Open Access. Powered by Scholars. Published by Universities.®

Digital Commons Network

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 30 of 44

Full-Text Articles in Entire DC Network

Generalized Ultrasonic Scattering Model For Arbitrary Transducer Configurations, Andrea P. Arguelles, Joseph A. Turner Dec 2019

Generalized Ultrasonic Scattering Model For Arbitrary Transducer Configurations, Andrea P. Arguelles, Joseph A. Turner

Mechanical & Materials Engineering Faculty Publications

Ultrasonic scattering in polycrystalline media is directly tied to microstructural features. As a result, modeling efforts of scattering from microstructure have been abundant. The inclusion of beam modeling for the ultrasonic transducers greatly simplified the ability to perform quantitative, fully calibrated experiments. In this article, a theoretical scattering model is generalized to allow for arbitrary source and receiver configurations, while accounting for beam behavior through the total propagation path. This extension elucidates the importance and potential of out-of-plane scattering modes in the context of microstructure characterization. The scattering coefficient is explicitly written for the case of statistical isotropy and ellipsoidal ...


Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laserwire-Based Directed Energy Deposition, Brian T. Gibson, Bradley S. Richardson, Tayler W. Undermann, Lonnie J. Love Oct 2019

Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laserwire-Based Directed Energy Deposition, Brian T. Gibson, Bradley S. Richardson, Tayler W. Undermann, Lonnie J. Love

Mechanical & Materials Engineering Faculty Publications

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser wire-based directed energy deposition is demonstrated with a novel modification, i.e., site-specific changes to the controller setpoint were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary three-dimensional (3D) printed component geometry. The present work shows that, through this technique, it is possible to print a ...


Effect Of Silica Fume In Concrete On Mechanical Properties And Dynamic Behaviors Under Impact Loading, Shijun Zhao, Qing Zhang Oct 2019

Effect Of Silica Fume In Concrete On Mechanical Properties And Dynamic Behaviors Under Impact Loading, Shijun Zhao, Qing Zhang

Mechanical & Materials Engineering Faculty Publications

The effect of silica fume (SF) in concrete on mechanical properties and dynamic behaviors was experimentally studied by split Hopkinson pressure bar (SHPB) device with pulse shaping technique. Three series of concrete with 0, 12%, and 16% SF as a cement replacement by weight were produced firstly. Then the experimental procedure for dynamic tests of concrete specimens with SF under a high loading rate was presented. Considering the mechanical performance and behaviors of the concrete mixtures, those tests were conducted under five different impact velocities. The experimental results clearly show concrete with different levels of SF is a strain-rate sensitive ...


System And Method For Sensing Wind Flow Passing Over Complex Terrain, Saleh Nabi, Piyush Grover, Mithu Debnath Sep 2019

System And Method For Sensing Wind Flow Passing Over Complex Terrain, Saleh Nabi, Piyush Grover, Mithu Debnath

Mechanical & Materials Engineering Faculty Publications

A wind flow sensing system determines a first approximation of the velocity field at each of the altitudes by simulating computational fluid dynamics ( CFD ) of the wind flow with operating parameters reducing a cost function of a weighted combination of errors , determines a horizontal derivative of vertical velocity at each of the altitudes from the first approximation of the velocity fields , and determines a second approximation of the velocity fields using geometric relationships between a velocity field for each of the altitudes , projections of the measurements of radial velocities on the three - dimensional axes , and the horizontal derivative of vertical ...


Multi-Agent Control System And Method, Piyush Grover, Karthik Elamvazhuthi Sep 2019

Multi-Agent Control System And Method, Piyush Grover, Karthik Elamvazhuthi

Mechanical & Materials Engineering Faculty Publications

Motion of multiple agents with identical non - linear dynamics is controlled to change density of the agents from the initial to the final density . A first control problem is formulated for optimizing a control cost of changing density of the agents from the initial density to the final density subject to dynamics of the agents in a density space . The first control problem , which is a non - linear non - convex problem over a multi - agent control and a density of the agents , is trans formed into a second control problem over the density of the agents and a product of ...


