Digital Commons Network^™

Research Of Physical And Mechanical Properties Of Babbits Filled In Sliding Bearings, K G. Gaparov

Scientific-technical journal

The article presents the results of research of physical and mechanical properties of babbites prepared from scrap and wastes poured into sliding bearings. The development of the technology of recycling scrap and babbites waste is aimed at optimizing the parameters of the technology of cleaning and melting babbites for reuse of so-called secondary babbites.

Mathematical Model Of The Efficiency Of Investments Aimed In The Implementation Of Water-Saving Technologies

Irrigation and Melioration

In Uzbekistan, research work is being carried out aimed at improving the economic mechanisms for the introduction of water-saving technologies for irrigating agricultural crops. At the same time, the issues related to the analysis of the effectiveness of the use of water-saving technologies when irrigating cotton, the development of mathematical methods for assessing the effectiveness of investments, as well as their introduction into practice have not been sufficiently studied. This article provides a mathematical model of the efficiency of investments aimed at introducing water-saving technologies. The results of a numerical experiment of a mathematical model show that the introduction of …

Efficient Use Of Water Resources In The Basins Of Small Rivers, F. Gapparov, M.F. Gafforova

Irrigation and Melioration

The article provides a recommendation for the efficient use of water resources in the basins of small foothill rivers. The research was carried out on the example of the Govasay river basin located in the northern part of the Fergana Valley. The efficiency factor of the canal has been determined and a technical assessment has been given for the management of water resources in the river basin; the efficiency of the canal is 65-75%. A program for the operational management of water resources in The Govasay river basin and a GIS map of water consumers in the Govasay river basin …

Model Of Groundwater Level Control Using Horizontal Drainage, A. Arifjanov, M. Otaxonov, Z. Abdulkhaev

Irrigation and Melioration

The article describes the main factors affecting the rise in the level of groundwater in the city of Fergana and ways to eliminate them. Currently, in order to reduce the negative impact of rising groundwater levels on the environment, crops, buildings and structures, as well as underground utilities, it is proposed to design horizontal drainage in urban areas and a mathematical model has been developed for changing the groundwater level. For this, long-term data from observation wells were analyzed and the hydraulic parameters of horizontal drainage were selected taking into account the hydrogeology of the area. Taking into account the …

Results Of Proximate Analysis Of Energy Use Of Municipal Solid Waste, N.N. Abduganiev

Irrigation and Melioration

In the modern industrialized world, various raw materials are processed and used for human consumption. While some of the raw materials are converted into the desired product, the rest is thrown into the environment as waste. It is known that solid waste is a type of biomass that is formed in the course of human life. The article presents the results of a preliminary analysis of studies on the use of solid waste energy in the Urta-Chirchik district of the Tashkent region. Sorting results showed that the total volume of municipal solid waste in the district consists mainly of wood …

Shredding Of Cotton Stalks Under The Action Of Toothpicks In A Combined Unit, B. Khudayarov, U. Kuziev, B. Sarimsakov, М. Kholbutaev

Irrigation and Melioration

The article presents materials devoted to the justification of the parameters of the crown-wheel of the combined aggreagate. The technological process of work and the design of the working part, which is crushed by crushing cotton stalks, without breaking them, laying them on the movement of the unit, has been substantiated and developed. The optimal parameters of the crown-wheel and the tooth are determined by solving the regression equations that determine the optimal values of the vertical load on the teeth and its working quality. The results of theoretical and experimental research show that the amount of crushing of cotton …

Influence Of Electrophysical Methods On The Processes Of Root Formation Of Grapes, N.M. Markayev

Irrigation and Melioration

The article describes the possibilities of electrophysical processing before planting cuttings during vegetative cultivation of grape seedlings. The processes of root formation in cuttings using the electrophysical method in the article Acceleration of the process of root formation in cuttings of black raisins, treated at 71 V/m and an electric field strength of 15 hours, and an increase in the viability, quality, growth and survival of rooted seedlings up to 16.67-34% Presented the results of experiments on the increase and methods of electrotechnological processing of grape cuttings. The result of the study is the analysis and results of the processes …

