boron Nitride Thin-Film Deposited By Rf Magnetron Sputtering, Jesus A. Valladares Gonzalez

Theses and Dissertations

Cubic Boron Nitride is considered a superhard material, its thermochemical stability makes it suitable for applications with corrosive environments and high temperatures. C-BN is grown by PDV on Si substrates. The plasma is energized via an RF source to sputter the target. The ion species in the plasma can be described by the classic electrodynamic expression . Plasma temperature is given by T = (6.2836*E/8*k). The sputter is given by the ratio of the heat transfer to the enthalpy of formation , of the target. The Hall Measurement is performed as recommended by NIST. The measurement was performed on a …

Aligning Anatomical Knee Model With Kinematic Experimental Data To Investigate Squat Exercise, Jose Mario Salinas

Theses and Dissertations

A two-dimensional inverse dynamics anatomical model of the human knee was developed by aligning anatomical structures of the knee (taken from x-rays) with kinematic experimental data (collected from motion capture cameras). The mathematical model was used to study the forces related to the tibiofemoral and patellofemoral joints during the squat and knee extension exercises. Forces calculated by the model included: tibiofemoral contact force, patellofemoral contact force, forces generated by cruciate ligaments, quadriceps force, and patellar tendon force. Bone alignment consisted of superimposing the geometric center of the lateral femoral condyle (from x-rays) with the relative instantaneous center of rotation of …

Radiative Heat Transfer Analysis Of Railroad Bearings For Wayside Thermal Detector Optimization, James Alexandro Aranda

Theses and Dissertations

Wayside hot-box detectors (HBDs) are devices that are currently used to evaluate the health of railcar components including bearings, axles, and brakes by monitoring their temperatures. While HBDs have been instrumental in reducing some train derailments in the past few decades, the number of non-verified bearing removals has increased significantly. In general, HBDs tend to underestimate bearing temperatures in both field service and in laboratory testing, which is not surprising considering the simple two-point calibration method that is used to calibrate these devices. Because of this, different calibrations were compared and analyzed including two-point, three-point, and multi-point calibrations. Analysis of …

Improving Thermal-Hydraulic Performance Of Flat-Tube Louver-Fin Heat Exchangers By Eliminating Louver Gap Condensate Bridges, Alan L. Jones

Theses and Dissertations

The air side performance of heat exchangers is a well studied subject. Flat-tube louver-fin heat exchangers experience a decrease in performance when operating in dehumidifying conditions. As water vapor is pulled from the air, water condensate may create blockages between louvers. Flat-tube louver-fin heat exchanger may experience a drop in thermal-hydraulic performance by up to 50% due to blockages. The aim of this study is to make macro scale geometric changes to louver dimensions and eliminate louver condensate bridges. By eliminating louver condensate blockages, the heat exchanger should see an overall gain in thermal performance when compared to current fin …

Local Delivery Of Mesenchymal Stem Cells Expressing Osteogenesis-Inducing Microrna For Bone Tissue Engineering Applications, Marco Antonio Arriaga

Theses and Dissertations

Bone is capable of regenerating autonomously when the injury is small (< 2.5 cm), however, large (> 2.5 cm) or insufficiently vascularized defects require intervention to repair. The overall goal of this project is to contribute towards the development of novel strategies to aid bone tissue regeneration by delivering mesenchymal stem cells expressing microRNAs that induce expression of the runt-related transcription factor 2 (RUNX2). It was determined that porous polycaprolactone (PCL) scaffolds fabricated to have a higher surface area to volume ratio (SVR) (> 80) compared to lower SVR (< 80) were hydrolyzed at a higher rate. Scaffolds fabricated with 80 vol. %/300–500 µm porogen were optimal for cell colonization as higher absorbance of metabolized MTT was detected compared to other scaffold types. From the subset of 5 miRNAs tested, miRNA-26a, miRNA-196 and miRNA-218 demonstrated higher upregulation of RUNX2 gene expression and calcium mineralization and thus, are promising candidates for bone tissue regeneration.

