Digital Commons Network^™

Failure Of High Strength Concrete Under Dynamic Uniaxial Compression, Colin Loeffler

Mechanical Engineering Research Theses and Dissertations

The failure strength of concrete materials has been widely shown to be dependent on experimental parameters such as specimen geometry and strain-rate. The effects of specimen geometry have been shown both theoretically and experimentally to be a result of the quasi-brittle nature of concrete. While the failure strength of concrete has been widely reported to increase significantly when deformed at high strain-rates, the physical mechanisms driving this phenomenon remain the source of debate amongst researchers. This means that constitutive models designed to predict this rate dependent behavior are not based on the real physical mechanisms that drive this behavior but …

Graphene-Based Water Desalination Using Atomistic Simulations, Thanh Chinh Nguyen

Mechanical Engineering Research Theses and Dissertations

My research focused on investigating saltwater transport through nanoporous graphene membranes using molecular dynamics (MD) simulations. Particularly, in this dissertation, we focused on pressure-driven flows of salt water through uncharged and charged nanoporous graphene membranes for water desalination applications. In the first study, desalination performance of uncharged single-layer nanoporous graphene membranes was observed based on volumetric flow rate, required pressure drop, and salt rejection efficiency. A functional relationship between the volumetric flow rate, pressure drop, pore diameter, and the dynamic viscosity of saltwater was also examined. In further studies, transport of salt ions through positively and negatively charged single-layer nanoporous …

Development Of A Robotized Laser Directed Energy Deposition System And Process Challenges, Meysam Akbari

Mechanical Engineering Research Theses and Dissertations

Metal additive manufacturing (AM) is a disruptive technology, enabling fabrication of complex and near net shaped parts by adding material in a layer-wise fashion. It offers reduced lead production time, decreased buy-to-fly ratio, and repair and remanufacturing of high value components. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical and mold tooling. However, beside tremendous advantages of AM, there are still some challenges that prevent the adoption of this technology into high standard applications. Anisotropy and inhomogeneity in mechanical properties of the as-built parts and existence of pores and lack-of-fusion defects are considered as …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Undergraduate Researcher Awarded at Georgia Environmental Conference

Investigation Of The Electrode Polarization Effect For Biosensor Applications, Anil Koklu

Mechanical Engineering Research Theses and Dissertations

My research focuses on electrokinetic transport. Particularly, in this dissertation, we focus on fabrication and testing of micro electrodes with nanostructured surfaces to minimize the electrode polarization (EP) effects for biosensor applications. In the first study, electrochemical deposition of gold nanoparticles on to planar gold electrodes was used to generate rough surfaces. Dendritic nanostructures that reduced EP up to two orders of magnitude was obtained by optimizing the deposition conditions. These structures also enhanced dielectrophoresis (DEP) response of our bio-chips, making them usable in physiological buffers. In further studies we discovered a universal scaling of EP in the frequency domain, …

The Axisymmetric Harmonic Element Including Gyroscopic Effects: A Complete Derivation, Zachary Charles Glick

Graduate Theses - Mechanical Engineering

Various types of finite elements have been used in the prediction of critical speeds of turbomachinery. Among these, axisymmetric harmonic elements provide both accurate natural frequency prediction and computational speed. Yet, a full derivation of such an element including gyroscopic effects is not widely available in the relevant literature. In this work, the finite elements for rotordynamics available in the literature are reviewed. Derivations necessary for the axisymmetric harmonic element mass, gyroscopic damping, and stiffness matrices and the equations of motion are clearly expounded using Hamilton’s principle. The formulation is applied to two model shafts, and the comparison of results …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Graphs And Cad: Analyzing The Experience Of A Mechanical Engineering Intern, Matthew Des Biens

Celebration of Learning

A reflection on the experiences of a mechanical engineering intern at Bergstrom Inc., this presentation, by Senior Matt Des Biens, will discuss what it was like working for a manufacturing and design company making HVAC units for large customers across the world. The highlights will be on the projects he worked on, the things that he learned, and his views on working for the company as a whole.

Design Of An Urban Garden Aquaponics System, Riley Albright-Borden, James Wang, Sydney Thompson

Interdisciplinary Design Senior Theses

The project objective is to create a durable, off-the-grid, large-scale aquaponics system consisting of over 90 sq. ft of growing space, a 650-gallon fishpond, and four types of sensors to transmit water quality data to the internet for remote water quality monitoring. The end goal of the project is to supplement produce grown in the garden to further increase fresh, nutritional options available in meals cooked and distributed by Loaves and Fishes Family Kitchen to combat food insecurity in San Jose. This report presents the need for a system, details the various subsystems, and the rationale for the designs. It …

