Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 13 of 13
Full-Text Articles in Entire DC Network
Experimentally Study The Effects Of Fins Height And Width H\W Ratio To The Fin Thermal Performance By Natural Convections, Hazim A.M. Al-Jewaree, Osama A.M. Alhamil
Experimentally Study The Effects Of Fins Height And Width H\W Ratio To The Fin Thermal Performance By Natural Convections, Hazim A.M. Al-Jewaree, Osama A.M. Alhamil
Innovative Research Publications IRP India
The industry revolution in thermal engineering started with fixed the extended surface area named a fin. Therefore, a lot off research work done in this field to enhance the performance of heat transfer . All, previous work reach to that any increase of heat transfer coefficient and the fin surface area will increase the heat transfer rate by natural convection. The research work summarized in this paper presents an experimental investigation on the effect of fin heights –width (H/w) ratios on the fin performance using rectangular plate type fins. The steady-state natural convection heat transfer from vertical rectangular fins extending …
Review On The Suitability Of Conceptual Performance Measurement Systems For Lean Manufacturing, Dilanthi M. G.S
Review On The Suitability Of Conceptual Performance Measurement Systems For Lean Manufacturing, Dilanthi M. G.S
Innovative Research Publications IRP India
Lean manufacturing is implemented to improve any organizational performance so that its performance should be measured to assure the organizational goal attainment. But the past studies have not yet suggested any specific performance measurement system for lean manufacturing. Therefore this paper reviews the conceptual performance measurement systems and their suitability to measure the lean performance and hence argues that a new performance measurement framework should be developed.
Strengthening Of Rc Beam And Column Joint By Using Cfrp & Gfrp, M .A Nawale, A. J. , Mehetre, . S. B. Kandekar
Strengthening Of Rc Beam And Column Joint By Using Cfrp & Gfrp, M .A Nawale, A. J. , Mehetre, . S. B. Kandekar
Innovative Research Publications IRP India
This paper will give the information about strengthening of different parameter by using CFRP & GFRP. Strengthening of existing structures has become a major part of construction activity in our country. Many civil structures are no longer safe due to increased load specifications in the design codes. The beam column joint is the crucial zone in a reinforced concrete moment resisting frame. It is subjected to large forces during severe ground shaking and its behaviour has a significant influence on the response of the structure. The assumption of joint being rigid fails to consider the effects of high shear forces …
Responses Of Ka’Oje Metallurgical Manganese Ore To Gravity Concentration Techniques, R. A. Muriana
Responses Of Ka’Oje Metallurgical Manganese Ore To Gravity Concentration Techniques, R. A. Muriana
Innovative Research Publications IRP India
Metallurgical manganese ore samples from Ka’oje (Nigeria) were enriched to higher Metallurgical grades during wet gravity separation techniques which included Jigging and Tabling operations. As-mined samples S1 (36.83%MnO), S2 (47.85%MnO), S3 (58.85%MnO) and S4 (54.96%MnO) were dressed and screened to -780+500 μm, -500+355μm, -355+250 μm, -250+192 μm and -192 μm particle size ranges. Obtained Jigging test concentrates assayed 51.54% MnO minimum recovery level with an enrichment ratio (ER) of 1.02; while Tabling operation concentrates assayed 91.11% MnO maximum recovery and 1.14 ER value. These responses demonstrated the suitability of the two techniques in raising the enrichment levels of the ores …
Design & Analysis Of Ø40” X 80” Conventional Sugar Mill Head Stock., Santosh Y. Salunkhe
Design & Analysis Of Ø40” X 80” Conventional Sugar Mill Head Stock., Santosh Y. Salunkhe
Innovative Research Publications IRP India
Sugar mill head stock play a significant role in the sugar plant as they have to sustain the forces experienced by the rollers while extracting juice from the cane. The present analysis related to modification in sugar mill head stock Ø40”X80”. This paper describes the advantages of using Ø40”X80” mill head stocks by designing & analysis by ANSYS software. In this study theoretical study has been done considering the Bending moment & force polygon diagrams. Bending moment factor which helps in finding actual results. By changing various parameters the performance of mill head stocks is studies using static structural analysis …
Sample Size Effect On Combustion Analysis, Osueke C. O, Uguru Okorie Daniel, Aondoyila Kuhe
Sample Size Effect On Combustion Analysis, Osueke C. O, Uguru Okorie Daniel, Aondoyila Kuhe
Innovative Research Publications IRP India
Engine parameters vary from one cycle to the other and this makes engine analysis with data from a single working cycle insufficient in capturing or modelling an engine behaviour. The variation observed in engine has necessitated the use sample sizes of data obtained during an engine operation to obtain results that are representative of the engine being investigated. Research has shown that the use of very large data sample size increases the storage needed and processing time and does not necessary give better results over results obtained with lesser sample sizes. The number of sample size to use for analysis …
Enhancement Of Performance Parameters Of Transformer Using Nanofluids, Innovative Research Publications Irp India, Raja Sekhar Dondapati, Vishnu Saini, Niraj Kishore, Vicky V
Enhancement Of Performance Parameters Of Transformer Using Nanofluids, Innovative Research Publications Irp India, Raja Sekhar Dondapati, Vishnu Saini, Niraj Kishore, Vicky V
Innovative Research Publications IRP India
Transformer is a soul of both transmission and distribution systems. It performs low voltage to high voltage conversion in transmission lines and similarly high voltage to low voltage conversion in distribution lines. The operation of transformer is decided by the cooling provided to the system. The efficient cooling method is achieved by the use of forced (or) natural oil cooling medium. The oils used for the purpose of coolants are the hydrocarbons of paraffin (or) naphtha based petroleum products. The oil is used as coolant is made from highly refined mineral oil and it has high dielectric strength. During the …
