Digital Commons Network^™

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

Fast-, Light-Cured Scintillating Plastic For 3d-Printing Applications, Brian G. Frandsen, Michael Febbraro, Thomas Ruland, Theodore W. Stephens, Paul A. Hausladen, Juan J. Manfredi, James E. Bevins

Faculty Publications

Additive manufacturing techniques enable a wide range of possibilities for novel radiation detectors spanning simple to highly complex geometries, multi-material composites, and metamaterials that are either impossible or cost prohibitive to produce using conventional methods. The present work identifies a set of promising formulations of photocurable scintillator resins capable of neutron-gamma pulse shape discrimination (PSD) to support the additive manufacturing of fast neutron detectors. The development of these resins utilizes a step-by-step, trial-and-error approach to identify different monomer and cross-linker combinations that meet the requirements for 3D printing followed by a 2-level factorial parameter study to optimize the radiation detection …

Influence Of Nano-Sized Sic On The Laser Powder Bed Fusion Of Molybdenum, Nathan E. Ellsworth, Ryan A. Kemnitz, Cayla C. Eckley, Brianna M. Sexton, Cynthia T. Bowers, Joshua R. Machacek, Larry W. Burggraf

Faculty Publications

Consolidation of pure molybdenum through laser powder bed fusion and other additive manufacturing techniques is complicated by a high melting temperature, thermal conductivity and ductile-to-brittle transition temperature. Nano-sized SiC particles (0.1 wt%) were homogeneously mixed with molybdenum powder and the printing characteristics, chemical composition, microstructure, mechanical properties were compared to pure molybdenum for scan speeds of 100, 200, 400, and 800 mm/s. The addition of SiC improved the optically determined density and flexural strength at 400 mm/s by 92% and 80%, respectively. The oxygen content was reduced by an average of 52% over the four scan speeds analyzed. Two mechanisms …

A Comparison Of Layer Deposition And Open Molding Of Petg By Fused Pellet Fabrication In An Additive Manufacturing System, Alex Gibson, Jason Weaver

Faculty Publications

Additive manufacturing continues to offer new possibilities in both production and economics. The industry has quickly adopted it to rapidly produce parts that would be difficult or cost preventative otherwise. Recent innovation has expanded its capabilities, however there are still significant limitations. Most AM processes are restricted by materials available, in producing large parts, or by not achieving material deposition speeds to make certain products feasible. In addition, tight tolerances for features and surfaces cannot be produced without substantial post processing. High-speed Fused Pellet Fabrication (FPF) in combination with Hybrid Manufacturing (HM) offers expanded capabilities as additive and subtractive process …

Optimizing Build Plate Adhesion Of Polymers In Fused Granule Fabrication Processes, Alex Schroeder, Jason Weaver

Faculty Publications

Perhaps the most crucial element of fused granule fabrication (FGF) is material adhesion; in order to achieve a successful product, the material being printed must adhere to the build plate. For optimal products, the material should only adhere to the build plate until the print is complete, then be easily removable. This paper examines the effects of different build plates, environments, and bonding agents on material adhesion during the FGF process in a CNC mill machine. The force to remove polycarbonate (PC) and polypropylene (PP) from build plates was tested with various bonding agents. Except in one case, the adhesive …

Computational Based Investigation Of Lattice Cell Optimization Under Uniaxial Compression Load, Derek G. Spear, Jeremiah S. Lane, Anthony N. Palazotto, Ryan A. Kemnitz

Faculty Publications

Structural optimization is a methodology used to generate novel structures within a design space by finding a maximum or minimum point within a set of constraints. Topology optimization, as a subset of structural optimization, is often used as a means for light-weighting a structure while maintaining mechanical performance. This article presents the mathematical basis for topology optimization, focused primarily on the Bi-directional Evolutionary Structural Optimization (BESO) and Solid Isotropic Material with Penalization (SIMP) methodologies, then applying the SIMP methodology to a case study of additively manufactured lattice cells. Three lattice designs were used: the Diamond, I-WP, and Primitive cells. These …