Design And Control Of Fiber Encapsulation Additive Manufacturing, Matt Saari

Mechanical Engineering Research Theses and Dissertations

This work presents the design, development, and analysis of the Fiber Encapsulation Additive Manufacturing (FEAM) system developed at the Laboratory for Additive Manufacturing Robotics \& Automation at the Lyle School of Engineering at Southern Methodist University. The innovation introduced by FEAM is the ability to insert a continuous fiber of different material into the flowing extrudate. Correctly positioning the fiber feed inside the extrudate while turning the fiber in arbitrary directions is a critical aspect of the technology. This will allow for the full exploitation of the capabilities of the FEAM technology to produce robotic components that actuate and sense. …

Fault Adaptive Workload Allocation For Complex Manufacturing Systems, Charlie B. Destefano

Graduate Theses and Dissertations

This research proposes novel fault adaptive workload allocation (FAWA) strategies for the health management of complex manufacturing systems. The primary goal of these strategies is to minimize maintenance costs and maximize production by strategically controlling when and where failures occur through condition-based workload allocation.

For complex systems that are capable of performing tasks a variety of different ways, such as an industrial robot arm that can move between locations using different joint angle configurations and path trajectories, each option, i.e. mission plan, will result in different degradation rates and life-expectancies. Consequently, this can make it difficult to predict when a …

The Effects Of Scale On Granular Mixing In A Double Screw Pyrolyzer, Breanna L. Marmur

Breanna L. Marmur

Granular mixing processes are important to many industries including the pharmaceutical, agricultural, and biotechnology industries. These processes often require both a high degree of homogeneity and a high degree of customizability. As granular mixing processes are so widely employed, a thorough understanding of the mixing dynamics is necessary to understand and control the resulting products. Research into granular mixing processes has been, thus far, largely focused on laboratory scale mixers with simple geometries, while actual industrial processes often require large mixers with complex geometries. Moreover, granular mixing processes are often very sensitive to changes in operating conditions and any solutions …

Hybrid Laser/Arc Welding Of Difficult-To-Weld Thick Steel Plates In Different Joint Configurations: Issues And Resolutions, Nima Yazdian

Mechanical Engineering Research Theses and Dissertations

Difficult-to-weld steels are ferrous alloys that are characterized by a low thermal conductivity, and large thermal expansion coefficient. These intrinsic features contribute to a high level of distortion and cracking susceptibility during joining of these types of steels. In an effort to address the issues associated with difficult-to-weld steels, highly concentrated beam spots like electron and laser beam welding were developed. Usage of tightly focused heat sources have been accompanied by several challenges. An extremely precise fit-up requirement was considered as the most significant issue corresponding to application of either laser or electron beam. Recently, it was found that the …

Human-Centered Electric Prosthetic (Help) Hand, Jamie Ferris, Shiyin Lim, Michael Mehta, Evan Misuraca

Interdisciplinary Design Senior Theses

Through a partnership with Indian non-profit Bhagwan Mahaveer Viklang Sahayata Samiti, we designed a functional, robust, and and low cost electrically powered prosthetic hand that communicates with unilateral, transradial, urban Indian amputees through a biointerface. The device uses compliant tendon actuation, a small linear servo, and a wearable garment outfitted with flex sensors to produce a device that, once placed inside a prosthetic glove, is anthropomorphic in both look and feel. The prosthesis was developed such that future groups can design for manufacturing and distribution in India.

Analytical And Experimental Study Of Laser Cladding Of Ni/Wc Metal Matrix Powders Reinforced With Rare Earth Elements Using A High Power Direct Diode Laser, Mohammed Sayeed

Mechanical Engineering Research Theses and Dissertations

The corrosion and wear are major limiting factors for steel in the harsh environments and can be controlled by depositing protective passive coatings. Nickel based alloy cladding of steel offers a solution by enabling better corrosion and wear resistance, and high bonding strength. The laser surface cladding of steel was conducted using a high power direct diode laser. Layers of tungsten carbide in Ni (40%Ni-60%WC) combined with 1% and 2% Lanthanum Oxide (La₂O₃) and Cerium Oxide (CeO₂) were deposited on ASTM A36 steel substrate. The X-ray diffraction and scanning electron microscopy were employed to …

Cal Poly Supermileage Electric Vehicle Drivetrain And Motor Control Design, Clarisa Joy Howe, Christopher Joseph Mclaughlin, Erik Alvarado, Enyi Liang

Mechanical Engineering

The Cal Poly Supermileage Vehicle team is a multidisciplinary club that designs and builds high efficiency vehicles to compete internationally at Shell Eco-Marathon (SEM). Cal Poly Supermileage Club has been competing in the internal combustion engine (ICE) category of the competition since 2007. The club has decided it is time to expand their competition goals and enter their first battery electric prototype vehicle. To this end, a yearlong senior design project was presented to this team of engineers giving us the opportunity to design an electric powertrain with a custom motor controller. This system has been integrated into Ventus, the …

