Digital Commons Network^™

A Super-Hard High Entropy Boride Containing Hf, Mo, Ti, V, And W, Suzana Filipovic, Nina Obradovic, Greg E. Hilmas, William G. Fahrenholtz, Donald W. Brenner, Jon Paul Maria, Douglas E. Wolfe, Eva Zurek, Xiomara Campilongo, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Super-Hard (Hf,Mo,Ti,V,W)B2 Was Synthesized by Boro-Carbothermal Reduction and Densified by Spark Plasma Sintering. This Composition Was Produced for the First Time as a Single-Phase Ceramic in the Present Research. the Optimized Ceramic Had a Single Hexagonal AlB2-Type Crystalline Phase with a Grain Size of 3.8 µm and Homogeneous Distribution of the Constituent Metals. the Vickers Hardness Exhibited the Indentation Size Effect, Increasing from 27 GPa at a Load of 9.8 N to as High as 66 GPa at a Load of 0.49 N. This is the Highest Hardness Reported to Date for High Entropy Boride Ceramics.

Atomic Layer Deposition Of Sodium Fluoride Thin Films, Sara Kuraitis, Donghyeon Kang, Anil U. Mane, Hua Zhou, Jake Soares, Jeffrey W. Elam, Elton Graugnard

Materials Science and Engineering Faculty Publications and Presentations

The need for advanced energy conversion and storage devices remains a critical challenge amid the growing worldwide demand for renewable energy. Metal fluoride thin films are of great interest for applications in lithium-ion and emerging rechargeable battery technologies, particularly for enhancing the stability of the electrode-electrolyte interface and thereby extending battery cyclability and lifetime. Reported within, sodium fluoride (NaF) thin films were synthesized via atomic layer deposition (ALD). NaF growth experiments were carried out at reactor temperatures between 175 and 250 °C using sodium tert-butoxide and HF-pyridine solution. The optimal deposition temperature range was 175–200 °C, and the resulting …

X-Ray Determination Of Compressive Residual Stresses In Spring Steel Generated By High-Speed Water Quenching, Diego E. Lozano, George E. Totten, Yaneth Bedolla-Gil, Martha Guerrero-Mata, Marcel Carpio, Gabriela M. Martinez-Cazares

Mechanical and Materials Engineering Faculty Publications and Presentations

Automotive components manufacturers use the 5160 steel in leaf and coil springs. The industrial heat treatment process consists in austenitizing followed by the oil quenching and tempering process. Typically, compressive residual stresses are induced by shot peening on the surface of automotive springs to bestow compressive residual stresses that improve the fatigue resistance and increase the service life of the parts after heat treatment. In this work, a high-speed quenching was used to achieve compressive residual stresses on the surface of AISI/SAE 5160 steel samples by producing high thermal gradients and interrupting the cooling in order to generate a case-core …

Micron-Sized Spinel Crystals In High Level Waste Glass Compositions: Determination Of Crystal Size And Crystal Fraction, C. (Charmayne) E. Lonergan, K. Akinloye-Brown, J. Rice, V. Gervasio, N. Canfield, M. J. Schweiger, J. D. Vienna

Materials Science and Engineering Faculty Research & Creative Works

The compositions utilized for immobilization of high-level nuclear wastes (HLW) are controlled using glass property models to avoid the deleterious effects of crystallization in the high-level waste (HLW) vitrification melters. The type and size of the crystals that precipitate during melter operations (typically at 1150 °C) and idling (∼1000 °C) are significantly impacted by glass composition and thermal history. This study was conducted to measure the impact of melt composition and heat treatment temperature on crystal size and fraction. A matrix of 31 multi-component glasses canvasing the expected Hanford HLW compositional space was developed and the glasses fabricated, and heat …

Development Of Low Cost, Environmentally Friendly And High Strength Carbon Foams From Bread And Cake, Laura Mountain-Tuller

