Digital Commons Network^™

Creating Reel Designs: Reflecting On Arthrogryposis Multiplex Congenita In The Community, Iris Layadi

Purdue Journal of Service-Learning and International Engagement

Because of its extreme rarity, the genetic disease arthrogryposis multiplex congenita (AMC) and the needs of individuals with the diagnosis are often overlooked. AMC refers to the development of nonprogressive contractures in disparate areas of the body and is characterized by decreased flexibility in joints, muscle atrophy, and developmental delays. Colton Darst, a seven-year-old boy from Indianapolis, Indiana, was born with the disorder, and since then, he has undergone numerous surgical interventions and continues to receive orthopedic therapy to reduce his physical limitations. His parents, Michael and Amber Darst, have hopes for him to regain his limbic motion and are …

Electrical Characterization Of Phytoplankton Suspensions Using Impedance Spectroscopy., Margaret R Jett

Electronic Theses and Dissertations

Phytoplankton are closely monitored because of their important environmental role, and the impacts they have on their local ecosystems. Some phytoplankton respond to stress by producing lipids, which can be harvested for biofuels and other chemicals. Microfluidic devices have been important in improving the portability and throughput of phytoplankton characterization methods, increasing their potential for in situ use. This study utilized a small sample of phytoplankton suspended in a stagnant medium and measured the impedance response using a lab-on-chip and impedance analyzer. The individual cell characteristics were derived from the impedance response of the group. The goal was to characterize …

Material Detection With Thermal Imaging And Computer Vision: Potentials And Limitations, Jared Poe

Graduate Theses and Dissertations

The goal of my masters thesis research is to develop an affordable and mobile infraredbased environmental sensoring system for the control of a servo motor based on material identification. While this sensing could be oriented towards different applications, my thesis is particularly interested in material detection due to the wide range of possible applications in mechanical engineering. Material detection using a thermal mobile camera could be used in manufacturing, recycling or autonomous robotics. For my research, the application that will be focused on is using this material detection to control a servo motor by identifying and sending control inputs based …

Frequency Domain Measurements Of Melt Pool Recoil Force Using Modal Analysis, Tristan Cullom, Cody Lough, Nicholas Altese, Douglas Bristow, Robert Landers, Ben Brown, Troy Hartwig, Andrew Barnard, Jason Blough, Kevin Johnson, Edward Kinzel

Michigan Tech Publications

Recoil pressure is a critical factor affecting the melt pool dynamics during Laser Powder Bed Fusion (LPBF) processes. Recoil pressure depresses the melt pool. When the recoil pressure is low, thermal conduction and capillary forces may be inadequate to provide proper fusion between layers. However, excessive recoil pressure can produce a keyhole inside the melt pool, which is associated with gas porosity. Direct recoil pressure measurements are challenging because it is localized over an area proportionate to the laser spot size producing a force in the mN range. This paper reports a vibration-based approach to quantify the recoil force exerted …

Human Powered Vehicle Capstone, Maya L. Washington, Ryan Apolonio, Marc Sunga, John Rettenmier, Dr. Allen Wilson

Honors Thesis

In the ASME Human Powered Vehicle Challenge (HPVC), students design, develop, construct, and test different designs of human-powered vehicles. The design utilizes two wheels, the rear of which is responsible for power transmission from a pedal crank and braking through a disc and caliper. The design also utilizes the front wheel fork wheel for steering. Steering and braking are controlled by two levers on the handlebars. To determine whether the design was sufficient, it was compared to the standards set by ASME, including maximum weight, minimum speed, minimum turning radius, minimum ride distance, load testing, harness verification, and a complete …

Monitoring Of Overhead Polymer Core Composite Conductors Under Excessive Mechanical Loads Using Fiber Bragg Grating Sensors, Daniel H. Waters

Electronic Theses and Dissertations

This combined experimental and numerical study addresses mechanical effects associated with static and dynamic loading of novel High Temperature Low Sag (HTLS) transmission line polymer core composite conductors. The developed methodology was successfully applied to ACCC® to explain the complex failure mechanisms associated with combined bending and tension loading. Furthermore, the use of Fiber Bragg Grating (FBG) sensors was investigated for the first time to monitor the ACCC® design during installation and in-service.

Transverse low-velocity impacts to the ACCC® conductor having either free or constrained end conditions and large axial tensile loads were performed. It was identified that the most …

Sources Of Quality Uncertainty In Laser Powder Bed Fusion Metal Additive Manufacturing, Zachary Young

Doctoral Dissertations

"Powder based additive manufacturing (AM) exhibits tremendous uncertainties, where variations in build quality is present despite utilizing similar build processing parameters. First, this work reports the features and formation mechanisms of five unique types of spatter during the LPBF process by in-situ high-speed, high-energy x-ray imaging. The unique physical characteristics of spatter are determined. The effect of laser scan speed and laser power on spatter formation, ejection, and mitigation are determined. Second, this work addresses the uncertainty challenge by identifying the sources of uncertainty in SLM by in-situ characterization due to variations from the additive manufacturing processing parameters needed for …

Customizable Armor Set, Olivia Reedy

Williams Honors College, Honors Research Projects

This project is intended to help people who make costume armor by reducing the amount of time and money it takes to create a set of armor. Making armor can take a lot of resources for beginners, and this project is intended to help hobbyists with that process. This customizable armor set goes through the engineering design process, from the initial design of the parts to creating the prototype using vacuum forming. The prototype armor can be painted and adhered to using acrylic paint and contact cement, respectively, and fits three sizes of small, medium, and large.

Development Of An Undergraduate Welding Laboratory For Research And Education, Hamid Eisazadeh, Alok K. Verma

Engineering Technology Faculty Publications

The shortage of welders in Hampton Roads area, where many shipyards are located, is becoming severe for shipbuilding in coming years. Many welding engineers graduated from universities located out of state, tend to go back to companies near their home, after receiving couple years of welding experience at Hampton Roads shipyards. Therefore, it is critical to train local welders. In order to address the welding workforce needs of Hampton Roads, the Department of Engineering Technology at Old Dominion University has recently launched an initiative for developing a laboratory for welding processes (LWP) for supporting educational and research activities in its …