Digital Commons Network^™

High Temperature Strength Reduces Soldering In Aluminum High Pressure Die Casting, Jacob A. Belke

Dissertations, Master's Theses and Master's Reports

Die soldering, an adhesion defect in high pressure die casting (HPDC), is a symptom of localized sticking where a localized portion of the cast material is adhered to the tooling surface causing build up over time. This requires the tooling to be serviced which incurs additional costs to the process that gets passed on to the parts. Historically, soldering has been mitigated using lubricants, coatings, and alloy chemistry modifications but solder persists.

The Tresca friction thermomechanical model suggests soldering occurs when the local interfacial shear stress between the casting and die surface exceeds the local shear strength of the casting. …

Characterization Of Residual Stress And Precipitate Evolution In Aluminum 2xxx Self-Reacting Friction Stir Welds, Benjamin Joe Wing

Doctoral Dissertations

2xxx series aluminum alloys possess attractive properties for structural aerospace applications including high strength to weight ratio, corrosion resistance, and stable cryogenic performance. Solid state joining processes are often employed to reduce weld defects and improve weld performance/consistency as many alloys of this range have poor weldability for traditional fusion based joining techniques. One such process, self-reacting friction stir welding (SRFSW) allows for consistent high-quality, welding of large and curved articles is often used in the construction of large structures such as launch vehicle liquid propellant tanks.

Despite the merits of this process, joint softening (a decrease in mechanical properties …

Effect Of Sc On Recrystallization Resistance Of Aa7050, Keaton Schmidt

Dissertations, Master's Theses and Master's Reports

The extrusion process involves high temperatures and strains that can result in undesirable microstructures, especially along the surface. Extruded alloys tend to exhibit surface recrystallization during heat treating at regions of higher strains, which can lead to reduced fatigue strength and corrosion resistance. By adding Sc to AA7050, nano-sized dispersoids are formed with Sc cores and Zr shells that restrict recrystallization more than the base alloy that only utilizes Zr. Billets with varying Sc content and a control with only Zr were cast, and extrusions were made in order to compare surface microstructures at varying strains in the as-extruded and …

Intergranular And Pitting Corrosion Mechanisms Of Sensitized Aluminum Alloy Aa5083, Clayton Egleston

Williams Honors College, Honors Research Projects

The motivation and objectives of this project is to examine the mechanisms of intergranular corrosion (IGC) and pitting corrosion of sensitized AA5083. In this regard, different characterization techniques were used, including optical analysis of microstructure, cyclic potentiodynamic polarization with Tafel fitting, electrochemical impedance spectroscopy with electrical equivalent circuit (EEC) fitting, and potentiostatic current transient monitoring. The transition from IGC to pitting corrosion occurs when the grain boundaries become saturated with the β-phase (Mg₂Al₃). It was found that AA5083 becomes more vulnerable to pitting corrosion as the degree of sensitization increases.

Non-Destructive Material Analysis Of Metals And Composites Via Thermography, Jonathan R. Doubt, James L. Chapman

Materials Engineering

The Naval Surface Warfare Center, Port Hueneme Division, is interested in the development of non-destructive damage assessment of shipboard materials via drones at distance. Long Pulsed Thermography (LPT), a method of non-destructive evaluation, was investigated as a possible method for detecting damage in metals (5005h24 Al alloy and 1008 carbon steel) and composites (aramid fiber honeycomb sandwich structure) at distances from 0.5 m to 3.0 m. LPT was conducted using two 1000 W can lights to heat the samples, and a FLIR E8-XT thermal camera. The images were then analyzed using ImageJ software to determine if damage could be detected …

Feedstock Powders For Reactive Structural Materials, Daniel Hastings

Dissertations

Metals as fuels have higher energy density per unit mass or volume compared to any hydrocarbon. At the same time, metals are common structural materials. Exploring metals as reactive structural materials may combine their high energy density with attractive mechanical properties. Preparing such materials, however, is challenging. Requirements that need to be met for applications include density, strength, and stability enabling the component to sustain the structure during its desired operation; added requirements are the amount and rate of the energy release upon impact or shock. Powder technology and additive manufacturing are approaches considered for design of reactive structural materials. …