Closed Loop Recycling Of Low Friction Polymers In Fused Granule Fabrication Additive Manufacturing Processes, Neil Thompson, Jason Weaver

Faculty Publications

Plastic waste is a critical worldwide problem that impacts additive manufacturing (AM). Extensive research has explored how plastic waste in AM can be reduced by recycling prints into new filament, with varying success. An alternative to filament-based extrusion is “fused granule fabrication” (FGF), which extrudes from pellets or granules. This method is often used for large area additive manufacturing (LAAM) of polymers. This paper expands upon the knowledge base from previous research on LAAM and examines the extent to which PETG can be recycled and reprinted through the same FGF tool without significant loss to its material properties. The metric …

Additive Manufacturing And Characterization Of Agi And Agi–Al2O3 Composite Electrolytes For Resistive Switching Devices, Benjamin J. Brownlee, Lok-Kun Tsui, Karthik Vempati, John B. Plumley, Brian D. Iverson, Thomas L. Peng, Fernando H. Garzon

Faculty Publications

This work investigates the electrochemical dynamics and performance of additively manufactured composite electrolytes for resistive switching. Devices are comprised of a Ag/AgI–Al₂O₃/Pt stack, where the solid state electrolyte is additively manufactured using extrusion techniques. AgI–Al₂O₃ composite electrolytes are characterized by x-ray diffraction and electrochemical impedance spectroscopy. The ionic conductivities of the electrolytes were measured for different concentrations of Al₂O₃, observing a maximum conductivity of 4.5 times the conductivity of pure AgI for composites with 20 mol. % Al₂O₃. There was little change in activation energy …

Impact Of Part Thickness And Drying Conditions On Saturation Limits In Binder Jet Additive Manufacturing, Nathan B. Crane

Faculty Publications

Binder jetting (BJ) is a high build-rate additive manufacturing process with growing commercial interest. Growth in BJ applications is driven by the use of finer powders and improved post-processing methods that can produce dense, homogenous final parts. However, understanding of the basic droplet/powder interaction is relatively limited. This paper considers the impact of in-process drying, part geometry, and droplet size on a key printing parameter: binder saturation. Parts of varying thicknesses are printed with a range of saturation levels under various heating conditions. The ratio of the printed part mass to the theoretical part mass is used to detect bleeding. …

Influence Of Droplet Velocity, Spacing, And Inter-Arrival Time On Line Formation And Saturation In Binder Jet Additive Manufacturing, Trenton Colton, Nathan B. Crane

Faculty Publications

Binder Jetting (BJ) is a low-cost Additive Manufacturing (AM) process that uses inkjet technology to selectively bind particles in a powder bed. BJ relies on the ability to control, not only the placement of binder on the surface but also its imbibition into the powder bed. This is a complex process in which picoliter-sized droplets impact powder beds at velocities of 1-10 m/s. However, the effects of printing parameters such as droplet velocity, size, spacing, and inter-arrival time on saturation level (fraction of pore space filled with binder) and line formation (merging of droplets to form a line) are unknown. …

Adhesion Testing Of Printed Inks While Varying The Surface Treatment Of Polymer Substrates, Clayton Neff, Edwin Elston, Amanda Schrand, Nathan B. Crane

Faculty Publications

Additive manufacturing with conductive materials enables new approaches to printed electronics that are unachievable by standard electronics manufacturing processes. In particular, electronics can be embedded directly into structural components in nearly arbitrary 3D space. While these methods incorporate many of the same materials, the new processing methods require standard test methods to compare materials, processing conditions, and determine design limits. This work demonstrates a test method to quantitatively measure the adhesion failure of printed inks deposited on a substrate without changing the ink printing conditions. The proposed method is an adaption of single lap shear testing in which the lap …