Generalized &Thetas;-Parameter Peakon Solutions For A Cubic Camassa-Holm Model, Michael Rippe

Theses and Dissertations

In this paper we outline a method for obtaining generalized peakon solutions for a cubic Camassa-Holm model originally introduced by Fokas (1995) and recently shown to have a Lax pair representation and bi-Hamiltonian structure by Qiao et al (2012). By considering an amended signum function—denoted sgn &thetas;(x)—where sgn(0) = &thetas; for a constant &thetas;, we explore new generalized peakon solutions for this model. In this context, all previous peakon solutions are of the case &thetas; = 0. Further, we aim to analyze the algebraic quadratic equation resulting from a substitution of the single-peakon ansatz equipped with our amended …

A Systematic Approach To High Blood Pressure Risk Analysis And Healthcare Cost Reduction In Young Adults [Metodología Sistemática Para El Análisis De Riesgo Y Reducción De Costos De Servicios Médicos De Hipertensión En Adultos Jóvenes], Francisco Rafael Torres Diaz

Theses and Dissertations

The purpose of this research is to utilize publicly available data to estimate the current rate of occurrence of undiagnosed High Blood Pressure (HBP) in young adults (18 to 24 years old) and the out-of-pocket healthcare expenses associated with complications of HBP, to provide feasible alternatives to mitigate the effects on a region's economy. This has been done by building a Risk Factor Simulation Model that utilizes known HBP risk factors’ correlation to HBP, insurance coverage data, and rate of diagnosis to formulate the average Risk Factor Value for a region, which through an Annual Expected Cost Function estimates the …

Analysis Of Flash In Injection Molding Using Flow Simulation And Design Of Experiments, Claudia Lizette Lopez

Theses and Dissertations

This study presents a method of detecting flash by using flow simulation along with the mold processing conditions and the DOE analysis values from all input and output parameters that will be calculated. All of this would be completed in order to compare and verify the DOE and simulation results and find out if it can be applied to an actual live production molded part, in this case, the Leap char ribbon. This paper will also describe the scrap issue that is presently happening on this molded part, and what are the options that there is in order to find …

Forcespinning Of Metal Oxides And Metal Sulfides And Their Applications As Alternative Anode Materials For Lithium-Ion And Sodium-Ion Batteries, Alejandra Valdez

Theses and Dissertations

Molybdenum-Oxide/Carbon (MoO2/C) composite nanofibers were synthesized using Forcespinning method and subsequent heat treatment, for use as anode materials for lithium-ion batteries. Due to the layered structure of MoO2, the composite nanofibers are very promising for use as anode material for LIBs. The MoO2/C composite fiber anodes exhibit good electrochemical performance and cycling stability.

Design And Characterization Of An Affordable Laser Communication System, Andrea Tellez

Theses and Dissertations

Over the last decades, an exponential growth in communication demand has been observed. Radio Frequency (RF) band has been one of the most used bandwidths for data transmission in the world. Given the influence and the continuous growth of communication technology, the RF spectrum is overpopulated. More efficient systems are necessary to meet the communication needs of this generation. A change to optical bandwidth is the most practical alternative to deal with the congestion of radio frequency.

The aim of this thesis is to present the features of Free Space Optical links with off-the-shelf components. A description of how these …

Antimicrobial Properties And Characterization Of Polymer/Composite Nanofibers, David De La Garza

Theses and Dissertations

Pathogenic bacteria have been the cause of many illnesses worldwide due to their rapid growth and reproduction in food and water. Bacteria-resistant antibiotics and kidney complications due to overuse of antibiotics has remained a large public health concern. The goal of this research project was to find an alternative by producing nanofibers that inhibit microbial growth utilizing Forcespinning technology. The Forcespinning of poly(acrylic acid) (PAA) with Single Wall Carbon Nanotubes functionalized with OH (SWCNT-OH) and Ag + flakes were carried out on solutions with different concentrations. Scanning electron microscopy was used to view fiber morphology and investigate the average nanofiber …

Lead Doped Carbon Nanofibers In Li-Ion Batteries, Omar Torres

Theses and Dissertations

Lead acid batteries have been a very reliable rechargeable battery since its inception in the mid-1800s. Lithium-Ion batteries have been sought out for their light-weight and capacity of holding large amounts of energy in a small amount of space. Few studies have been conducted in the use of lead in lithium-ion batteries.