Strengthening Of 7175 Aluminum Alloy Through Multi-Step Aging Process, Colin E. Masterson, Ryland W. Jolliffe

Materials Engineering

7175 is a heat-treatable aluminum alloy commonly used in aerospace forgings. This alloy is aged with a multi-step heat treatment. This treatment must balance strength with stress corrosion cracking resistance through a degree of overaging. The team was tasked by Weber Metals to increase the strength of this treatment without sacrificing stress corrosion cracking resistance. Both two-step and retrogression and reaging treatments were tested in experiments to find a heat treatment that could increase the yield and tensile strength by 1-2 ksi while maintaining a minimum electrochemical conductivity equivalence of 38% relative to copper. Two-step aging is the more conventional …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

Analyzing Variation In Dispersoid Formation In Aluminum Alloys By Minor Changes In Homogenization Temperature, Brendan Treanore

Dissertations, Master's Theses and Master's Reports

The homogenization of billets in the aluminum extrusion industry is a critical step that removes chemical segregation from casting, dissolves low melting point phases, forms nanoscale dispersoid phases, and promotes the beta to alpha transformation of iron particles in the matrix. With ever increasing use of aluminum extrusion in the automotive industry there is a constant need for increased efficiency and consistency in processing of extruded aluminum. The work in this thesis explores the effects of 10°C differences in the homogenization temperature on the formation of dispersoids in 6082 alloys used in the automotive industry. The role of dispersoids is …

Atmospheric Corrosion Of Galvanically Coupled Aluminum Alloys And Carbon Steel, Mitchell Felde

Williams Honors College, Honors Research Projects

Aluminum alloys are a steadily growing material being commonly used in lieu of typical steels. Additional alloying, heat treatment, and other property enhancing processes are expanding the use of these alloys. However, with this expansion, galvanic corrosion is becoming more of an issue in the design stage due to the combination of these alloys with steels. The automotive industry is one industry where the use of aluminum alloys is becoming common practice. Aluminum alloys provide a lightweight aspect over the conventional carbon steel that was used previously. As a result of this transition towards more lightweight materials, galvanic coupling is …

Development Of A Novel Casting Alloy Composed Of Aluminum And Cerium With Other Minor Additions, Zachary Cole Sims

Doctoral Dissertations

Eutectic casting alloys of aluminum and cerium are a recent discovery and early research describes an alloy with great potential to meet the growing demand for a lightweight, economical, high specific strength material for use in high-temperature or extremely corrosive environments. The broad application of aluminum alloys across industry sectors is driven by their collection of balanced properties including economical cost, high specific strength, and flexibility of their production pathways. Additionally, their high corrosion resistance makes them a good choice for structural materials. Despite this, the push to use aluminum alloys in ever more extreme environments with higher temperatures, stresses, …

Boron Nitride Nanotube Based Lightweight Metal Matrix Composites: Microstructure Engineering And Stress-Transfer Mechanics, Pranjal Nautiyal

FIU Electronic Theses and Dissertations

Lightweight metals, such as Aluminum, Magnesium and Titanium, are receiving widespread attention for manufacturing agile structures. However, the mechanical strength of these metals and their alloys fall short of structural steels, curtailing their applicability in engineering applications where superior load-bearing ability is required. There is a need to effectively augment the deformation- and failure-resistance of these metals without compromising their density advantage.