Conditions, Criteria And Principles For Creating An Agri-Cultural Land Market In Uzbekistan, A.R. Nurnazarov

Irrigation and Melioration

The article analyzes the prerequisites for creating a market for agricultural land in the Republic of Uzbekistan, special attention is paid to land reform, land degradation (reduction of the bonitet score from 60 in 1991 to 50 or more at present, pasture degradation by 20-30%) and increase in economic from their use, the role of land rent in payments for land. 6 basic principles for creating a land market have been established and systematized, the relationship between X-rays and water in the irrigated farming zone, the role of the market in increasing the efficiency and effectiveness of the use of …

Economic Assessment Of The Effect Of Family Income On Students' Disciplines, Sh.A. Muratov

Irrigation and Melioration

The importance of higher education in scientific research, its role in poverty reduction and population growth has been studied theoretically. Also, when using the data of social surveys conducted by 538 respondents (students) studying in higher education institutions, they were awarded the Order of the logistics regulator in the economic assessment of the factors influencing the rate of mastery of disciplines. Factors influencing the acquisition of subjects by students: the main income of the family comes from non-farm (69,9 %), sex (52,2 %), studying at a higher education institution on a state grant (108,8 %), the student's course of study …

Innovative Rotor Casing And Leveling Apron For Combined Tillage Machine, A.A. Akhmetov, L.B. Muratov

Irrigation and Melioration

Investigations of the design of a combined machine equipped with an innovative casing and a leveler apron are presented, and the parameters of the leveler apron are substantiated. It was experimentally established that when the height of the drawing prism is exceeded by more than 200 mm, due to the falling of the crumbling part of the soil onto the rotor, the soil is thrown forward in the direction of the machine. Therefore, to eliminate soil waste, it is necessary either to reduce the height of the drag prism, or to increase the distance between the rotor and the leveling …

Ensuring The Uniformity Of Movement Of The Working Bodies Of The Machine For Processing Ridges In The Depth Of Travel, А. Tukhtakuziev, K.G. Abdulkhaev

Irrigation and Melioration

The article theoretically investigates the issue of identifying ways to ensure the deepening of the working bodies of the machine for processing ridges to a given processing depth and its required uniformity of stroke. The research results show that the deepening of the working bodies of the ridges processing machine to a given processing depth and its required uniformity is provided mainly due to the correct choice of the vertical distance from its reference plane to the lower connection points. The novelty of the conducted research lies in the fact that an analytical dependence has been obtained that allows us …

Develepment Of Land Market In Eastern European Countries And Experience For Uzbekistan, A.R. Nurnazarov

Irrigation and Melioration

The article examines the experience of the formation of the agricultural land market in Eastern European countries since the 90 s of the twentieth century, the problems and features of its devel-opment, the impact of the land market on the economies of countries. Particular attention is paid to the transformation of land ownership, methods of land privatization, land pricing, restrictions on land purchase, regulation of land relations in market conditions, issues of granting the right to pur-chase land to foreign individuals and legal entities, requirements for land owners for the presence of a special agricultural education or 3-5 years of …

The Developmet Of Competences Via Techniques For Enhancing Esp (English For Specific Purposes) Vocabulary Of Learners, G. Eshchanova

Irrigation and Melioration

In the article a recent trend in higher education is ESP (English for Specific Purposes) courses is discussed. These courses are designed around students’ needs based on their field of study. The goal is to strengthen students’ proficiency and help them to get ready to cope with everyday situations and deal with professionals in many fields such as: engineering, medicine, education and IT. There are many training sessions organized by international experts whose goal is to train local teachers to teach these courses successfully. In order to develop an ability to learn new vocabulary, for both general English and technical …

Development Of Girls’ Sports, A.R. Khodjanov, V.V. Mahmudov

Irrigation and Melioration

The article addresses current issues of higher education, taking into account its specifics. She has been providing appropriate advice on improving girls' physical well-being. The use of opportunities and qualities has an impact on the creation of comfortable conditions for female athletes. For girls involved in sports, the creation of impressive quality and possible conditions is considered. As a result, the girls-athletes of our institute took 2-3 places in the district and city qualifying rounds of chess, table tennis and won a ticket to the republican stage. At the republican stage, 2 female students of our team took 4th place …