3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan Sep 2019

3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan

Mechanical & Materials Engineering Faculty Publications

3D printing/bioprinting are promising techniques to fabricate scaffolds with well controlled and patient-specific structures and architectures for bone tissue engineering. In this study, we developed a composite bioink consisting of silk fibroin (SF), gelatin (GEL), hyaluronic acid (HA), and tricalcium phosphate (TCP) and 3D bioprinted the silk fibroin-based hybrid scaffolds. The 3D bioprinted scaffolds with dual crosslinking were further treated with human platelet-rich plasma (PRP) to generate PRP coated scaffolds. Live/Dead and MTT assays demonstrated that PRP treatment could obviously promote the cell growth and proliferation of human adipose derived mesenchymal stem cells (HADMSC). In addition, the treatment ...


3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Duan Bin Sep 2019

3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Duan Bin

Mechanical & Materials Engineering Faculty Publications

3D printing/bioprinting are promising techniques to fabricate scaffolds with well controlled and patient-specific structures and architectures for bone tissue engineering. In this study, we developed a composite bioink consisting of silk fibroin (SF), gelatin (GEL), hyaluronic acid (HA), and tricalcium phosphate (TCP) and 3D bioprinted the silk fibroin-based hybrid scaffolds. The 3D bioprinted scaffolds with dual crosslinking were further treated with human platelet-rich plasma (PRP) to generate PRP coated scaffolds. Live/Dead and MTT assays demonstrated that PRP treatment could obviously promote the cell growth and proliferation of human adipose derived mesenchymal stem cells (HADMSC). In addition, the treatment ...


Interface Effects On He Ion Irradiation In Nanostructured Materials, Wenfan Yang, Jingyu Pang, Shijian Zheng, Jian Wang, Xinghang Zhang, Xiuliang Ma Aug 2019

Interface Effects On He Ion Irradiation In Nanostructured Materials, Wenfan Yang, Jingyu Pang, Shijian Zheng, Jian Wang, Xinghang Zhang, Xiuliang Ma

Mechanical & Materials Engineering Faculty Publications

In advanced fission and fusion reactors, structural materials suffer from high dose irradiation by energetic particles and are subject to severe microstructure damage. He atoms, as a byproduct of the (n) transmutation reaction, could accumulate to form deleterious cavities, which accelerate radiation-induced embrittlement, swelling and surface deterioration, ultimately degrade the service lifetime of reactor materials. Extensive studies have been performed to explore the strategies that can mitigate He ion irradiation damage. Recently, nanostructured materials have received broad attention because they contain abundant interfaces that are efficient sinks for radiation-induced defects. In this review, we summarize and analyze the current understandings ...


The Linc Complex, Mechanotransduction, And Mesenchymal Stem Cell Function And Fate, Tasneem Bouzid, Eunju Kim, Brandon D. Riehl, Amir Monemian Esfahani, Jordan Rosebohm, Ruiguo Yang, Bin Duan, Jung Yul Lim Aug 2019

The Linc Complex, Mechanotransduction, And Mesenchymal Stem Cell Function And Fate, Tasneem Bouzid, Eunju Kim, Brandon D. Riehl, Amir Monemian Esfahani, Jordan Rosebohm, Ruiguo Yang, Bin Duan, Jung Yul Lim

Mechanical & Materials Engineering Faculty Publications

Mesenchymal stem cells (MSCs) show tremendous promise as a cell source for tissue engineering and regenerative medicine, and are understood to be mechanosensitive to external mechanical environments. In recent years, increasing evidence points to nuclear envelope proteins as a key player in sensing and relaying mechanical signals in MSCs to modulate cellular form, function, and differentiation. Of particular interest is the Linker of Nucleoskeleton and Cytoskeleton (LINC) complex that includes nesprin and SUN. In this review, the way in which cells can sense external mechanical environments through an intact nuclear envelope and LINC complex proteins will be briefly described. Then ...


On The Measurement Of Energy Dissipation Of Adhered Cells With The Quartz Microbalance With Dissipation Monitoring, Amir Monemian Esfahani, Weiwei Zhao, Jennifer Y. Chen, Changjin Huang, Ning Xi, Jun Xi, Ruiguo Yang Aug 2019

On The Measurement Of Energy Dissipation Of Adhered Cells With The Quartz Microbalance With Dissipation Monitoring, Amir Monemian Esfahani, Weiwei Zhao, Jennifer Y. Chen, Changjin Huang, Ning Xi, Jun Xi, Ruiguo Yang

Mechanical & Materials Engineering Faculty Publications

We previously reported the finding of a linear correlation between the change of energy dissipation (ΔD) of adhered cells measured with the quartz crystal microbalance with dissipation monitoring (QCM-D) and the level of focal adhesions of the cells. To account for this correlation, we have developed a theoretical framework for assessing the ΔD-response of adhered cells. We rationalized that the mechanical energy of an oscillating QCM-D sensor coupled with a cell monolayer is dissipated through three main processes: the interfacial friction through the dynamic restructuring (formation and rupture) of cell-extracellular matrix (ECM) bonds, the interfacial viscous damping by the liquid ...


