Digital Commons Network^™

Fabrication Of Solar Absorber Tube With Internal Fin Structure With In718 And Effect Of Boron With In718 For Solar Absorber Tube Using Selective Laser Melting 3d Printing Technology, Naznin Nuria Afrin

Theses and Dissertations

This research aimed to fabricate Solar Absorber Tubes for Solar-Thermal Power Plant with internal fin structures using Selective Laser Melting (SLM) technology. In this study, we investigated the effect of B with IN718 in 3D printing using SLM for solar absorber tubes. The objective was to study the material-process-properties relationship with goal to identify and validate the optimal parameters for the SLM process. Material selected for this study was IN718 with 0.5% and 1% B particle mixed using a V-shape mixing machine. The flowability test was conducted using the Angle of Repose (AOR) method. 3D printed samples …

The Deflection And Heat Transfer Analysis Of Injection Mold Cavity With Sla Cooling Channel Insert, Olumide Temidayo Aladesiun

Theses and Dissertations

Fast cooling in injection molding is the critical in the process economy. Among many different cooling channel designs available, conformal cooling offers the best and the most efficient cooling. However, limited awareness, accessibility, complexity, cost, knowledge, and experience limit the use of conformal cooling channels to be used into the mold in a molding process.

Typically, SLM(Selective Laser Melting) method is used to create cavity inserts with conformal cooling channels, however, due to the difficulties listed above, applications of conformal cooling channels are very limited. For an inexpensive alternative SLA (Stereolithography Apparatus) can print cavity inserts with conformal cooling channels. …

Ultrafast Laser Direct Writing Of Conductive Patterns On Modified Polyimide Film For Flexible Electronic Applications, Ishrat Jahan Biswas

Theses and Dissertations

Conductive patterns can be printed on a flexible polymer substrate using the direct laser writing (DLW) method. In order to write conductive circuits in such polymer using a laser, polyimide (PI) is a desirable material choice due to its electrical, chemical, and mechanical properties. Electrically non-conductive PI has shown great potential for flexible printed electronics as LDW enables selective carbonization in the bulk of such material leading to the formation of conductive lines. The technique is shown to be a rapid and minimal cost method for printing electrodes to nanoscale devices. However, investigations in this field show several limitations to …

A Study Of The Surface Properties Of Additive Manufactured Inconel 718 After Laser Surface Treatment And Cnc Grinding, Sampson K. Canacoo

Theses and Dissertations

This study investigated the surface properties of additive manufactured Inconel 718 produced through selective laser melting, and the effects of laser ablation and CNC grinding on the surface finish. The objectives were to investigate the effects of the various parameters of laser ablation and CNC grinding on the Inconel 718 surface. The parameters used for the laser experiments were pulse energy (4, 20, and 30 µJ), scanning speed (5, 10, and 15 mm/s), and hatch distance (10, 30, and 50 µm). For the grinding experiments, the wheel speed was kept constant at 20.3 m/sec, however, two different workpiece speed (8.6 …

A Numerical Simulation Of The Powder Bed Additive Manufacturing Process With Molecular Dynamics Simulation, Yeasir Mohammad Akib

Theses and Dissertations

Many manufacturing industries utilize powder bed fusion (PBF) since it can produce microscale precision 3D parts. During PBF, powder particles are selectively fused layer by layer using thermal energy. The build quality in the PBF process relies heavily on powder bed properties and thermal energy deposition. Powder flowability, spreadability, and packing fraction are some of the insightful factors that determine the quality of the powder bed. In this study, a two-dimensional powder bed is developed using the LAMMPS package. A cloud-based pouring of powders with varying volumes and initialization is adopted for the work. A blade-type and circular recoater is …

Investigation Of Process Parameters To Fabricate Refractory Medium-Entropy Alloy By Selective Laser Melting Process, Abdullah Al Masum Jabir

Theses and Dissertations

This thesis proposal investigates the synthesis of TiWMo refractory medium entropy alloy (RMEA) by selective laser melting process from elemental powder. Steel, titanium and tungsten substrates were used to study the impact on the formation of TiWMo RMEA. Different process parameters were applied to investigate the effects on melting, diffusion and formation of RMEA. The microstructure of TiWMo and elemental distribution were observed by scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS). SEM analysis revealed that with higher energy density the pores and microcracks were improved. EDS data validated the composition is homogenized and stable after few layers …

Femtosecond Pulse Filamentation In Dielectric Media Toward Photonics Sensor Fabrication, Anitha Narayanan

Theses and Dissertations

Through pulse filamentation, femtosecond laser pulses have been utilized to modify the refractive indices of dielectric materials such as glass, A-plane sapphire crystal, and Cplane sapphire crystal. The 10x Infinity Corrected Lens was used, and the focusing condition was tuned as being the same and fixed to both glass and sapphire crystals. First, 8uJ of laser energy was optimized to produce controlled pulse filamentation voids in the glass. The laser intensity was then optimized to 2-3.5 uJ, 1.5 uJ, & 2.5 uJ, respectively, for the controlled pulse filamentation in A and C plane sapphire crystals. Due to the different crystal …