In this thesis, lead-doped carbon nanofibers were produced by using the Forcespinning® method and used as an anode on a lithium-ion battery. The morphology, material characterization and thermal properties of the anode material were analyzed using the Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), Thermogravimetric Analysis …

Fibers For Skin Regeneration, Astrid Michelle Rodriguez Negron

Theses and Dissertations

This thesis presents the successful development of biocompatible Polyvinyl Butyral (PVB), PVB/Polylysine and PVB/Tannic Acid (TA)/Polylysine fibers from an ethanol solution, Polyhydroxybutyrate (PHB), PHB/Polylysine, PHB/TA/Polylysine fibers from a chloroform solution and Chitosan (CH)/Pullulan (PL)/TA and CH/PL/TA/Polylysine fibers from an aqueous solution. The fibers were mass produced utilizing the Forcespinning® (FS) technology. The morphology of the fibers was characterized using a scanning electron microscope (SEM) and the fibers average diameter was calculated. The thermal properties of the fibers were characterized using a thermogravimetric analyzer (TGA) and a differential scanning calorimeter (DSC). The antibacterial activity of the fibers was assessed using against …

Simplification Of Eeg Signal Extraction, Processing, And Classification Using A Consumer-Grade Headset To Facilitate Student Engagement In Bci Research, Jesus D. Rodriguez

Theses and Dissertations

Brain-computer interfaces (BCIs) are an emerging technology that leverage neurophysiological signals as input to computing systems. By circumventing the reliance on traditional input methods (e.g., mouse and keyboard), BCIs show a promising alternative interaction modality for people with disabilities. Advances in BCI research have further inspired a range of novel applications, such as the use of neurophysiological signals as passive input (e.g., to detect and reduce operator workload when managing multiple machines). BCIs have also emerged as a tool for student engagement due to the intrinsic interdisciplinarity of the technology, which spans the fields of computer science, electrical engineering, neuroscience, …

Design Of A Multidirectional Wear Testing Device For Simulating Wear Of Biocompatible Materials Used In Joint Implants, Carlos A. Rodriguez Betancourth

Theses and Dissertations

In the present work, a novel multidirectional pin-on-disc wear testing device designated CNC-POD (computer-numerical-control pin-on-disc) capable of replicating the cross-shear motions experienced by a prosthesis in vivo was designed and developed in the UTRGV in order to evaluate the wear resistance of new biomaterials. The CNC-POD consists of six temperature-controlled pin-on-disc stations mounted on a two-axis CNC table (X-Y). Each pin-on-disc station is load-programmable up to 510 Newtons (115 pounds). The CNC table allows the machine to reproduce a wide range of 2D patterns in millimeter scale on the six stations under a specific load. Friction force is measured during …

The Effect Of Heat Generation In The Railroad Bearing Thermoplastic Elastomer Suspension Element On The Thermal Behavior Of Railroad Bearing Assembly, Oscar Osvaldo Rodriguez

Theses and Dissertations

Understanding the internal heat generation of the railroad bearing elastomer suspension element during operation is essential to predict its dynamic response and structural integrity, as well as to predict the thermal behavior of the complete railroad bearing assembly including the bearing adapter. The latter is essential for sensor selection and placement within the adapter (e.g., typical temperature sensors have operating ranges of up to 125°C or 257°F). The internal heat generation is a function of the loss modulus, strain, and frequency. Based on experimental studies, estimations of internally generated heat within the thermoplastic elastomer pad were obtained. The calculations show …

The Use Of Mixed Organic/Ionic Liquid Electrolytes With Forcespun Metal Oxides/Carbon Microfiber Electrodes In Lithium Ion Batteries, Jahaziel Villarreal

Theses and Dissertations

Conventional Lithium-Ion Battery (LIB) electrolytes have serious safety concerns because of highly flammability. In order to mitigate this drawback, alternative electrolytes with low volatility and non-flammable need to be synthesis. Ionic liquids (ILs) and mixed organic ionic liquid electrolytes (MOILEs) are the most suitable replacement for the highly flammable commercial organic electrolytes. In this academic investigation, a new perspective on the electrochemical performance of the ionic liquid EMI-TFSI as an alternate non-flammable electrolyte. In parallel, the use of Forcespun nanofibers as binder-free anodes will be analyzed to further improve overall electrochemical performance.

Multifunctional Carbon Systems (Interlaminated Carbon Nanofiber Mats/ Carbon Nanotubes Polymer Composites), Homero Gonzalez Guardiola

Theses and Dissertations

Carbon nanomaterials have been an attractive topic within diverse industrial sectors given their outstanding properties for decades. One of the properties that has been calling attention is it’s shielding effectiveness (SE) for electromagnetic interference (EMI), because of the constant race of improving portable electronic and wireless communication devices among other applications. The present study, analyzes the properties of interlaminated Carbon Nanofiber (CNF) mats/Carbon Nanotubes (CNT) polymer composites, emphasizing in its capability to shield EMI. The CNF mats were developed with Polyvinyl alcohol (PVA) as a precursor and by means of the Forcespinning® technology which uses centrifugal force to create fibers …