This dissertation explores the mechanical reinforcement of the aforementioned lightweight metal matrices by utilizing Boron Nitride Nanotube (BNNT), a 1D nanomaterial with extraordinary mechanical properties. The nanotubes are found to resist thermo-oxidative transformations up to ~750°C, establishing their …

Comparison Of Aluminum And Manganum Concentration In Akmola Region, Kazakhstan, A. G. Zhumalina, E. K. Sambayev, A. Sakaguchi, S. Endo, K. Tanaka, T. Kajimoto, N. Kawano, T. B. Suleimenov, K. Sh. Zhumadilov, M. Hoshi

Eurasian Journal of Physics and Functional Materials

The results of seasonal Al and Mn activity on the surface of the atmosphere above the city of Nur-Sultan are shown from October 2016 to January 2017. The technique of sampling aerosols in various fractions and further analysis of the data are described. Together with scientists from the University of Hiroshima (Hiroshima, Japan) and the University of Tsukuba (Tsukuba, Japan), the composition of aerosols in the air of Astana was monitored. The aim of the project was to develop a methodology for sampling aerosols in various fractions and conduct measurements on an ongoing basis. The studies were carried out using …

Galvanic Corrosion In Aluminum/Steel Joints, Maegan Saul

Williams Honors College, Honors Research Projects

As car manufacturers seek to use lighter weight materials, aluminum is being more commonly used in the construction of vehicles. However, the strength of steel cannot be matched and both metals are necessary, leading to the joining of dissimilar metals. This connection of different metals leads to a galvanic coupling and subsequent corrosion of the less noble metal. This project aims to observe the corrosion and galvanic coupling behavior of aluminum alloys and carbon steel so that a model may be produced which can accurately predict the expected responses of the metals in various environments. Better, more accurate modeling of …

Benefits Of Aluminum: Comparing The Common Materials In The Bar Grating Industry, Joanthan Geiser

Williams Honors College, Honors Research Projects

The main aim of this project is to study the wholistic behavior of the 6xxx series of aluminum for use in the bar grating industry for a waste water treatment environment. This project will study the comparison of certain aluminum 6xxx series alloys to steel, stainless steel, and glass fiber-reinforced plastic. While comparing these materials, it will look at the mechanical properties such as modulus of elasticity, yield strength, and ultimate tensile strength. In addition, the available corrosion test of the 6xxx series aluminum alloys will be examined to find a generalization of the corrosion behavior for this series. A …

In Silico Analysis Of Advanced Processing Methods For Light-Weight Alloys Powders, Marjan Nezafati

Theses and Dissertations

Light-weight Al and Mg-based metal-matrix nanocomposites (MMNCs) are lauded as one of the most promising structural materials for vehicle, military, and construction applications. These MMNCs are often synthesized using the powder metallurgy (PM) process under liquid nitrogen cryogenic environments to control the grain sizes. It is believed that proper incorporation of the nitrogen species into the bulk lattice during processing could strongly enhance the mechanical properties of MMNCs by forming N-rich dispersoids. In this work, using the density-functional theory (DFT), the adsorption, absorption and diffusion behavior of nitrogen molecule/atoms have been studied and related to t Al and Mg MMNC …

Effect Of Zr Additions On Thermal Stability Of Al-Cu Precipitates In As-Cast And Cold Worked Samples, Kyle Deane, Paul G. Sanders

Michigan Tech Publications

While Zr is frequently added to Al alloys to control grain size with the formation of large (>1 μm) primary precipitates, little research has been conducted on the effect of nanoscale Al₃Zr precipitates on Al alloys. By comparing the precipitation and corresponding strength evolution between Al-Cu-Zr alloys with different Zr concentrations, the effects of Zr on Al-Cu precipitation with and without primary Al₃Zr precipitates can be observed. In the absence of these large precipitates, all Al₃Zr phases can be formed, through high temperature aging treatments, as a dispersion of nanoprecipaites inside the Al …

Scalable Patterning Using Laser-Induced Shock Waves, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Claire Ottman, Dylan Sanford, Zachary Thomas, Omer San, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and minimal environmental impact to create a thermally controllable surface pattern using the laser pulses is reported. Patterned microindents were generated on Ni₅₀Ti₅₀ shape memory alloys and aluminum using an Nd: YAG laser operating at 1064 nm combined with a suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities, which generate pressure pulses up to a few GPa on the surface, were focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto …

Evaluation Of Metallurgical And Mechanical Properties Of Alsi10mg Produced By Selective Laser Melting, Luke J. Suttey