Observations Of Shear Stress Effects On Staphylococcus Aureus Biofilm Formation, Erica Sherman, Kenneth W. Bayles, Derek Moormeir, Jennifer Endres, Timothy Wei Jul 2019

Observations Of Shear Stress Effects On Staphylococcus Aureus Biofilm Formation, Erica Sherman, Kenneth W. Bayles, Derek Moormeir, Jennifer Endres, Timothy Wei

Mechanical & Materials Engineering Faculty Publications

Staphylococcus aureus bacteria form biofilms and distinctive microcolony or “tower” structures that facilitate their ability to tolerate antibiotic treatment and to spread within the human body. The formation of microcolonies, which break off, get carried downstream, and serve to initiate biofilms in other parts of the body, is of particular interest here. It is known that flow conditions play a role in the development, dispersion, and propagation of biofilms in general. The influence of flow on microcolony formation and, ultimately, what factors lead to microcolony development are, however, not well understood. The hypothesis being examined is that microcolony structures form ...


Modeling Thermal And Mechanical Cancellation Of Residual Stress From Hybrid Additive Manufacturing By Laser Peening, Guru Madireddy, Chao Li, Jingfu Liu, Michael P. Sealy Jul 2019

Modeling Thermal And Mechanical Cancellation Of Residual Stress From Hybrid Additive Manufacturing By Laser Peening, Guru Madireddy, Chao Li, Jingfu Liu, Michael P. Sealy

Mechanical & Materials Engineering Faculty Publications

Additive manufacturing (AM) of metals often results in parts with unfavorable mechanical properties. Laser peening (LP) is a high strain rate mechanical surface treatment that hammers a workpiece and induces favorable mechanical properties. Peening strain hardens a surface and imparts compressive residual stresses improving the mechanical properties of a material. This work investigates the role of LP on layer-by-layer processing of 3D printed metals using finite element analysis. The objective is to understand temporal and spatial residual stress development after thermal and mechanical cancellation caused by cyclically coupling printing and peening. Results indicate layer peening frequency is a critical process ...


Method For Fabrication Of A Soft-Matter Printed Circuit Board, Carmel Majidi, Tong Lu, Eric J. Markvicka Jul 2019

Method For Fabrication Of A Soft-Matter Printed Circuit Board, Carmel Majidi, Tong Lu, Eric J. Markvicka

Mechanical & Materials Engineering Faculty Publications

A fabrication process for soft - matter printed circuit boards is disclosed in which traces of liquid - phase Ga - In eutectic ( eGaIn ) are patterned with UV laser micromachining ( UVLM ) . The terminals of the elastomer - sealed LM circuit connect to the surface mounted chips through vertically aligned columns of eGaIn - coated ferromagnetic micro spheres that are embedded within an interfacial elastomer layer .


Wearable Devices For Single-Cell Sensing And Transfection, Lingqian Chang, Yu-Chieh Wang, Faheem Ershad, Ruiguo Yang, Cunjiang Yu, Yubo Fan May 2019

Wearable Devices For Single-Cell Sensing And Transfection, Lingqian Chang, Yu-Chieh Wang, Faheem Ershad, Ruiguo Yang, Cunjiang Yu, Yubo Fan

Mechanical & Materials Engineering Faculty Publications

Wearable healthcare devices are mainly used for biosensing and transdermal delivery. Recent advances in wearable biosensors allow for long-term and real-time monitoring of physiological conditions at a cellular resolution. Transdermal drug delivery systems have been further scaled down, enabling wide selections of cargo, from natural molecules (e.g., insulin and glucose) to bioengineered molecules (e.g., nanoparticles). Some emerging nanopatches show promise for precise single-cell gene transfection in vivo and have advantages over conventional tools in terms of delivery efficiency, safety, and controllability of delivered dose. In this review, we discuss recent technical advances in wearable micro/nano devices with ...