Permeability Test Measurement Of Composite Material For Reusable Launching Vehicles (Rlv), Innovative Research Publications Irp India, Charanjit Singh, Karthik Sunil, Prudhvinath Reddy, Idris Syed Mahaboob, Dondapati, Raja Sekhar
Permeability Test Measurement Of Composite Material For Reusable Launching Vehicles (Rlv), Innovative Research Publications Irp India, Charanjit Singh, Karthik Sunil, Prudhvinath Reddy, Idris Syed Mahaboob, Dondapati, Raja Sekhar
Innovative Research Publications IRP India
Polymer composites are replacing metals over the time due to their light weight, high strength to weight ratio, excellent physical and thermal properties. Hence, they are ideal candidates where weight is of particular concern. One such application is reusable launch vehicles (RLV). Use of polymer Composite materials instead of conventional metal alloys for fuel tank reduces weight of launching vehicle so that more payloads can be carried into space, thereby reducing cost per kilogram of payload. Polymer composites at room temperature show familiar properties but when they are exposed to low temperature, properties change rapidly and show abnormal behavior. Material …
Development Of Composite Material Testing Facility For Cryogenic Fuel Tank Applications, Innovative Research Publications Irp India, Sandeep Singh, Karthik Sunil, Prudhvinath Reddy, Idris Syed Mahaboob, Raja Sekhar Dondapati
Development Of Composite Material Testing Facility For Cryogenic Fuel Tank Applications, Innovative Research Publications Irp India, Sandeep Singh, Karthik Sunil, Prudhvinath Reddy, Idris Syed Mahaboob, Raja Sekhar Dondapati
Innovative Research Publications IRP India
Composite materials are being used extensively in different realms of science for various applications. There use is prominent in the aerospace industry. The testing of these composite materials is of substantial importance, as they might be susceptible to failure due to the variation in the temperature ranges and the cryogenic temperatures which the materials have to endure. In the present work, the tensile strength of composite materials are observed using double walled vacuum chamber which is designed for the Universal Testing Machine (UTM)
Design And Analysis Of Leaf Spring - Using Fea Approach, Innovative Research Publications Irp India, Hareesh K, Thillikkani S
Design And Analysis Of Leaf Spring - Using Fea Approach, Innovative Research Publications Irp India, Hareesh K, Thillikkani S
Innovative Research Publications IRP India
The aim of this paper is to represent a general study the design and analysis of leaf spring. The suspension system in a vehicle significantly affects the behavior of vehicle. Leaf springs are subjected to millions of varying stress cycles loading to fatigue failure. Leaf springs are special kind of springs used in automobile suspension systems. The main function of leaf spring is not only to support vertical load but also to isolate road induced vibrations. The present work attempts to linear Static analysis determines the safe stress and corresponding pay load of the leaf spring and analyze the safe …
Research On Optimization Of Plunge Centerless Grinding Process Using Genetic Algorithm And Response Surface Method, Innovative Research Publications Irp India, Phan Bui Khoi, Do Duc Trung, Ngo Cuong, Nguyen Dinh Man
Research On Optimization Of Plunge Centerless Grinding Process Using Genetic Algorithm And Response Surface Method, Innovative Research Publications Irp India, Phan Bui Khoi, Do Duc Trung, Ngo Cuong, Nguyen Dinh Man
Innovative Research Publications IRP India
This paper presents the research on optimization of plunge centerless grinding process when grind 20X – carbon infiltration steel (ГOCT standard - Russia) to achieve minimum of roundness error value. The input parameters are center height angle of the workpiece ( ), longitudinal grinding wheel dressing feed-rate ( Ssd ), plunge feed-rate ( k S ) and control wheel velocity ( dd v ). Using the result of 29 runs in Central Composite Design matrix to given the second order roundness error model. Genetic algorithm and Response surface method were used to focus on determination of optimum centerless grinding …
Microstructure And Mechanical Properties Of Multipass Friction Stir Processed Aluminum Silicon Carbide Metal Matrix, Innovative Research Publications Irp India, V V Murali Krishna G, K.S Atyanarayana
Microstructure And Mechanical Properties Of Multipass Friction Stir Processed Aluminum Silicon Carbide Metal Matrix, Innovative Research Publications Irp India, V V Murali Krishna G, K.S Atyanarayana
Innovative Research Publications IRP India
In this study, SiC particles were incorporated by using Friction Stir Processing (FSP) into the 6351 aluminium alloy to form particulate composite materials. Sampels were subjected to constant rotational and traverse speeds of the FSP tool with and without SiC reinforcements. Microstructural observations were carried out by employing optical microscopy of the modifiedsurfaces. Mechanical properties were evaluated by tensile test on UTM. For the 100% overlapping, No.of passes caused grain modification in the processed zone. The tensile test results indicate an improvement of strength and Microhardness for Single Pass FSP samples and a reduction in the strength of FSP samples …
Fractographical Investigation Of The Delamination Under Fatigue Using Laser Confocal Electron Microscope, Innovative Research Publications Irp India, Rafiullah Khan,Sakhi Jan, Sajjad Ahmad,,Muhammad Amjadsaeed Badshah, Mutahir Ahmad
Fractographical Investigation Of The Delamination Under Fatigue Using Laser Confocal Electron Microscope, Innovative Research Publications Irp India, Rafiullah Khan,Sakhi Jan, Sajjad Ahmad,,Muhammad Amjadsaeed Badshah, Mutahir Ahmad
Innovative Research Publications IRP India
In this paper fracture surface of the fatigue delamination have been investigated. Fatigue delamination tests were performed on the crabon/epoxy under different stress ratios. Samples were cut from the DCB specimens and analyzed in Laser Confocal Scanning Microscope. The analysis was used to measure the roughness values. Different fractographic features observed in the study are discussed.