The Imrovement Of Esp Teaching Via Methodical Provision At Technical Institution: Specializm-Oriented English Via Agriculture, G. Eshchanova, U. Nullaev

Irrigation and Melioration

In the given article the ways that ESP combines subject matter and English language teaching is discussed. This approach can be highly motivating for students because students are able to apply what they learn in their English classes to their main field of study, whether it be law, computing, business, tourism, etc. Being able to use the vocabulary and structures that they learn in a meaningful context reinforces what is taught and increases their motivation. Nevertheless, ESP concentrates more on language in context than on teaching grammar and language structures. Additionally, the ways of teaching English in ESL classes and …

Evaluation Of The Thickness Of Vacuum Metal And Semiconductor Coatings Using Computer Programs, Bahrom Igamov, Ilkhom Bekpulatov, Aleksey Kamardin, Tulkun Kamilov, Ilhom Turapov, D Igamova

Technical science and innovation

Comparative studies of the thickness of coatings of such metals as Cu, Ag, Cr, Co, and also Mn4 Si7 on polished substrates made of Si, Si O2 / Si structure, ST - 50 glass ceramic, mica were carried out. The coatings were deposited in vacuum using thermal evaporation and magnetron sputtering. The thickness and uniformity of deposited coatings on rotating substrates are estimated by optical measurements and computer simulation. Mathematical models for the formation of coatings on flat substrates have been developed. The possibility of the optimal position of the substrate for the formation of functional coatings uniform in thickness …

Study Of The Thermodynamic Properties Absorbation Sulfur Storage Gas Of Zinc And Copper Industry, Berdiyarov Tilovkabulovich Berdiyarov Dr., Sh. T. Khojiev, S. T. Matkarimov, Sh. Munosibov

Technical science and innovation

The article considers the problems of utilization of industrial gases formed in the production of copper and ore containing sulfur anhydrides. Currently, the composition of process gases entering the gas purification department is approximately 6-7% SO₂, 0.2-0.3% SO₃ and other gases, until sulfuric acid is obtained from these gases, the sulfate is treated in a counter-scheme with 8% sulfate acid. The aim is to first reduce the temperature of the exhaust gases and second to avoid flying components such as as As, F, Se. As a result of the studies, the amount of SO₂ in the …

Research Of Hydrodynamic Processes When Drying Mineral Fertilizers In Drum Dryers, R J. Tojiyev, A A. Akhunbaev, R X. Mirsharipov

Scientific-technical journal

The article discusses the experimental kinetics of the process of thermal drying of dispersed materials. Experimental methods for determining the periods of drying and kinetics of the process have been studied.

Dioxins Contamination In Sediment And Their Effect On Accumulation In The Portuguese Oyster (Crassostrea Angulata) And White Shrimp (Litopenaeus Vannamei), Yin-Yu Chen, Yu-Sheng Wu, Hsiang-Yin Chen, Zhen-Hao Liau, Fan-Hua Nan

Journal of Marine Science and Technology

This research aims to realize whether the dioxin accumulation in the oyster and white shrimp which were cultured in the dioxin pollutant sediment. This presented evidence indicated that dioxin was detected in all experimental groups with high concentration accumulated in experiment animals. Observation of the concentration, the PCDD/F, 2,3,7,8-T4CDD was with high concentration in the sediment and declined with the time elapsed. Detection of the dioxin accumulated in the animal, the accumulative maximum amounts was in the oyster as 3746.16 (pg-TEQ/g d.w.) and in the shrimp as 705.44 (pg-TEQ/g d.w.). The detected amount of dioxin in the supernatant was quite …

A Meshless Method With Radial Basis Function For Solving Unsaturated Flow In Heterogeneous Porous Media, Cheng-Yu Ku, Chih-Yu Liu, Wei-Po Huang, Jing-En Xiao