Mechanical And Temperature Resilience Of Multi-Material Systems For Printed Electronics Packaging, Clayton Neff, Justin Nussbaum, Chris Gardiner, Nathan B. Crane, James L. Zunino, Mike Newton

Faculty Publications

In this work, two AM technologies were utilized to compare the effectiveness of fabricating a simple electronic device with a conductive trace and hollow cylinder representative of ‘printed packaging’ that would survive harsh environmental conditions. The printed packaging cylinder delineates printed potting for electronics packaging. An nScrypt direct write (DW) system was the primary manufacturing system but a developing technology—coined large area projection sintering (LAPS)—manufactured a subset of samples for comparison. The tests follow Military Standard (MIL STD) 883K and include resiliency evaluation for die shear strength, temperature cycling, thermal shock, and high G loading by mechanical shock. Results indicate …

Impact Of Extended Sintering Times On Mechanical Properties In Pa-12 Parts Produced By Powderbed Fusion Processes, Garrett Craft, Justin Nussbaum, Nathan B. Crane, J. P. Harmon

Faculty Publications

Additive Manufacturing provides many advantages in reduced lead times and increased geometric freedom compared to traditional manufacturing methods, but material properties are often reduced. This paper considers powder bed fusion of polyamide 12 (PA12, Nylon 12) produced by three different processes: laser sintering (LS), multijet fusion (MJF)/high speed sintering (HSS), and large area projection sintering (LAPS). While all utilize similar PA12 materials, they are found to differ significantly in mechanical properties especially in elongation to break. The slower heating methods (MJF/HSS and LAPS) produce large elongation at break with the LAPS process showing 10x elongation and MJF/HSS exhibiting 2.5x the …

Experimental And Theoretical Investigation Of Mechanical Response Of Laser-Sintered Diamond Lattice Structures, Clayton Neff, Neil Hopkinson, Nathan B. Crane

Faculty Publications

Typically additive manufacturing (AM) processes are limited to a single material per part while many products benefit from the integration of multiple materials with varied properties. To achieve the benefits of multiple materials, the geometric freedom of AM could be used to build internal structures that emulate a range of different material properties such as stiffness, Poisson’s ratio, and elastic limit using only one build material. This paper examines the range of properties that can be simulated using diamond lattice structures manufactured from Nylon 12 with a commercial laser sintering process. Diamond lattices were fabricated with a unit cell length …

Impact Of Vapor Polishing On Surface Quality And Mechanical Properties Of Extruded Abs, Clayton Neff, Matthew Trapuzzano, Nathan B. Crane

Faculty Publications

Purpose — Additive manufacturing (AM) is readily capable of producing models and prototypes of complex geometry and is advancing in creating functional parts. However, AM processes typically underperform traditional manufacturing methods in mechanical properties, surface roughness, and hermeticity. Solvent vapor treatments (vapor polishing) are commonly used to improve surface quality in thermoplastic parts, but the results are poorly characterized.

Design/methodology/approach — This work quantifies the surface roughness change and also evaluates the effect on hermeticity and mechanical property impacts for “as-printed” and acetone vapor-polished ABS tensile specimens of 1, 2, and 4 mm thicknesses produced by material extrusion (FDM).

Findings …

Stress-Limiting Test Structures For Rapid Low-Cost Strength And Stiffness Assessment, Andrew Katz, Craig P. Lusk, Nathan B. Crane

Faculty Publications

Purpose: Evaluate the use of a simple printed geometry to estimate mechanical properties (elastic modulus, yield strength) with inexpensive test equipment.

Design Methodology/Approach: Test geometry is presented that enables controlled strains with manual deformation and repeatable measurement of vibrational frequencies. This is tested with multiple FDM machines to assess measurement accuracy and repeatability. Printing orientation and some printing parameters are varied to assess the measurement sensitivity.

Findings: The test methods show good correlation with manufacturer material specifications in the X-Y plane and reported elastic strain limits. It is also sensitive to printing orientation and printing parameters.

Research Limitations/Implications: Further work …