Materials Engineering

Carbon foam is a high niche material that consists of a highly porous, three-dimensional cellular network that is characterized by extremely high strength-to-weight ratios and low thermal conductivity. Due to these properties, carbon foams excel in structural and thermal applications, especially in the aerospace industry. Typically, carbon foams are formed through a heating process called pyrolysis of polymer precursors with high carbon content. This process is done at high temperatures in an oxygen free environment. These precursors are expensive to make and use toxic chemicals to produce, therefore, there is a push to find an environmentally friendly and cost-effective method …

In Situ Sem Solidification Study Of Ga And Egain: A Characterization Technique For Monitoring The Microstructural Evolution Of Liquid Metals, Jeremy Geovann Del Aguila

Materials Engineering

Scanning electron microscopy (SEM) video recording is used to characterize the solidification of small volumes of 99.999% pure gallium (Ga) and eutectic gallium-indium (eGaIn) under a high vacuum environment. Specimen are superheated to 55℃ using a hot plate, cast into spherical droplets, and cooled in situ by means of a Peltier cooling stage. Special attention is given to the preparation of the specimen prior to viewing because of gallium and its alloys’ nature to form an oxide layer when melted and air cooled. The oxide acts as a skin that inhibits the observation of microstructural features during solidification. Heated samples …

Comparative Study Of Cv3 Carbonaceous Chondrites Allende And Bali Using Micro-Raman Spectroscopy And Sem/Eds, Raka Paul

All Graduate Theses, Dissertations, and Other Capstone Projects

The birth of the solar system (over 4 billion years) is speculated to have happened from a nebula, swirling and compacting in localized regions to eventually form the Sun and planets. This complex process consists of numerous changes and intermediary steps, yet to be fully understood. Carbonaceous chondritic meteorites are relics of that process and therefore have potential to reveal information about the formation history. Several theories have been formulated linking their composition to planet formation. This study focusses on two carbonaceous chondritic specimens, Allende and Bali, both of the group CV and petrologic type 3. CV meteorites are abundant …

The Relationship Between Structural Parameters And Mechanical Properties Of Cactus Spines, Jorge Armando Martinez, Pamela Liz Szeto, Theresa Mae Stewart

Materials Engineering

Considering an increasing interest in renewable, biodegradable resources that exhibit excellent mechanical properties, 24 species of cactus spines were investigated using three-point bend testing, X-ray diffraction (XRD) for structural parameters, and scanning electron microscopy (SEM) to analyze fracture surfaces. Additionally, a density of about 1.3 g/cm3 was measured for each spine utilizing the displacement method, closely matching existing data from literature. The flexural modulus varied greatly between species, ranging from 1.22 GPa (Echinocactus polycephalus) to 43.58 GPa (Stenocereus thurberi). In addition, flexural strength and strain to failure was also measured for each spine. XRD analysis of …

Evaluation Of Strain Distortion Correction Protocol Using Scanning Electron Microscopy And Digital Image Correlation, Alexandra Mallory, Alberto Mello, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Scanning electron microscopy in combination with digital image correlation (SEM-DIC) is a useful technique for measuring strain in materials at the micro-scale. In particular, it can be used to identify micro-scale strain localizations that are the precursor to material failure. While SEM produces high resolution images of the microstructure, the images also contain a large amount of distortion that, during DIC, will result in distorted strain values that require correction. In this project, a nickel-based alloy underwent cyclic mechanical fatigue at three different high temperatures to a targeted maximum strain. Scanning electron microscopy imaging was done on a 200x150μm area …

Synthesis And Characterization Of Kesterite Cu2znsns4 (Czts) Thin Films For Solar Cell Application, Mohamed M.A. Abusnina

Electronic Theses and Dissertations

The quaternary compound Cu₂ZnSnS₄ (CZTS) gained considerable attention in the last decade due to its potential as an active-layer semiconductor for low-cost thin-film solar cells. The material is composed of nontoxic and Earth-abundant constituents, has optical properties suitable for photovoltaic application, and can be synthesized using a wide variety of methods.

