Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Entire DC Network
The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels
The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels
Electronic Theses and Dissertations
The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).
Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …
Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates
Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates
Electronic Theses and Dissertations
As the interest and implementation of renewable energy accelerates, so does that of grid energy storage. It is widely believed that a cost-effective energy storage technology will bring about the proliferation of renewable energy. Redox flow battery (RFB) technology represents a promising solution to cost-effective grid energy storage. Compared to other technologies, RFBs have a long lifetime, high efficiency, are non-flammable, significantly reduce cost, and separately scale power and energy. The separation of power and energy enables increased energy capacity by simply adding electrolyte volume. Of the challenges facing RFB technology, one readily apparent is the cost of the active …
Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath
Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath
Electronic Theses and Dissertations
Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …
Rare Earth Oxide Coating With Controlled Chemistry Using Thermal Spray, Virendra Singh
Rare Earth Oxide Coating With Controlled Chemistry Using Thermal Spray, Virendra Singh
Electronic Theses and Dissertations
Cerium oxide (Ceria) at nano scale has gained significant attention due to its numerous technological applications. Ceria in both doped and undoped forms are being explored as oxygen sensor, catalysis, protective coating against UV and corrosion, solid oxide fuel cell (SOFC) electrolyte and newly discovered antioxidant for biomedical applications. Therefore, there is an imminent need of a technology which can provide a cost effective, large scale manufacturing of nanoceria and its subsequent consolidation, specially using thermal spray. This dissertation aims to develop a scientific understanding towards the development of pure and doped ceria- based coating for a variety of technological …
Polymer-Derived Si-Al-C-N Ceramics:Oxidation, Hot-Corrosion, And Structural Evolution, Yiguang Wang
Polymer-Derived Si-Al-C-N Ceramics:Oxidation, Hot-Corrosion, And Structural Evolution, Yiguang Wang
Electronic Theses and Dissertations
Polymer-derived ceramics are a new class of materials synthesized by thermal decomposition of polymer precursors. Previous studies have shown that the materials exhibit excellent thermo-mechanical properties and can be stable at temperatures up to 2000oC. Furthermore, the novel polymer-to-ceramics process enables the manipulation of the ceramic structures at the atomic/nano level by designing the chemistry of polymer precursors and controlling the pyrolysis conditions, thereby, the properties of ceramics. In this dissertation, oxidation/hot-corrosion behavior and the structural evolution of Si-Al-C-N ceramics have been studied. The structural evolution and crystallization behavior of the SiCN and SiAlCN ceramics are investigated using FT-IR, XRD, …