Design, Control, And Optimization Of Robots With Advanced Energy Regenerative Drive Systems, Poya Khalaf

ETD Archive

We investigate the control and optimization of robots with ultracapacitor based regenerative drive systems. A subset of the robot joints are conventional, in the sense that external power is used for actuation. Other joints are energetically self-contained passive systems that use ultracapacitors for energy storage. An electrical interconnection known as the star configuration is considered for the regenerative drives that allows for direct electric energy redistribution among joints, and enables higher energy utilization efficiencies. A semi-active virtual control strategy is used to achieve control objectives. We find closed-form expressions for the optimal robot and actuator parameters (link lengths, gear ratios, …

Advanced Processing Of Nickel-Titanium-Graphite Based Metal Matrix Composites, Amit K. Patil

ETD Archive

A new class of in situ titanium carbide (TiC)/graphite (C) reinforced nickel matrix composites with variation in composition particularly varying C/Ti ratio have been processed using two different processing techniques. Firstly, via mechanical alloying (MA) followed by spark plasma sintering (SPS), i.e. solid-state processing. Secondly, using Laser engineered net shaping (LENSTM) technique, i.e. metal additive manufacturing technique. Mechanical alloying has gained special attention as a powerful non-equilibrium process for fabricating amorphous and nanocrystalline materials, whereas spark plasma sintering is a unique technique for processing dense and near net shape bulk alloys with homogeneous microstructure. Laser engineered net shaping (LENSTM) is …

A Reticulation Of Skin-Applied Strain Sensors For Motion Capture, Christopher A. Schroeck

ETD Archive

The purpose of this research is to develop a system of motion capture based on skin-applied strain sensors. These elastic sensors are of interest because they can be applied to the body without restricting motion and are well suited to operate in more practical environments, such as sports fields, gymnasiums, and outdoor areas. This combination is currently not available in the field of motion capture. The current issues with strain sensor motion capture technology is the accurate is not sufficient for motion analysis and axial rotation monitoring of joints is not available. This project will build and test a sensor …

Robust Impedance Control Of A Four Degree Of Freedom Exercise Robot, Santino Joseph Bianco

ETD Archive

The CSU 4OptimX exercise robot provides a platform for future research into advanced exercise and rehabilitation. The robot and its control system will autonomously modify reference trajectories and impedances on the basis of an optimization criterion and physiological feedback. To achieve this goal, a robust impedance control system with trajectory tracking must be implemented as the foundational control scheme. Two control laws will be compared, sliding mode and H-infinity control. The above robust control laws are combined with underlying impedance control laws to overcome uncertain plant model parameters and disturbance anomalies affecting the input signal. The sliding mode control law …

Theoretical Study Of Fano Resonance In A Mechanical System, Alex Alberts

Williams Honors College, Honors Research Projects

Resonance conditions are a major area of study in theoretical and experimental investigation. Normally, a resonance condition is characterized by a symmetric shape on either side of the resonance. In some cases, we can observe an asymmetric resonance shape, which is called a Fano resonance. We will study the appearance of Fano resonance in a purely mechanical system. The frequency response of the primary system is approximated using the method of multiple scales focusing on the location of the resonance condition. Then, curve fitting is used to approximate the Fano parameter associated with the system, which provides a measurement of …

Pick-And-Place Robot For The 2019 Asme Student Design Competition, Riniah A. Foor, Megan Schmit, Aaron Urban, Jeanetta Davidsaver, Daniel Mugongo

Williams Honors College, Honors Research Projects

This project was undertaken as an opportunity to participate in a holistic experience of designing, building, and competing as an engineering design team. In the ASME Student Design Competition, undergraduate students are able to experientially learn the process of design inception, manufacture, and product performance in addition to the development of critical project management skills. This is done through a creative design challenge to build a device capable of accomplishing a “pick-and-place” task in a fast and efficient manner.

Design And Manipulation Of A Power-Generating System With High-Temperature Fuel Cells For Hypersonic Applications, Jack Randolph Chalker

Browse all Theses and Dissertations

Current hypersonic vehicles tend to be incapable of producing onboard power with traditional generators due to their use of supersonic combusting ramjets (scramjets). Because of this, they seek additional energy sources for supporting advanced electronics or other auxiliary power-dependent devices while requiring elaborate thermal management systems to combat temperatures exceeding 700ºC. The incorporation of Solid Oxide Fuel Cell (SOFCs) stacks is an efficient solution, capable of generating large quantities of power through the use of natural fuel sources at high temperatures. Developments in this thesis include the design, construction, and support of a system operating at hypersonic-environment conditions with a …

Design And Implementation Of Periodic Unsteadiness Generator For Turbine Secondary Flow Studies, Nathan James Fletcher