Influence Of Metal Additives On Microstructure And Properties Of Amorphous Metal–Sioc Composites, Kaisheng Ming, Qing Su, Chao Gu, Dongyue Xie, Yongqiang Wang, Michael Nastasi, Jian Wang Apr 2019

Influence Of Metal Additives On Microstructure And Properties Of Amorphous Metal–Sioc Composites, Kaisheng Ming, Qing Su, Chao Gu, Dongyue Xie, Yongqiang Wang, Michael Nastasi, Jian Wang

Mechanical & Materials Engineering Faculty Publications

Strong, ductile, and irradiation-tolerant structural materials are in urgent demand for improving the safety and efficiency of advanced nuclear reactors. Amorphous ceramics could be promising candidates for high irradiation tolerance due to thermal stability and lack of crystal defects. However, they are very brittle due to plastic flow instability. Here, we realized enhanced plasticity of amorphous ceramics through compositional and microstructural engineering. Two metal–amorphous ceramic composites, Fe-SiOC and Cu-SiOC, were fabricated by magnetron sputtering. Iron atoms are preferred to form uniformly distributed nano-sized Fe-rich amorphous clusters, while copper atoms grow non-uniformly distributed nano-crystalline Cu particles. The Fe-SiOC composite exhibits ...


Biomechanical Foot Guidance Linkage, Carl Nelson, Cale J. Stolle, Judith M. Burnfield Apr 2019

Biomechanical Foot Guidance Linkage, Carl Nelson, Cale J. Stolle, Judith M. Burnfield

Mechanical & Materials Engineering Faculty Publications

A gait replication apparatus can include a scalable mechanical mechanism configured to replicate different gaits . The scalable mechanical mechanism can include , for example , a four - bar linkage , a pantograph , a cam / Scotch - yoke mechanism , and so forth . In some embodiments , the mechanical mechanism includes a beam rotating about an axis passing proximate to its center , with a foot pedal slidably coupled with the beam , and a timing chain / belt or cable pulley - pair coupled with the foot pedal and looped about the beam . A method can include decomposing a foot path defined by Cartesian coordinates into polar coordinates , and providing ...


Soft , Multilayered Electronics For Wearable Devices And Methods To Produce The Same, Carmel Majidi, Michael D. Bartlett, Eric J. Markvicka Mar 2019

Soft , Multilayered Electronics For Wearable Devices And Methods To Produce The Same, Carmel Majidi, Michael D. Bartlett, Eric J. Markvicka

Mechanical & Materials Engineering Faculty Publications

Disclosed herein is an efficient fabrication approach to create highly customizable wearable electronics through rapid laser machining and adhesion - controlled soft materials assembly . Well - aligned , multi - layered materials can be created from 2D and 3D elements that stretch and bend while seamlessly integrating with rigid components such as micro chip integrated circuits ( IC ) , discrete electrical components , and interconnects . These techniques are applied using commercially available materials . These materials and methods enable custom wearable electronics while offering versatility in design and functionality for a variety of bio - monitor ing applications .


Gastrointestinal Sensor Implantation System, Benjamin Terry, Weston Lewis, Wanchuan Xie, Pengbo Li, Alfred Tsubaki Mar 2019

Gastrointestinal Sensor Implantation System, Benjamin Terry, Weston Lewis, Wanchuan Xie, Pengbo Li, Alfred Tsubaki

Mechanical & Materials Engineering Faculty Publications

A gastrointestinal ( GI ) sensor deployment device is dis closed . In implementations , the sensor deployment device includes an orally - administrable capsule with a tissue cap ture device removably coupled to the orally - administrable capsule . The tissue capture device includes a plurality of fasteners for connecting the tissue capture device to GI tissue within a body . A biometric sensor is coupled to the tissue capture device for continuous or periodic monitoring of the GI tract of the body at the GI tissue attachment location . A chamber within the orally - administrable capsule is configured to draw gastrointestinal tissue towards the plurality of fasteners ...


