Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 13 of 13
Full-Text Articles in Entire DC Network
Effect Of Different Corrosion Inhibitors On The Corrosion Of Cast Iron In Palm Biodiesel
Effect Of Different Corrosion Inhibitors On The Corrosion Of Cast Iron In Palm Biodiesel
A.S. Md Abdul Haseeb
Biodiesel is currently in regular use as an alternative fuel over conventional petroleum diesel. However, corrosion of automotive materials is one of the concerns related to biodiesel compatibility issues. In addition, auto-oxidation of biodiesel can also enhance the corrosiveness of biodiesel. The present study aims to investigate inhibition effect of ethylenediamine (EDA), n-butylamine (nBA), tert-butylamine (TBA) against corrosion of cast iron. Static immersion tests in biodiesel in the presence (100 ppm) and absence of different corrosion inhibitors were carried out at room temperature for 1200 hours. At the end of the test, corrosion characteristic was investigated by weight loss measurements …
Effect Of Different Corrosion Inhibitors On The Corrosion Of Cast Iron In Palm Biodiesel
Effect Of Different Corrosion Inhibitors On The Corrosion Of Cast Iron In Palm Biodiesel
A.S. Md Abdul Haseeb
Biodiesel is currently in regular use as an alternative fuel over conventional petroleum diesel. However, corrosion of automotive materials is one of the concerns related to biodiesel compatibility issues. In addition, auto-oxidation of biodiesel can also enhance the corrosiveness of biodiesel. The present study aims to investigate inhibition effect of ethylenediamine (EDA), n-butylamine (nBA), tert-butylamine (TBA) against corrosion of cast iron. Static immersion tests in biodiesel in the presence (100 ppm) and absence of different corrosion inhibitors were carried out at room temperature for 1200 hours. At the end of the test, corrosion characteristic was investigated by weight loss measurements …
Influence Of Ni Nanoparticle On The Morphology And Growth Of Interfacial Intermetallic Compounds Between
A.S. Md Abdul Haseeb
TiO2 thin films were deposited on unheated and heated glass substrates at an elevated sputtering pressure of 3 Pa by radio frequency (RF) reactive magnetron sputtering. TiO2 films deposited at room temperature were annealed in air for 1 h at various temperatures ranging from 300 to 600 °C. The structural and optical properties of the thin films were investigated using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and ultraviolet-visible-near infrared (UV-VIS-NIR) spectrophotometry. XRD results show that as-grown and post-annealed TiO2 films have anatase crystal structure. Higher substrate and annealing temperatures result in a slight increase of crystallinity. TiO2 …
Liga Fabrication Of Nanocrystalline Ni-W Alloy Micro Specimens From Ammonia-Citrate Bath
Liga Fabrication Of Nanocrystalline Ni-W Alloy Micro Specimens From Ammonia-Citrate Bath
A.S. Md Abdul Haseeb
Ammonia-citrate bath has been investigated for the deposition of nano crystalline Ni-W alloy micro components using the LIGA process. First the bath stability and deposit characteristics were studied. Fabrication of micro specimens were then carried out on silicon substrates covered with novolac as well as thick PMMA resist for LIGA. Effects of different parameters like current density, nickel ion and tungsten ion concentration in the bath, deposition time etc. on the deposit characteristics and current efficiency were studied. The deposited Ni-W samples were characterized by scanning electron microscopy, energy depressive X-ray spectroscopy, light optical microscopy and X-ray diffraction. Results show …
Liga Fabrication Of Nanocrystalline Ni-W Alloy Micro Specimens From Ammonia-Citrate Bath
Liga Fabrication Of Nanocrystalline Ni-W Alloy Micro Specimens From Ammonia-Citrate Bath
A.S. Md Abdul Haseeb
Ammonia-citrate bath has been investigated for the deposition of nano crystalline Ni-W alloy micro components using the LIGA process. First the bath stability and deposit characteristics were studied. Fabrication of micro specimens were then carried out on silicon substrates covered with novolac as well as thick PMMA resist for LIGA. Effects of different parameters like current density, nickel ion and tungsten ion concentration in the bath, deposition time etc. on the deposit characteristics and current efficiency were studied. The deposited Ni-W samples were characterized by scanning electron microscopy, energy depressive X-ray spectroscopy, light optical microscopy and X-ray diffraction. Results show …
Study Of The Wear Behaviour Of Al-4.5% Cu-3.4% Fe In Situ Composite: Effect Of Thermal And Mechanical Processing
A.S. Md Abdul Haseeb
Al-Cu-based MMCs reinforced by Al-Fe intermetallics are investigated for their wear behaviour. The composite (Al-4.5 mass% Cu-3.4 mass% Fe) was produced by solidification processing where the Al-Fe-based intermetallic formed in situ in a matrix of mainly Al-Cu alloy. The effects of thermal and mechanical processing, viz., as-cast condition, solution treatment, aging and hot rolling on the wear behaviour of the composites were examined. The composites were characterized by optical microscopy, SEM, microhardness measurements and X-ray diffraction. The wear behaviour of the composites was studied in a pin-on-disc type wear apparatus. The as-cast in situ composite exhibited the highest wear rate. …
A Technical Note On The Production Of Zirconia And Zircon Brick From Locally Available Zircon In Bangladesh
