Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 10 of 10
Full-Text Articles in Entire DC Network
An Updated Overview Of Diamond-Like Carbon Coating In Tribology
An Updated Overview Of Diamond-Like Carbon Coating In Tribology
Faculty of Engineering University of Malaya
During the last two decades, the industry (including scientists) has focused on diamond-like carbon (DLC) coating because of its wide range of application in various fields. This material has numerous applications in mechanical, electrical, tribological, biomedical, and optical fields. Severe friction and wear in some machine parts consumes high amount of energy, which makes the process energy inefficient. Thus, DLC coating can be an effective means to lower the friction and wear rate. Some important process variables that affect the tribological characteristics of DLC coating are adhesion promoter intermediate layer, substrate surface roughness, hydrogen incorporation or hydrogen non involvement, and …
Structural And Mechanical Properties Of Nanostructured Tio2 Thin Films Deposited By Rf Sputtering
Structural And Mechanical Properties Of Nanostructured Tio2 Thin Films Deposited By Rf Sputtering
A.S. Md Abdul Haseeb
This study mainly aims to evaluate the effects of substrate temperatures on the mechanical properties of TiO2 thin films deposited on glass substrates by radio-frequency (RF) magnetron sputtering. All titania films possess anatase structure having a nodular morphology. AES results reveal that Si and Na ions from glass diffuse into TiO2 films at higher substrate temperatures. Micro-scratch and wear tests were conducted to evaluate their mechanical and tribological properties. The adhesion critical loads of TiO2 films deposited at room temperature, 200 and 300°C are found to be 1.51, 1.54 and 1.08N, respectively. Scratch hardness also increases from 11.5 to 13.6GPa …
Effect Of Temperature On Tribological Properties Of Palm Biodiesel
Effect Of Temperature On Tribological Properties Of Palm Biodiesel
A.S. Md Abdul Haseeb
Biodiesel, as an alternative fuel is steadily gaining attention to replace petroleum diesel partially or completely. The tribological performance of biodiesel is crucial for its application in automobiles. In the present study, effect of temperature on the tribological performance of palm biodiesel was investigated by using four ball wear machine. Tests were conducted at temperatures 30, 45, 60 and 75 °C, under a normal load of 40 kg for 1 h at speed 1200 rpm. For each temperature, the tribological properties of petroleum diesel (B0) and three biodiesel blends like B10, B20, B50 were investigated and compared. During the wear …
Tribo-Surface Characteristics Of Al-B4c And Al-Sic Composites Worn Under Different Contact Pressures
Tribo-Surface Characteristics Of Al-B4c And Al-Sic Composites Worn Under Different Contact Pressures
A.S. Md Abdul Haseeb
Tribo-surface characteristics of two aluminium metal matrix composites (Al-MMC) of compositions Al-13 vol%B4C and Al-13 vol%SiC sliding against a commercial phenolic brake pad have been investigated under dry conditions. The wear tests were carried out using a pin-on-disc type apparatus at a linear speed of 1.62 m s-1 under contact pressures ranging from 0.75 to 3.00 MPa. The coefficient of friction was recorded on line. Wear rates were calculated from mass loss measurements. Scanning electron microscope equipped with energy dispersive X-ray spectroscopy was used to examine the tribo-surface. It is found that wear rate of both composites increases with increasing …
Chemical And Structural Nature Of Tribo-Surface Of Aluminium-Sic Composites At Nanometre And Micrometre Length Scales
A.S. Md Abdul Haseeb
The worn surface of Al-SiC metal matrix composites (MMC) sliding against phenolic brake pad at a linear sliding speed of 1.62 m s-1 under contact pressures of 0.75-3.00 MPa in a pin-on-disc apparatus was investigated. XPS was used to extract information from the top few nanometres of the worn surface, while scanning electron microscopy and energy dispersive X-ray microanalysis (SEM-EDX) provided information from within a few micrometres. Results reveal that the surface of Al-SiC undergoes significant chemical and physical changes during wear. The tribo-surface on Al-SiC is converted into a mixture that contains the constituents of Al-SiC and the phenolic …