Interactions Between Dislocations And Three-Dimensional Annealing Twins In Face Centered Cubic Metals, Yanxiang Liang, Xiaofang Yang, Mingyu Gong, Guisen Liu, Qing Liu, Jian Wang Mar 2019

Interactions Between Dislocations And Three-Dimensional Annealing Twins In Face Centered Cubic Metals, Yanxiang Liang, Xiaofang Yang, Mingyu Gong, Guisen Liu, Qing Liu, Jian Wang

Mechanical & Materials Engineering Faculty Publications

Annealing twins often form in metals with a face centered cubic structure during thermal and mechanical processing. Here, we conducted molecular dynamic (MD) simulations for copper and aluminum to study the interaction processes between {1 1 1}1/2 <1 1 0> dislocations and a three-dimensional annealing twin. Twin boundaries are characterized with Σ3{1 1 1} coherent twin boundaries (CTBs) and Σ3{1 1 2} incoherent twin boundaries (ITBs). MD results revealed that dislocation-ITB interactions affect slip transmission for a dislocation crossing CTBs, facilitating the nucleation of Lomer dislocation.


Strength And Plasticity Of Amorphous Silicon Oxycarbide, Kaisheng Ming, Chao Gu, Qing Su, Yongqiang Wang, Arezoo Zare, Don A. Lucca, Michael Nastasi, Jian Wang Jan 2019

Strength And Plasticity Of Amorphous Silicon Oxycarbide, Kaisheng Ming, Chao Gu, Qing Su, Yongqiang Wang, Arezoo Zare, Don A. Lucca, Michael Nastasi, Jian Wang

Mechanical & Materials Engineering Faculty Publications

Amorphous SiOC films were synthesized by magnetron sputtering at room temperature with/without radio frequency (RF) bias and further improved in terms of mechanical properties by ion irradiation. As-deposited SiOC films without RF bias exhibit catastrophic failure at a low stress and strain, which is ascribed to microstructural heterogeneities associated with the formation of voids during deposition, as evidenced by transmission electron microscopy. Ion irradiation unifies microstructure accompanied with eliminating the voids, resulting in a simultaneously increase in strength and plasticity (ultimate strength of 5–7 GPa and the strain to shear instability of over 20%). Homogeneous microstructures are demonstrated ...


Hemodynamic Interference Of Serial Stenoses And Its Impact On Ffr And Ifr Measurements, Siyeong Ju, Linxia Gu Jan 2019

Hemodynamic Interference Of Serial Stenoses And Its Impact On Ffr And Ifr Measurements, Siyeong Ju, Linxia Gu

Mechanical & Materials Engineering Faculty Publications

The hemodynamic interference of serial stenoses poses challenges for identifying the functional severity using the fractional flow reserve (FFR) method. The instantaneous wave-free ratio (iFR), i.e., the distal-to-proximal pressure ratio at 75% of diastole, was recently proposed to overcome the disadvantages of the FFR. However, the underlying mechanism remained ambiguous due to the lack of quantitative definition of hemodynamic interference. The objective of this study is to quantitatively define the hemodynamic interference and then examine its role on the FFR and iFR measurements. Pressure distributions, velocity fields, and Q-criterion which identifies vortices, were obtained through the computational fluid dynamics ...


Unveiling The Operation Mechanism Of Layered Perovskite Solar Cells, Yun Lin, Yanjun Fang, Jingjing Zhao, Yuchuan Shao, Samuel J. Stuard, Masrur Morshed Nahid, Harald Ade, Qi Wang, Jeffrey E. Shield, Ninghao Zhou, Andrew M. Moran, Jinsong Huang Jan 2019

Unveiling The Operation Mechanism Of Layered Perovskite Solar Cells, Yun Lin, Yanjun Fang, Jingjing Zhao, Yuchuan Shao, Samuel J. Stuard, Masrur Morshed Nahid, Harald Ade, Qi Wang, Jeffrey E. Shield, Ninghao Zhou, Andrew M. Moran, Jinsong Huang

Mechanical & Materials Engineering Faculty Publications

Layered perovskites have been shown to improve the stability of perovskite solar cells while its operation mechanism remains unclear. Here we investigate the process for the conversion of light to electrical current in high performance layered perovskite solar cells by examining its real morphology. The layered perovskite films in this study are found to be a mixture of layered and three dimensional (3D)-like phases with phase separations at micrometer and nanometer scale in both vertical and lateral directions. This phase separation is explained by the surface initiated crystallization process and the competition of the crystallization between 3D-like and layered ...