Feasibility Analysis Of Embedding Optical Fiber Sensor Into Additively Manufactured Part, Mahmudul Hasan Porag

Theses and Dissertations

The research tried to examine the viability of the embedment of optical fiber sensors in Additively built components, packaging the sensors within the components, and characterizing the sensors for sensing a specified measurement. Optical fiber sensors are popular due to their small size, resilience against electromagnetic radiation, and reliability in potentially dangerous conditions. Embedding fibers inside a product allows for the monitoring of critical areas, allowing for preemptive action in the case of a breakdown. Coupons of Inconel 718 were made using laser powder-bed fusion (LPBF), with the fabrication settings tuned to determine whether such a development was possible. After …

Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin

Theses and Dissertations

This research considered additive manufactured (AM) molybdenum (Mo) and the effect of three variables on microstructure, mechanical properties, and the relationship between the two. Test temperature, laser speed, and shield gas or build atmosphere were varied, and samples tested and analyzed using a three-point bending test, chemical composition, and optical and scanning electron microscopy. The relationship among variables and results using a Design of Experiments was limited compared to the inclusion of every tested sample. Most effects were expected: samples tested at room temperature were brittle without statistical significance; increasing laser speed resulted in decreased ductility and strain, smaller grain …

Disruptions In International Trade: A Perspective On Ports Of Entry And Supply Chain Resilience, Jose A. Jara Jr. Guerrero

Theses and Dissertations

United States (U.S.) ports of entry (POEs) and supply chains (SCs) have a prominent trade relationship with a growing desire to improve their operational capabilities. Though trade deals like the U.S.-Mexico-Canada (USMCA) agreement have facilitated trade between these countries, U.S. Customs and Border Protection (CBP) at POEs have also increased security inspections, following the September 11th incident, which have impacted international and global SCs. More recently, the COVID-19 pandemic has caused labor shortages at both sea and land POEs, increasing vessel and commercial vehicle congestion. These POE disruptions have also propagated into the third-party logistics (3PL) of SC networks, which …

Monitoring Of Tool Wear And Surface Roughness Using Anfis Method During Cnc Turning Of Cfrp Composite, Md Mofakkirul Islam

Theses and Dissertations

Carbon fiber-reinforced plastic (CFRP) is gaining wide acceptance in areas including sports, aerospace and automobile industry . Because of its superior mechanical qualities and lower weight than metals, it needs effective and efficient machining methods. In this study, the relationship between the cutting parameters (Speed, Feed, Depth of Cut) and response parameters (Vibration, Surface Finish, Cutting Force and Tool Wear) are investigated for CFRP composite. For machining of CFRP, CNC turning operation with coated carbide tool is used. An ANFIS model with two MISO system has been developed to predict the tool wear and surface finish. Speed, feed, depth of …

Machine Learning Tools In The Predictive Analysis Of Ercot Load Demand Data, Md Riyad Hossain

Theses and Dissertations

The electric load industry has seen a significant transformation over the last few decades, culminating in the establishment and implementation of electricity markets. This transition separates electric generation services into a distinct, more competitive sector of the industry, allowing for the introduction of greater unpredictability into the system. Forecasting power system load has developed into a core research area in power and energy demand engineering in order to maintain a constant balance between electricity supply and demand. The purpose of this thesis dissertation is to reduce power system uncertainty by improving forecasting accuracy through the use of sophisticated machine …

Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya

Theses and Dissertations

The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …

Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen

Theses and Dissertations

Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …

Multi-Objective Optimization On Dimensional Accuracy, Edge And Surface Quality Of 3d-Printed Parts By Fused Deposition Modelling, Islam Hamdy Salem

Theses and Dissertations

Fused Deposition Modelling (FDM) is one of most common additive manufacturing (AM) techniques used in manufacturing field. It has been increasingly used because of its low cost and simplicity. Although FDM can save time through eliminating pre-processing tooling-up to produce the end-user product, still a better final product quality, like mechanical properties, dimensional accuracy and surface finish, is needed. This thesis addresses the maximization of involved printing parameters in one reliable model. Hence, a wider investigation is conducted in this research via experimental work in order to obtain a comprehensive model that involves and relates more parameters in a single …

Effects Of Additive Manufacturing Techniques On The Magnetocaloric Properties And Chemical Stability Of Lafexcoysi13-X-Y Alloys, Binyam Wodajo

Theses and Dissertations

Additive manufacturing (AM) is an emerging process to fabricate net shape, intricate, engineering components with minimal material waste; however, traditionally it has been largely applied to structural materials. AM of functional materials, such as magnetic materials, has received much less attention and the field is still in its infancy. To date, AM of magnetocaloric regenerators for magnetic refrigeration (an energy-efficient alternative to the conventional vapor-compression cooling technology), remains a challenge. There are several magnetic refrigerator device designs in existence today that are predicted to be highly energy-efficient, on condition that suitable working materials can be developed. This challenge in manufacturing …