Velocity Effects On The Wear, Friction And Tribochemistry Of Aluminum Mmc Sliding Against Phenolic Brake Pad
A.S. Md Abdul Haseeb
Two aluminum metal matrix composites (MMC) reinforced with 13 vol.% of SiC or B4C particles were made by stir casting followed by hot extrusion. Effects of sliding velocity on the wear, friction and tribochemistry of the worn surfaces of both composites sliding against a commercial phenolic brake pad have been investigated under dry condition. The wear tests were carried out using a pin-on-disc type apparatus at two linear sliding speeds: 1.62 and 4.17 m s-1 under a constant contact pressure of 0.75 MPa for a sliding distance of 5832 m. The coefficient of friction was recorded and wear rate of …
Velocity Effects On The Wear, Friction And Tribochemistry Of Aluminum Mmc Sliding Against Phenolic Brake Pad
A.S. Md Abdul Haseeb
Two aluminum metal matrix composites (MMC) reinforced with 13 vol.% of SiC or B4C particles were made by stir casting followed by hot extrusion. Effects of sliding velocity on the wear, friction and tribochemistry of the worn surfaces of both composites sliding against a commercial phenolic brake pad have been investigated under dry condition. The wear tests were carried out using a pin-on-disc type apparatus at two linear sliding speeds: 1.62 and 4.17 m s-1 under a constant contact pressure of 0.75 MPa for a sliding distance of 5832 m. The coefficient of friction was recorded and wear rate of …
Response Of Ti-6al-4v And Ti-24al-11nb Alloys To Dry Sliding Wear Against Hardened Steel
Response Of Ti-6al-4v And Ti-24al-11nb Alloys To Dry Sliding Wear Against Hardened Steel
A.S. Md Abdul Haseeb
Titanium alloys have been of great interest in recent years because of their very attractive combination of high strength, low density and corrosion resistance. Application of these alloys in areas where wear resistance is also of importance calls for thorough investigations of their tribological properties. In this work, Ti-6Al-4V and Ti-24Al-11Nb alloys were subjected to dry sliding wear against hardened-steel counter bodies and their tribological response was investigated. A pin-on-disc type apparatus was used with a normal load of 15-45N and sliding speed of 1.88 ms -1. In the steady state, it was demonstrated that Ti-24Al-11Nb had a substantially higher …
Tribological Behaviour Of Quenched And Tempered, And Austempered Ductile Iron At The Same Hardness Level
A.S. Md Abdul Haseeb
The tribological behaviour of ductile iron heat-treated by two different procedures viz. quenching and tempering, and austempering to an identical matrix hardness of 445 KHN is compared. Wear tests were carried out using a pin-on-disc type apparatus under dry sliding conditions at a linear speed of 1.18 m s -1. Applied load and sliding distance in the range of 7.5-30 N and 2x10 4-6x10 4 m, respectively, were used. It was observed that under all test conditions, austempered ductile iron exhibits a better wear resistance than quenched and tempered ductile iron, although both have an identical chemical composition and matrix …
Effect Of Mechanical Factors On Tribological Properties Of Palm Oil Methyl Ester Blended Lubricant
Effect Of Mechanical Factors On Tribological Properties Of Palm Oil Methyl Ester Blended Lubricant
A.S. Md Abdul Haseeb
The effects of mechanical factors viz. applied load and temperature on the tribological performance of 5% palm oil methyl ester (POME) blended lubricant were studied using a steel-cast iron pair. Wear and frictional measurements were made using a stationary steel ball and a reciprocating cast iron plate in a modified universal wear and friction testing machine. The test conditions were contact pressure, 400 MPa; mean contact velocity, 0.34 m/s; reciprocating stroke, 80 mm; loads, 100-1100 N (fixed temperature); and temperature, 40-140°C (fixed load). Wear scar surfaces were investigated using scanning electron microscopy (SEM) to understand the wear mechanisms involved. Analysis …