Polycrystalline CZTS was grown in this work using vacuum-based deposition to first deposit metal films (precursors) of Cu, Zn, and Sn. In a subsequent step, the precursors underwent an annealing treatment in sulfur vapor environment (sulfurization) to form CZTS. Using sputtering, a physical vapor deposition (PVD) …

Application Of 3d Printing Technology In Porous Anode Fabrication For Enhanced Power Output Of Microbial Fuel Cells, Bin Bian

Electronic Thesis and Dissertation Repository

Microbial fuel cells (MFCs) are widely researched for application in wastewater treatment. However, the current anodes used in MFCs often suffer from high fabrication cost and uncontrollable pore sizes. In this thesis, three-dimensional printing technique was utilized to fabricate anodes with different micro pore sizes for MFCs. Copper coating and carbonization were applied to the printed polymer anodes to increase the conductivity and specific surface area. Voltages of MFCs with various anodes were measured as well as other electrochemical tests such as linear sweep voltammetry and electrochemical impedance spectroscopy. 3D copper porous anode produced higher maximum voltages and power densities …

An Evaluation Of Biofield Treatment On Thermal, Physical And Structural Properties Of Cadmium Powder, Mahendra Kumar Trivedi, Gopal Nayak, Shrikant Patil, Rama Mohan Tallapragada, Omprakash Latiyal, Snehasis Jana

Mahendra Kumar Trivedi

Characterization Of Physical And Structural Properties Of Brass Powder After Biofield Treatment, Mahendra Kumar Trivedi, Gopal Nayak, Rama Mohan Tallapragada, Omprakash Latiyal, Snehasis Jana

Mahendra Kumar Trivedi

Impact Of Biofield Treatment On Physical, Structural And Spectral Properties Of Antimony Sulfide, Mahendra Kumar Trivedi, Gopal Nayak, Shrikant Patil, Rama Mohan Tallapragada, Omprakash Latiyal

Mahendra Kumar Trivedi

Impact Of Symmetry On The Ferroelectric Properties Of Catio₃ Thin Films, Michael D. Biegalski, Liang Qiao, Yijia Gu, Apurva Mehta, Qian He, For Full List Of Authors, See Publisher's Website.

Materials Science and Engineering Faculty Research & Creative Works

Epitaxial strain is a powerful tool to induce functional properties such as ferroelectricity in thin films of materials that do not possess ferroelectricity in bulk form. In this work, a ferroelectric state was stabilized in thin films of the incipient ferroelectric, CaTiO₃, through the careful control of the biaxial strain state and TiO₆ octahedral rotations. Detailed structural characterization was carried out by synchrotron x-ray diffraction and scanning transmission electron microscopy. CaTiO₃ films grown on La_0.18Sr_0.82Al_0.59Ta_0.41O₃ (LSAT) and NdGaO₃ (NGO) substrates experienced a 1.1% biaxial strain state …

Determination Of Current Density Distribution In An Electron Beam, Yudhishthir Prasad Kandel

Legacy Theses & Dissertations (2009 - 2024)

Electron beams are useful in many applications because they can be focused down to a spot far exceeding the physical limit of focusing visible light or x-rays. Additionally, electron beams are useful in transferring concentrated amounts of energy to a very small well defined region of a target for a fixed duration. This has led to the development of both scanning electron microscopes (SEMs) and electron beam lithography. The goal of this work was to develop a general method that accurately and easily yields the best estimate of the electron current density distribution of a focused electron beam, known as …

Digital Image Correlation Of Heterogeneous Deformations In Polycrystalline Material With Electron Backscatter Diffraction, Javier Esquivel

Open Access Theses

This work establishes the ability to conduct digital image correlation (DIC) investigations at varying length scales. DIC allows for a computational method of strain field measurements using multiple images to track random speckle patterns on material surfaces. The use of a powder silicon oxide speckle allows for high optical magnification correlation using conventional load frames. Self-assembling gold nanoparticles provide sub-micron resolution speckle patterns to study microstructure influences on deformation using scanning electron microscopy. The complex microstructure in aerospace grade aluminum and nickel-based superalloys, give rise to varied deformation fields, which can be studied using electron backscatter diffraction. Specimen preparation techniques, …

Corrosion Resistance Of A Sand Particle-Modified Enamel Coating Applied To Smooth Steel Bars, Fujian Tang, Genda Chen, Richard K. Brow, Michael L. Koenigstein

