Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 6 of 6
Full-Text Articles in Entire DC Network
Mechanical Properties Of Intermetallic Compounds In Electrodeposited Multilayered Thin Film At Small Scale By Nanoindentation
Faculty of Engineering University of Malaya
Mechanical properties of intermetallic compounds (IMCs) which were formed in electrodeposited Cu/Sn and Cu/Ni/Sn multilayered thin film have been investigated. The layers of Cu, Sn and Ni were formed by electrodeposition technique using copper pyrophosphate, tin methanesulfonic and nickel Watts baths, respectively. After synthesis, samples were subjected to high temperature aging at 150 degrees C for 168 h. Two different types of intermetallics Cu3Sn and Cu6Sn5 were formed in Cu/Sn. After adding ultra-thin layer of Ni (70 nm) in between Cu and Sn layers, (Cu, Ni)(6)Sn-5 was formed after aging at similar condition to that of Cu/Sn. Tin whisker growth …
Evaluating The Optical Properties Of Tio2 Nanofluid For A Direct Absorption Solar Collector
Evaluating The Optical Properties Of Tio2 Nanofluid For A Direct Absorption Solar Collector
Faculty of Engineering University of Malaya
Recent studies specify that designated nanofluids may increase the proficiency of direct absorption solar thermal collectors. To determine the efficiency of nanofluids in solar applications, their capability to change light energy to thermal energy must be identified (i.e., the absorption spectrum of the solar material). In view of that, this study compares model predictions to spectroscopic measurements of extinction coefficients over wavelengths that are important for solar energy (200- 1100nm). In the first decade of nanofluid research, most of the focus was on measuring and modeling the fundamental thermophysical properties of nanofluids (i.e., thermal conductivity, density, viscosity, and convection coefficients). …
The Tribological And Electrochemical Behavior Of Hvof-Sprayed Cr3c2-Nicr Ceramic Coating On Carbon Steel
Faculty of Engineering University of Malaya
High Velocity Oxygen Fuel (HVOF) is an excellent approach to prepare a good, wear-resistant lamella of Chromium Carbide-Nickel Chrome (Cr3C2-NiCr) on carbon steel for high temperature application. This research investigates the effect of a thin, deposited layer of Cr3C2-NiCr on carbon steel in terms of wear and corrosion properties. The microstructure of the HVOF-sprayed Cr3C2-NiCr coating was characterized at each step by scanning electron microscopy. Wear testing was performed with a pin-on-disk tester. Wear weight loss was examined by applying different loads over a 9048.96 m sliding distance. Experimental results show that the wear resistance of the coated sample reduced …
Sintering Behaviour Of Natural Porous Hydroxyapatite Derived From Bovine Bone
Sintering Behaviour Of Natural Porous Hydroxyapatite Derived From Bovine Bone
Faculty of Engineering University of Malaya
The aim of this research is to study the properties of natural porous hydroxyapatite developed from bovine bone through a sintering process. Bovine bone samples were prepared and sintered in an air atmosphere at different temperatures ranging from 600 degrees C to 1000 degrees C. The sintered bodies were characterized to determine the phases present, bulk density, Ca/P ratio and Vickers hardness. In addition, the microstructural evolution of the sintered porous bodies was also examined. The results revealed that the thermal stability of the HA matrix was not disrupted and that all of the sintered bodies exhibited phase pure HA. …
Sintering Behaviour Of Natural Porous Hydroxyapatite Derived From Bovine Bone
Sintering Behaviour Of Natural Porous Hydroxyapatite Derived From Bovine Bone
Faculty of Engineering University of Malaya
The aim of this research is to study the properties of natural porous hydroxyapatite developed from bovine bone through a sintering process. Bovine bone samples were prepared and sintered in an air atmosphere at different temperatures ranging from 600 degrees C to 1000 degrees C. The sintered bodies were characterized to determine the phases present, bulk density, Ca/P ratio and Vickers hardness. In addition, the microstructural evolution of the sintered porous bodies was also examined. The results revealed that the thermal stability of the HA matrix was not disrupted and that all of the sintered bodies exhibited phase pure HA. …
Review Of Improvements In Wire Electrode Properties For Longer Working Time And Utilization In Wire Edm Machining
Faculty of Engineering University of Malaya
Wire electrical discharge machining (WEDM) is an important technology, which demands high-speed cutting and high-precision machining to realize productivity and improved accuracy for manufacturing hard materials. WEDM has experienced explosive growth and complexity of equipment as well as rising demand for the basic process tool (the wire electrode). Greater taper angles, thicker workpieces, automatic wire threading, and long periods of unattended operation make the selection of the ideal wire a much more critical basis for achieving successful operation. This paper focuses on the evolution of EDM wire electrode technologies from using copper to the widely employed brass wire electrodes and …