Graduate Theses & Non-Theses

Selective laser melting (SLM) additive manufacturing (AM) of metal powders has long been a focus in the study of AM due to the possibility of weight reduction, complex shape formation, and production cost savings. Although applicable to a variety of metals SLM AM of the AlSi10Mg alloy was studied in an attempt to characterize the effect of processing parameter and build angle variation on the final microstructural, fractographic, and mechanical properties of parts produced without any thermal post-processing techniques. Research was conducted on five build angles (0°, 30°, 45°, 60°, and 90°), and three Global Energy Densities (GED) (37.15, 45.39, …

Understanding Homogeneous Nucleation In Solidification Of Aluminum By Molecular Dynamics Simulations, A. Mahata, Mohsen Asle Zaeem, M. I. Baskes

Materials Science and Engineering Faculty Research & Creative Works

Homogeneous nucleation from aluminum (Al) melt was investigated by million-atom molecular dynamics simulations utilizing the second nearest neighbor modified embedded atom method potentials. The natural spontaneous homogenous nucleation from the Al melt was produced without any influence of pressure, free surface effects and impurities. Initially isothermal crystal nucleation from undercooled melt was studied at different constant temperatures, and later superheated Al melt was quenched with different cooling rates. The crystal structure of nuclei, critical nucleus size, critical temperature for homogenous nucleation, induction time, and nucleation rate were determined. The quenching simulations clearly revealed three temperature regimes: sub-critical nucleation, super-critical nucleation, …

Superhydrophobic Surface On Aluminum Alloy By Hydrothermal Method And Its Electrochemical Performance, Xiao-Hang Chen, Mo-Jing Chen, Yu-Lin Min, Qun-Jie Xu

Journal of Electrochemistry

Superhydrophobic film formed on a metal surface is an effective way for corrosion protection. In this paper, the superhydrophobic film was prepared on the surfaces of aluminum alloy by hydrothermally treating with a solution containing CeCl₃·7H₂O and CO(NH₂)₂ , and a self-assemble process. The electrochemical measurements and surface morphology results confirmed that the best superhydrophobicity and electrochemical performance could be achieved with the contact angle of 155.5^o after six hours of hydrothermal reaction. Furthermore, the inhibition efficiency of 99.6% was obtained in 3.5 wt% NaCl aqueous solution, indicating the excellent corrosion resistance …

Effect Of Ultrasonic Treatment On The Microstructure And Mechanical Properties Of Al6061 And Composite, Ana S. Exime

FIU Electronic Theses and Dissertations

In this study, the effect of ultrasonic treatment (UST) parameters such as amplitude, sonication time, and melt temperature on microstructure and microhardness of Al 6061 alloy is evaluated. The effect of UST on the dispersion of tungsten disulfide (WS₂) and carbon nanotubes (CNT) as reinforcement particles in Al 6061 during casting is also studied. The cast Al 6061 with UST demonstrated 32% grain size reduction and 8% increase in the microhardness for optimum processing conditions. The cavitation process induced by UST is responsible for the refinement in microstructure and increase of hardness by enhancing the degassing and nucleation …

Aluminum Matrix Syntactic Foam Fabricated With Additive Manufacturing, M. Spratt, Joseph William Newkirk, K. Chandrashekhara

Materials Science and Engineering Faculty Research & Creative Works

Syntactic foams are lightweight structural composites with hollow reinforcing particles embedded in a soft matrix. These materials have applications in transportation, packaging, and armor due to properties such as relatively high specific stiffness, acoustic dampening, and impact absorption. Aluminum matrices are the most widely studied of metal matrix syntactic foams, but there is little to no research in regards to processing the foams with additive manufacturing. It is theorized that the fast cooling rates and limited kinetic energy input of additive could reduce two issues commonly associated with processing syntactic foams: microsphere flotation in the melt and microsphere fracture during …