Predictive Peridynamic 3d Models Of Pitting Corrosion In Stainless Steel With Formation Of Lacy Covers, Siavash Jafarzadeh, Florin Bobaru, Ziguang Chen Jan 2019

Predictive Peridynamic 3d Models Of Pitting Corrosion In Stainless Steel With Formation Of Lacy Covers, Siavash Jafarzadeh, Florin Bobaru, Ziguang Chen

Mechanical & Materials Engineering Faculty Publications

In this work, the peridynamic corrosion model is used for 3D simulation of pitting corrosion in stainless steel. Models for passivation and salt layer formation are employed to predict detailed characteristics of pit growth kinetic in stainless steels, such as lacy cover formation on top of the pit, and the diffusion-controlled regime at the pit bottom. The model is validated against an experimentally grown pit on 316L stainless steel in NaCl solution. Lacy covers in this model are formed autonomously during the simulation process. They are remarkably similar to the covers observed on top of the real pits.


Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing, Michael P. Sealy, Haitham Hadidi, Cody Kanger, X. L. Yan, Bai Cui, J. A. Mcgeough Jan 2019

Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing, Michael P. Sealy, Haitham Hadidi, Cody Kanger, X. L. Yan, Bai Cui, J. A. Mcgeough

Mechanical & Materials Engineering Faculty Publications

Cold working individual layers during additive manufacturing (AM) by mechanical surface treatments, such as peening, effectively “prints” an aggregate surface integrity that is referred to as a glocal (i.e., local with global implications) integrity. Printing a complex, pre-designed glocal integrity throughout the build volume is a feasible approach to improve functional performance while mitigating distortion. However, coupling peening with AM introduces new manufacturing challenges, namely thermal cancellation, whereby heat relaxes favorable residual stresses and work hardening when printing on a peened layer. Thus, this work investigates glocal integrity formation from cyclically coupling LENS® with laser peening on 420 stainless ...


Three-Dimensional Character Of The Deformation Twin In Magnesium, Y. Liu, P.Z. Tang, M.Y. Gong, R.J. Mccabe, J. Wang, C.N. Tome Jan 2019

Three-Dimensional Character Of The Deformation Twin In Magnesium, Y. Liu, P.Z. Tang, M.Y. Gong, R.J. Mccabe, J. Wang, C.N. Tome

Mechanical & Materials Engineering Faculty Publications

Deformation twins are three-dimensional domains, traditionally viewed as ellipsoids because of their two-dimensional lenticular sections. In this work, we performed statistical analysis of twin shapes viewing along three orthogonal directions: the ‘dark side’ (DS) view along the twin shear direction (η1), the twinning plane normal (TPN) view (k1) and the ‘bright side’ (BS) view along the direction λ(=k1 × η1). Our electron back-scatter diffraction results show that twins in the DS and BS views normally exhibit a lenticular shape, whereas they show an irregular shape in the TPN view. Moreover, the findings in the TPN view revealed that twins grow ...


9r Phase Enabled Superior Radiation Stability Of Nanotwinned Cu Alloys Via In Situ Radiation At Elevated Temperature, Cuncai Fan, Dongyue Xie, Jin Li, Zhongxia Shang, Youxing Chen, Sichuang Xue, Jian Wang, Meimei Li, Anter El-Azab, Haiyan Wang, Xinghang Zhang Jan 2019

9r Phase Enabled Superior Radiation Stability Of Nanotwinned Cu Alloys Via In Situ Radiation At Elevated Temperature, Cuncai Fan, Dongyue Xie, Jin Li, Zhongxia Shang, Youxing Chen, Sichuang Xue, Jian Wang, Meimei Li, Anter El-Azab, Haiyan Wang, Xinghang Zhang

Mechanical & Materials Engineering Faculty Publications

Nanotwinned metals exhibit outstanding radiation tolerance as twin boundaries effectively engage, transport and eliminate radiation-induced defects. However, radiation-induced detwinning may reduce the radiation tolerance associated with twin boundaries, especially at elevated temperatures. Here we show, via in-situ Kr ion irradiation inside a transmission electron microscope, that 3 at. % Fe in epitaxial nanotwinned Cu (Cu97Fe3) significantly improves the thermal and radiation stability of nanotwins during radiation up to 5 displacements-per-atom at 200 °C. Such enhanced stability of nanotwins is attributed to a diffuse 9R phase resulted from the dissociation of incoherent twin boundaries in nanotwinned Cu97Fe ...