Browse all Theses and Dissertations

A primary source of periodic unsteadiness in low-pressure turbines is the wakes shed from upstream blade rows due to the relative motion between adjacent stators and rotors. These periodic perturbations can affect boundary layer transition, secondary flow, and loss generation. In particular, for high-lift front-loaded blades, the secondary flowfield is characterized by strong three-dimensional vortical structures. It is important to understand how these flow features respond to periodic disturbances. A novel approach was taken to generate periodic unsteadiness which captures some of the physics of turbomachinery wakes. Using stationary pneumatic devices, pulsed jets were used to generate disturbances characterized by …

An Investigation On Spur Gear Rolling Contact Fatigue Crack Initiation And Crack Propagation Under Ehl Condition, Vignesh Dharmajan

Browse all Theses and Dissertations

Pitting is a rolling contact fatigue phenomenon commonly observed in mechanical rolling elements, such as gears and bearings. In case of gear contacts, pitting usually takes place in the dedendum region, where both sliding and contact load are high. In this study, a model is developed to predict surface breaking crack formation fatigue lives, including both nucleation and propagation stages, for spur gear contacts operating under mixed elastohydrodynamic lubrication (EHL) condition. The model utilizes a gear load distribution model for tooth contact Analysis. A mixed EHL formulation is implemented to evaluate the surface normal pressure and tangential shear, incorporating the …

Simulation, Experimentation, Control And Management Of A Novel Fuel Thermal System, Austin L. Tipton

Browse all Theses and Dissertations

Modern aircraft experience increasing thermal loads from electronics, electromechanical actuators, and directed energy weapons. These aircraft also have a reduced ability to transfer thermal energy to the atmosphere due to the use of composite skins and a limited number of air intake ports. For aircraft that use fuel as a heatsink, these factors can cause the fuel at points of the system to exceed temperature limits, which can result in fuel coking, damage to subsystems, and even complete system failure. This thesis investigates the fuel thermal management shortcomings of contemporary aircraft systems and suggests a new methodology to extend performance. …

Aerodynamics Of Fan Blade Blending, Clint J. Knape

Browse all Theses and Dissertations

Blending is a method of fan and compressor blade repair. The goal of the blending process is to remove stress concentration points such as cracks and nicks along the leading, trailing, or tip edges of the blade. The stressed areas are typically removed by grinding or cropping away the surrounding material. For integrally bladed rotor (IBR) disks, repairing a damaged blade is much more economical than replacing the entire disk. However, the change in shape of the blade will change the local aerodynamics and result in mistuning, both structurally and aerodynamically. In a worst case scenario, the change in the …

Analytical And Experimental Investigation Of Time-Variant Acceleration Fields, Justin A. Williams

Browse all Theses and Dissertations

Devices expected to operate in elevated or non-standard acceleration fields are often tested in similar conditions prior to deployment. Typically these tests only simulate steady-state acceleration fields in one direction. However, real acceleration fields often vary both directionally and temporally. Designing experiments to produce these conditions requires careful forethought and analysis in order to understand the emergent acceleration components that result from the methodology. An experiment was designed and executed on a horizontal centrifuge in which the radial acceleration varied sinusoidally between -10 < a_r < 10 g. Negative acceleration was achieved by rotating the test article relative to the radial acceleration vector using a servo motor. A model was developed that predicted the acceleration field at every point along the test article. The model provided important information such as the acceleration magnitude and direction anywhere on the test device at any point in time. This model was then used to optimize the velocity profile of the servo motor to minimize experimental artifacts.

Rasters Vs Contours For Thin Wall Ultem 9085 Fdm Applications, Vausman Kota

Browse all Theses and Dissertations

Currently many components are additively manufactured via fused deposition modeling (FDM). However, FDM results in gaps between passes which produces a poor surface finish and porous material that is difficult to hold pressure. Commercial scale air systems require a pressure to be maintained within thin walled components with minimal post processing and clean up after fabrication. A design of experiments (DOE) was created to identify the optimal raster vs contour ratio for UTLEM 9085 CG fabricated using FDM at different build angles and wall thicknesses. A custom-built pressurized test system was developed, the leak rates were calculated and the surfaces …

Adaptive Identification Of Classification Decision Boundary Of Turbine Blade Mode Shape Under Geometric Uncertainty, Ian M. Boyd

Browse all Theses and Dissertations

Integrally Bladed Rotors (IBR) of aircraft turbine engines suffer from fluctuations in the dynamic response that occurs due to blade to blade geometric deviations. The Stochastic Approach for Blade and Rotor Emulation (SABRE) framework has been used to enable a probabilistic study of mistuned blades in which a reduced order modeling technique is applied in conjunction with sets of surrogate models, called emulators, to make predictions of mistuned mode shapes. SABRE has proven useful for non-switching mode shapes. However, switching mode shapes have non-stationary or discontinuous response surfaces which reduce the accuracy of the surrogate models used in SABRE. To …