Journal of Marine Science and Technology

This paper presents a study for solving unsaturated flow in heterogeneous porous media using the meshless method with the radial basis function (RBF). For modeling the nonlinear hydrological process in unsaturated zone, an exponential model is introduced in the Richards equation such that we may obtain the linearized Richards equation. We adopt the multiquadric function as the RBF in the meshless method for solving the linearized Richards equation. For simulating the unsaturated flow problems in layered heterogeneous soils, the flux and the head must satisfy the continuity condition at the interface. Several examples are carried out for modeling the hydrological …

Catch Rates And Distribution Pattern Of The Silky Shark, Carcharhinus Falciformis, Caught By The Taiwanese Large-Scale Longline Fishery In The Indian Ocean, Chia Yun Li, Xing-Han Wu, Shang Yin Vanson Liu, Sheng-Ping Wang, Wen-Pei Tsai

Journal of Marine Science and Technology

The silky shark, Carcharhinus falciformis, is widely distributed in tropical and temperate waters, and it is a common bycatch species for tuna longline fisheries. This study examined the distribution of and presents relative abundance indices of the silky shark in the Indian Ocean by using logbook and observer data from the Taiwanese large-scale tuna longline fishery between 2005 and 2019. Due to the high zero catch rate, a zero-inflated negative binomial (ZINB) model was used to standardize catch per unit effort. Due to a lack of detailed targeting information, the fishery strategy was identified by using cluster analysis based on …

Accumulation And Bioavailability Of Heavy Metals (Cadmium, Chromium, Nickel, Lead And Zinc) In Water And Sediment Samples In The Musa Creek, Northwest Coasts Of The Persian Gulf, Saghafiankhoo Sedigheh, Battaleb-Looie Sedigheh, Amanipoor Hakimeh, Dravishi Khatooni Javad, Ghanemi Kamal

Journal of Marine Science and Technology

The current study aimed to investigate the total concentrations of heavy metals in water and sediment samples as well as their bioavailability in sediments of Musa Creek. Twenty samples including 10 sediments and 10 water samples were collected from 10 stations. The concentration of heavy metals was measured using inductively coupled plasma–mass spectrometry. The bioavailability of heavy metals was carried out by first step of Tessier sequential extraction method so called single extraction in the manuscript. The results showed that the mean concentrations of cadmium, chromium, nickel, and zinc in water samples was 0.17, 7.44, 43.80, and 8.85 µg/L, respectively. …

Parametric Analyses Of The Dynamic Response And Fatigue Life Of A Compliant Vertical Access Riser With Internal Flow, Fuheng Li, Haiyan Guo, Xiaomin Li, Zhen Liu, Honglu Gu, Peng Cui

Journal of Marine Science and Technology

Subsea interventions on wellheads can be directly performed from a platform using a compliant vertical access riser (CVAR), thereby incurring tremendous economic benefits. The dynamic response and the fatigue damage of a CVAR subjected to regular waves are important for assessing its application feasibility. Therefore, a reasonable numerical model is presented for assessing the damage to a CVAR considering the internal flow using the slender rod theory. The finite element method combined with a Newmark-β scheme is employed to discretize the equations and update the time integration. The Palmgren-Miner rule is applied for fatigue life prediction, focusing on the wave-induced …

Using The Inverse Method To Investigate Flow Models For Mixed Convection Of Annular Finned Tube Heat Exchanger, Han-Taw Chen, Cheng-Hui You, Wei-Lun Hsu, Jiang-Ren Chang

Journal of Marine Science and Technology

The inverse heat conduction method (IHCM) and three-dimensional (3D) computational fluid dynamic (CFD) in combination with are used to select the appropriate flow model and near-wall treatment for the mixed convection of the annular finned tube heat exchanger. Thus, the numerical results obtained by all k-ε models and near-wall treatments are yielded for 4 m/s ≤ Va ≤ 5 m/s. First, IHCM combined with is applied to estimate and Q values. The obtained estimates of and Q are used as reference values for CFD. The results show that the Tk and results obtained by the standard (STD) k-ε model with …