Design Rules For Additive Manufacturing – Understanding The Fundamental Thermal Phenomena To Reduce Scrap, M. Reza Yavari, Kevin D. Cole, Prahalada K. Rao Jan 2019

Design Rules For Additive Manufacturing – Understanding The Fundamental Thermal Phenomena To Reduce Scrap, M. Reza Yavari, Kevin D. Cole, Prahalada K. Rao

Mechanical & Materials Engineering Faculty Publications

The goal of this work is to predict the effect of part geometry and process parameters on the direction and magnitude of heat flow heat flux in parts made using metal additive manufacturing (AM) processes. As a step towards this goal, the objective of this paper is to develop and apply the mathematical concept of heat diffusion over graphs to approximate the heat flux in metal AM parts as a function of their geometry. This objective is consequential to overcome the poor process consistency and part quality in AM. Currently, part build failure rates in metal AM often exceed 20 ...


The Role Of Low-Level Image Features In The Affective Categorization Of Rapidly Presented Scenes, L. Jack Rhodes, Matthew Rios, Jacob M. Williams, Gonzalo Quinones, Prahalada K. Rao, Vladimir Miskovic Jan 2019

The Role Of Low-Level Image Features In The Affective Categorization Of Rapidly Presented Scenes, L. Jack Rhodes, Matthew Rios, Jacob M. Williams, Gonzalo Quinones, Prahalada K. Rao, Vladimir Miskovic

Mechanical & Materials Engineering Faculty Publications

It remains unclear how the visual system is able to extract affective content from complex scenes even with extremely brief (< 100 millisecond) exposures. One possibility, suggested by findings in machine vision, is that low-level features such as unlocalized, two-dimensional (2-D) Fourier spectra can be diagnostic of scene content. To determine whether Fourier image amplitude carries any information about the affective quality of scenes, we first validated the existence of image category differences through a support vector machine (SVM) model that was able to discriminate our intact aversive and neutral images with ~ 70% accuracy using amplitude-only features as inputs. This model allowed us to confirm that scenes belonging to different affective categories could be mathematically distinguished on the basis of amplitude spectra alone. The next question is whether these same features are also exploited by the human visual system. Subsequently, we tested observers’ rapid classification of affective and neutral naturalistic scenes, presented briefly (~33.3 ms) and backward masked with synthetic textures. We tested categorization accuracy across three distinct experimental conditions, using: (i) original images, (ii) images having their amplitude spectra swapped within a single affective image category (e.g., an aversive image whose amplitude spectrum has been swapped with another aversive image) or (iii) images having their amplitude spectra swapped between affective categories (e.g., an aversive image containing the amplitude spectrum of a neutral image). Despite its discriminative potential, the human visual system does not seem to use Fourier amplitude differences as the chief strategy for affectively categorizing scenes at a glance. The contribution of image amplitude to affective categorization is largely dependent on interactions with the phase spectrum, although it is impossible to completely rule out a residual role for unlocalized 2-D amplitude measures.


Monolithic Heat-Transfer Device, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke Jan 2019

Monolithic Heat-Transfer Device, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke

Mechanical & Materials Engineering Faculty Publications

A monolithic heat-transfer device can include a container wall configured to retain a working fluid, where the container wall is formed of a single material. The container wall also includes an interior surface configured to be in fluid communication with the working fluid. The monolithic heat-transfer device also includes a channel disposed in the interior surface of the container wall, where the channel comprises a microstructure and a nanostructure. The microstructure and the nanostructure are materially contiguous with the single material forming the container wall. In some embodiments, the nanostructure comprises one or more layers of nanoparticles. The monolithic heat-transfer ...


Interface Facilitated Reorientation Of Mg Nanolayers In Mg-Nb Nanolaminates, Y. Chen, Mingyu Gong, N. A. Mara, Jian Wang Jan 2019

Interface Facilitated Reorientation Of Mg Nanolayers In Mg-Nb Nanolaminates, Y. Chen, Mingyu Gong, N. A. Mara, Jian Wang

Mechanical & Materials Engineering Faculty Publications

Mg/Nb nanolaminates synthesized through vapor deposition techniques exhibit high flow strength without conventional twinning in Mg. In this work, we investigated the influence of laminated microstructures on deformation mechanisms of Mg nanolayers. Using molecular dynamics simulations, we explored that (0001)-oriented Mg layers transform or re-orient to {10¯10}-oriented Mg layers through nucleation and growth of {10¯12} twins by atomic shuffling, instead of conventional {10¯12} twinning shear. Such a reorientation accommodates in-plane compressive strain and out-of-plane tensile strain when Mg/Nb laminates are subjected to compression parallel to the Mg/Nb interfaces. The nucleation of {10 ...