Digital Commons Network^™

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …

A Modular Framework For Surface-Embedded Actuation And Optical Sensing In Soft Robots., Paul Bupe Jr

Electronic Theses and Dissertations

This dissertation explores the development and integration of modular technologies in soft robotics, with a focus on the OptiGap sensor system. OptiGap serves as a simple, flexible, cost-effective solution for real-time sensing of bending and deformation, validated through simulation and experimentation. Working as part of an emerging category of soft robotics called Soft, Curved, Reconfigurable, Anisotropic Mechanisms, or SCRAMs, this research also introduces the Thermally-Activated SCRAM Limb (TASL) technology, which employs shape-memory alloy (SMA) wire embedded in curved sheets for surface actuation and served as the initial inspiration for OptiGap. In addition, the EneGate system is presented as a complementary …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …

Collaborative Human-Machine Interfaces For Mobile Manipulators., Shamsudeen Olawale Abubakar

Electronic Theses and Dissertations

The use of mobile manipulators in service industries as both agents in physical Human Robot Interaction (pHRI) and for social interactions has been on the increase in recent times due to necessities like compensating for workforce shortages and enabling safer and more efficient operations amongst other reasons. Collaborative robots, or co-bots, are robots that are developed for use with human interaction through direct contact or close proximity in a shared space with the human users. The work presented in this dissertation focuses on the design, implementation and analysis of components for the next-generation collaborative human machine interfaces (CHMI) needed for …

Additive Manufacturing Using Robotic Manipulators, Fdm, And Aerosol Jet Printers., Alexander Curry

Electronic Theses and Dissertations

Additive manufacturing has created countless new opportunities for fabrication of devices in the past few years. Advances in additive manufacturing continue to change the way that many devices are fabricated by simplifying processes and often lowering cost. Fused deposition modeling (FDM) is the most common form of 3D printing. It is a well-developed process that can print various plastic materials into three-dimensional structures. This technology is used in a lot of industries for rapid prototyping and sometimes small batch manufacturing. It is very inexpensive, and a prototype can be created in a few hours, rather than days. This is useful …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Challenges In Flexible Microsystem Manufacturing : Fabrication, Robotic Assembly, Control, And Packaging., Danming Wei

Electronic Theses and Dissertations

Microsystems have been investigated with renewed interest for the last three decades because of the emerging development of microelectromechanical system (MEMS) technology and the advancement of nanotechnology. The applications of microrobots and distributed sensors have the potential to revolutionize micro and nano manufacturing and have other important health applications for drug delivery and minimal invasive surgery. A class of microrobots studied in this thesis, such as the Solid Articulated Four Axis Microrobot (sAFAM) are driven by MEMS actuators, transmissions, and end-effectors realized by 3-Dimensional MEMS assembly. Another class of microrobots studied here, like those competing in the annual IEEE Mobile …

Grid-Connected Photovoltaic Systems Based On Nonlinear Control., Pablo R. Rivera

Electronic Theses and Dissertations

Nowadays, due to the high-scale penetration of photovoltaic systems, reliable and efficient grid-connected photovoltaic (PV) systems utilizing the advances of power electronics and control system technology are desirable. Thus, single-stage grid-connected photovoltaic systems, have gained attention, especially in low voltage applications. However, PV systems exhibit nonlinear behavior that could negatively affect the performance of the system if they are not adequately compensated for. In this dissertation, using the general structure for the synchronous dq0 frame, a single-stage three-phase grid-connected photovoltaic system, and a single-stage single-phase grid-connected PV system, both with a nonlinear control strategy, are developed to track the maximum …

Psychophysiological Analysis Of A Pedagogical Agent And Robotic Peer For Individuals With Autism Spectrum Disorders., Mohammad Nasser Saadatzi

Electronic Theses and Dissertations

Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by ongoing problems in social interaction and communication, and engagement in repetitive behaviors. According to Centers for Disease Control and Prevention, an estimated 1 in 68 children in the United States has ASD. Mounting evidence shows that many of these individuals display an interest in social interaction with computers and robots and, in general, feel comfortable spending time in such environments. It is known that the subtlety and unpredictability of people’s social behavior are intimidating and confusing for many individuals with ASD. Computerized learning environments and robots, however, prepare a predictable, …

Osem : Occupant-Specific Energy Monitoring., Anand S. Kulkarni

Electronic Theses and Dissertations

Electricity has become prevalent in modern day lives. Almost all the comforts people enjoy today, like home heating and cooling, indoor and outdoor lighting, computers, home and office appliances, depend on electricity. Moreover, the demand for electricity is increasing across the globe. The increasing demand for electricity and the increased awareness about carbon footprints have raised interest in the implementation of energy efficiency measures. A feasible remedy to conserve energy is to provide energy consumption feedback. This approach has suggested the possibility of considerable reduction in the energy consumption, which is in the range of 3.8% to 12%. Currently, research …