Prediction Of Remaining Useful Life Of Wind Turbine Shaft Bearings Using Machine Learning, Jinsiang Shaw, Bingjie Wu

Journal of Marine Science and Technology

Wind turbines are a major trend in the current green energy market. Wind energy is abundant, and if utilized properly, can result in significant reductions in carbon emissions. Therefore, the development of wind power systems is urgently required. However, wind turbines are mainly built in unmanned areas. Regular inspections require substantial manpower and material resources, and doubts regarding the accuracy of the inspected data may occur. Therefore, it is necessary to establish an automatic diagnostic method for determining the remaining useful life (RUL) of a wind turbine to facilitate predictive maintenance. In this study, a multi-class support vector machine (SVM) …

Supply Chain Management For Superyacht Construction In Taiwan, Chun Pong Wong

Journal of Marine Science and Technology

In the last 20 years, Taiwan’s superyacht construction industry has performed well in the global market; however, numerous yacht builders still practice traditional supply chain management (SCM), which is often inefficient and regularly leads to time and cost overruns. This study aimed to answer two research questions: 1) what SCM challenges does the superyacht construction industry face? and 2) what SCM strategies and practices should be adopted to improve the efficacy and profitability of superyacht construction companies?

Numerous studies have explored supply chains (SCs) and SCM, but few have focused on the superyacht construction industry. Superyacht construction projects are highly …

The Impact Of Variable Curing Conditions On The Properties And Microstructures Of Mixtures Of Ground Granulated Blast Furnace Slag And Circulating Q1 Fluidized Bed Combustion Ash, Shao-Heng Hsieh, Wei-Chung Yeih, Ran Huang

Journal of Marine Science and Technology

The use of Portland cement, an important construction material, is encountering growing challenges because of its adverse environmental impacts. In this study, a new hydration system without Portland cement, which blends ground granulated blast furnace slag (GGBFS) and circulating fluidized bed combustion (CFBC) ash, was developed and tested. The variables included the effect of different types of CFBC ash, the mass ratios between CFBC ash and GGBFS, and different curing temperatures. The mortar properties were determined through the compressive strength test, absorption test, shrinkage test, X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The main results were as follows: …

A Marine Gis-Based Alert System To Prevent Vessels Collision With Offshore Platforms, Sheng-Long Kao, Ki-Yin Chang, Tai-Wen Hsu

Journal of Marine Science and Technology

How to effectively use an intelligent aid-to-navigation (AtoN) to prevent ships from accidentally colliding with offshore marine platforms (OMPs) is an important issue for maritime environment. This study proposes a novel collision alert system with three components to process Automatic Identification System (AIS) data in the cloud and broadcast AtoNs to ships in order to avoid collision with OMPs. The first component receives as input fuzzy linguistic variables (vessel size, relative speed, and approach distance) from the AIS data and calculates the radius of the guarding ring. The second component serves a Marine GIS (MGIS), where the system simulates the …

Experimental Verification On The Effectiveness Of Random Vibration Testing With Controlling Acceleration And Velocity Kurtosis, Daichi Nakai, Katsuhiko Saito

Journal of Applied Packaging Research

Random vibration tests for packages are conducted to confirm the safety of these packages during shipping. In our previous study, a method of generating the random vibration controlling the power spectral density and kurtosis of acceleration and the kurtosis of velocity was proposed. The aim of the present study is to verify the effectiveness of the proposed method. Three vibrations were generated in this study and compared with the real vibration, which replicates the truck bed. In the first case, control of the acceleration and velocity kurtosis was neglected. In the second case, the vibration controlling the acceleration kurtosis was …

Theoretical Bases Of Diagnostics Of Radiators By Heat Load Of Passenger Cars, U R. Salomov, D A. Moydinov, S M. Yusupov

Scientific-technical journal

This article presents the technical characteristics of the phenomena occurring in the radiator pipes under the influence of the thermal regime of mechanisms determined by the technical condition of the cooling system components of cars with internal combustion engines.