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The protective performance of a sand particle-modified enamel coating on reinforcing steel bars was evaluated in 3.5 wt% NaCl solution by electrochemical impedance spectroscopy (EIS). Seven percentages of sand particles by weight were investigated: 0%, 5%, 10%, 20%, 30%, 50% and 70%. The phase composition of the enamel coating and sand particles were determined with the X-ray diffraction (XRD) technique. The surface and cross-sectional morphologies of the sand particle-modified enamel coating were characterized using scanning electron microscopy (SEM). XRD tests revealed three phases of sand particles: SiO₂, CaCO₃ and MgCO₃. SEM images demonstrated that the …

Freeze-Form Extrusion Fabrication Of Functionally Graded Material Composites Using Zirconium Carbide And Tungsten, Ang Li, Aaron S. Thornton, Bradley K. Deuser, Jeremy Lee Watts, Ming-Chuan Leu, Greg Hilmas, Robert G. Landers

Materials Science and Engineering Faculty Research & Creative Works

Ultra-high-temperature ceramics are being investigated for future use in aerospace applications due to their superior thermo-mechanical properties, as well as their oxidation resistance, at temperatures above 2000⁰C. However, their brittleness makes them susceptible to thermal shock failure. As graded composites, components fabricated as functionally-graded materials (FGMs) can combine the superior properties of ceramics with the toughness of an underlying refractory metal. This paper discusses the grading of two materials through the use of a Freeze-form Extrusion Fabrication (FEF) system to build FGM parts consisting of zirconium carbide (ZrC) and tungsten (W). Aqueous-based colloidal suspensions of ZrC and W were developed …

Measurement Of Semiconductor Surface Potential Using The Scanning Electron Microscope, Jennifer T. Heath, Chun-Sheng Jiang, Mowafak M. Al-Jassim

Faculty Publications

We calibrate the secondary electron signal from a standard scanning electron microscope to voltage, yielding an image of the surface or near-surface potential. Data on both atomically abrupt heterojunction GaInP/GaAs and diffused homojunction Si solar cell devices clearly show the expected variation in potential with position and applied bias, giving depletion widths and locating metallurgical junctions to an accuracy better than 10 nm. In some images, distortion near the p-n junction is observed, seemingly consistent with the effects of lateral electric fields (patch fields). Reducing the tube bias removes this distortion. This approach results in rapid and straightforward collection of …

Monotonic And Cyclic Compression Behavior Of Bulk Metallic Glasses, Matthew Webster Freels

Doctoral Dissertations

The cyclic-compression behavior of a Cu45Zr45Al5Ag5 bulk metallic glass (BMG) was investigated in order to elucidate the damage initiation and growth mechanisms. The present Cu45Zr45Al5Ag5 BMG was found to have the highest fatigue-endurance limit for BMGs reported to date. Fracture under cyclic compression occurred in a pure shear mode. In addition to many shear bands and cracks, areas of “chipping” were commonly found on the outside surfaces of the fatigue specimens. Crack growth rates were found decrease with cycles.

The effects of the as-cast specimen size, cooling rate, and the free volume content on the monotonic and cyclic compression behavior …

Tensile Properties Of Martensitic Stainless Steels At Elevated Temperatures, Ajit K. Roy, Srinivasarao R. Kukatla, Bhagath Yarlagadda, V. N. Potluri, Martin Lewis, Brendan O'Toole

Mechanical Engineering Faculty Research

Tensile properties of quenched and tempered martensitic alloys EP-823, HT-9, and 422 were evaluated at temperatures ranging from ambient to 600 °C as a function of three different tempering times. The results indicated that the yield strength, ultimate tensile strength, and the failure strength were gradually reduced with increasing temperature. The ductility parameters were enhanced at elevated temperatures due to increased plastic flow. However, the tempering time did not significantly influence these properties. The evaluation of the fracture surfaces by scanning electron microscopy revealed reduced cracking and dimpled microstructures, indicating enhanced ductility at higher testing temperatures.