The Effects Of Carboxylic Acids In Aluminum Anodizing, Abby E. Koczera

Honors Theses and Capstones

Hard-anodized alumina coatings were formed in sulfuric acid at low temperature and high current density in the presence of carboxylic acid additives. Citric acid, trimesic acid, mellitic acid and ethylenediaminetetraacetic acid (EDTA) were utilized in varying concentrations. The additives were chosen for their capacity to form complexes with tri-valent aluminum and hence impart chemical stability to the coatings. The coatings were sealed in boiling water, and corrosion resistance was observed in a high pH solution of potassium hydroxide. The coatings were examined using scanning electron microscopy (SEM) to assess coating thickness and pore dimensions. Thicker coatings were produced when the …

Corrosion Of Aluminum Current Collector In Cost Effective Rechargeable Lithium-Ion Batteries, Shengyi Li

Theses and Dissertations

Rechargeable lithium ion batteries (LIB) have been widely used as commercial energy storage systems for portable equipment, electronic devices and high power applications (e.g. electronic vehicles). One issue with the commercialized LIB is that expensive, highly toxic and flammable organic solvents are used in the electrolyte and the fabrication process of electrodes. The toxic organic based solvents increase the production cost and lead to significant safety concerns in the event of a battery overcharge or short circuit. The recent development of “green manufacturing” technology allows manufacturers to replace the organic solvents used in the cathode coating process by aqueous based …

Modelling The Evaporation Of Aluminum In Ti–6al–4v Alloy Melted With Electron Beam And Laser, Xuan Wang, Liang Wang, Liang S. Luo, Yan Q. Su, Xin Z. Li, Rui R. Chen, Jing J. Guo, Heng Z. Fu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Thermodynamic Simulation For Solidification Path In Die Casting Alloy Development, Mohamad Rusydi Mohamad Yasin, Dongke Sun, Qingyou Han

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Slm Processing-Microstructure-Mechanical Property Correlation In An Aluminum Alloy Produced By Additive Manufacturing, Bryce Abstetar

Graduate Theses & Non-Theses

Additive manufacturing has become a highly researched topic in recent years all over the world. The current research evaluates the merits of additive manufacturing based on the mechanical, microstructural, and fracture properties of additive manufactured AlSi10Mg test specimens. The additive manufactured build plates consisted of tensile and fatigue test specimens. They were printed in the 0°, 30°, 60°, and 90° orientations relative to the build platform. Tensile and dynamic fatigue tests were conducted followed by microstructural characterization and fracture analysis. A wrought 6061 T6 aluminum alloy was also tested for comparison. Tensile tests revealed similar ultimate tensile strengths for all …

Characterization Of Superabsorbent Polymers In Aluminum Solutions, Nicholas D. Macke, Matthew J. Krafcik, Kendra A. Erk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Over the past few decades, super absorbent polymers (SAPs) have been the topic of research projects all around the world due to their incredible ability to absorb water. They have applications in everything from disposable diapers to high performance concrete. In concrete, aqueous cations permeate the polymer network, reducing swelling and altering properties. One of these ions, aluminum, alters SAP properties by creating a stiff outer shell and greatly reducing absorbency, but these effects have not been well characterized. One method of characterizing the effects of aluminum on SAP hydrogels was performing gravimetric swelling tests to determine equilibrium water capacity …

Effect Of Thermal Exposure On Tensile Strength And Microhardness Of Welded And Precipitation Hardened Rx82 Aluminum Alloy Extrusions In The T4 And T6 Conditions, Lucien Miller

Materials Engineering

This investigation is focused on the effect paint-bake cycles have on the tensile strength and microhardness of GMAW welded RX82 aluminum extrusions in T4 and T6 base conditions. To simulate the paint-bake cycle, T4 and T6 RX82 aluminum samples were GMAW welded and heat treated at 350°F, 390°F, and 425°F for durations of 30 minutes, 1.0 hour, and 2.0 hours, with five replicates for each treatment. Microhardness profiles of T4 samples treated at 350°F for 30 minutes and 1.0 hour display weld/HAZ HV values of 86.04 and 82.51 respectively, followed by maximums of 123.21 and 121.10. Average ultimate tensile strength …