A.S. Md Abdul Haseeb
In this study, the potentiality of Bangladesh zircon as a raw material for zirconia and zircon brick production was examined. Decomposition of zircon (ZrSiO4) into zirconia (ZrO2) was attempted by using caustic soda (NaOH) as the decomposition agent. 5-10 μm size zircon, 5-30 wt.% NaOH, and decomposition temperatures ranging from 1300 to 1500°C were investigated. X-ray diffraction method using Mo Kα radiation was used in order to find out the extent of decomposition of zircon into zirconia. Zircon bricks of 0.06 mm× 0.06 mm× 0.025 mm shaped were made under a pressure of 15 MPa. Carboxi methyal cellulose (CMC) and …
Failure Analysis Of Superheater Tube Supports Of The Primary Reformer In A Fertilizer Factory
Failure Analysis Of Superheater Tube Supports Of The Primary Reformer In A Fertilizer Factory
A.S. Md Abdul Haseeb
A failure analysis of superheater tube supports of the primary reformer in a local fertilizer factor is presented. A number of tube supports failed at approximately half of their designed service life. Following the failure, the factory was visited, and relevant information and samples were collected. The samples were investigated in the laboratory by chemical analysis, macro- and microhardness measurements, macro-and micrometallographic examinations, and X-ray diffractometry. The analysis showed the supports were fabricated from HH-type heat-resisting alloy and that the failure mode was high-temperature creep. The microstructure of the alloy showed the presence of massive intergranular as well as intragranular …
On The Nature Of The Electrochemically Synthesized Hard Fe-0.96 Mass Pct C Alloy Film
On The Nature Of The Electrochemically Synthesized Hard Fe-0.96 Mass Pct C Alloy Film
A.S. Md Abdul Haseeb
A hard Fe-0.96 mass pet C alloy with a hardness value of 810 HV has been electrochemically synthesized from a ferrous sulfate bath containing a small amount of citric acid and L-ascorbic acid. The nature of the alloy has been investigated by a number of techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Mössbauer spectroscopy, differential scanning calorimetry (DSC), and magnetic measurements. The decomposition behavior of the alloy is also studied and compared with that of thermally prepared martensite. It has been found that the electrochemically deposited Fe-C alloy exists in …
On The Nature Of The Electrochemically Synthesized Hard Fe-0.96 Mass Pct C Alloy Film
On The Nature Of The Electrochemically Synthesized Hard Fe-0.96 Mass Pct C Alloy Film
A.S. Md Abdul Haseeb
A hard Fe-0.96 mass pet C alloy with a hardness value of 810 HV has been electrochemically synthesized from a ferrous sulfate bath containing a small amount of citric acid and L-ascorbic acid. The nature of the alloy has been investigated by a number of techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Mössbauer spectroscopy, differential scanning calorimetry (DSC), and magnetic measurements. The decomposition behavior of the alloy is also studied and compared with that of thermally prepared martensite. It has been found that the electrochemically deposited Fe-C alloy exists in …
A Comparative Wear Study On Heat-Treated Aluminium-Lithium Alloy And Pure Aluminium
A Comparative Wear Study On Heat-Treated Aluminium-Lithium Alloy And Pure Aluminium
A.S. Md Abdul Haseeb
Wear behaviour of solution-treated and aged aluminium-lithium alloy (2.5% Li, 2% Cu, 1% Mg and 0.15% Zr) was compared with that of pure aluminium. Wear tests were carried out in ambient air in a pin-on-disc type apparatus under dry sliding conditions using hardened steel disc as the counterbody. A normal load of 10 N and a linear speed of 0.98 m s-1 were used during the tests. Microscopic investigation, microhardness measurement on the subsurface of wear scars on pins, X-ray diffraction study and morphological examination of wear debris were done to elucidate wear mechanism. It has been found that the …
Xrd, Xps And Sims Investigations On Electrodeposited Nickel-Phosphorous Alloy Coatings
Xrd, Xps And Sims Investigations On Electrodeposited Nickel-Phosphorous Alloy Coatings
A.S. Md Abdul Haseeb
Structural and chemical investigations on electrodeposited nickel-phosphorous alloy coatings by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS) are described. Electrodeposition of nickel-phosphorous coatings has been carried out galvanostatically in a hypophosphite bath at two different current densities, namely 20 and 80 mA cm -2. XRD has shown a broad peak indicating an amorphous structure in both cases. XPS shows the presence of Ni 2P compound. XPS also reveals the amount of phosphorous in both coatings to be around 10.20 wt.%. SIMS has shown that the coating deposited at lower current density (20 mA cm …
Study Of The Wear Behaviour Of Al-4.5% Cu-3.4% Fe In Situ Composite: Effect Of Thermal And Mechanical Processing
A.S. Md Abdul Haseeb
Wear behaviour of as-cast and heat-treated spheroidal graphite (SG) cast iron has been studied under dry sliding conditions using a pin-on-disc type apparatus. Wear tests were carried out at a linear sliding speed of 0.88 m s -1, under a constant load of 1.5 kg. All tests were performed in ambient air at room temperature. Extent of wear damage and wear mechanisms were investigated by means of weight loss measurement, optical microscopy, microhardness measurement and X-ray diffractometry on wear debris. The wear rate measured after 9500 m of sliding is found to be about three times higher in the as-cast …