Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 8 of 8
Full-Text Articles in Entire DC Network
Exploring Methods For Recycling Filament Waste In 3d Printing, Max Rios Carballo
Exploring Methods For Recycling Filament Waste In 3d Printing, Max Rios Carballo
Publications and Research
The goal of the current study is to investigate cutting-edge techniques for recycling filament waste from 3D printing procedures. Appropriate waste management techniques are required to reduce this trash's harmful environmental consequences. The goal of the project is to look at new methods for recycling filament waste in order to minimize disposal and encourage reuse. To acquire data from pertinent papers and research, a thorough literature review methodology was used. The findings show that this issue may be resolved utilizing a variety of recycling techniques, including shredding, melting, and re-extrusion. The type of filament waste and the intended goal will …
Waste Plastic Direct Extrusion Hangprinter, Aliaksei Petsiuk, Bharath Lavu, Rachel Dick, Joshua M. Pearce
Waste Plastic Direct Extrusion Hangprinter, Aliaksei Petsiuk, Bharath Lavu, Rachel Dick, Joshua M. Pearce
Michigan Tech Publications
As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel, open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression-screw-based end-effector that allows for the direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste …
Mechanical Characterizations Of 3d-Printed Plla/Steel Particle Composites, Hozhabr Mozafari, Pengfei Dong, Haitham Hadidi, Michael P. Sealy, Linxia Gu
Mechanical Characterizations Of 3d-Printed Plla/Steel Particle Composites, Hozhabr Mozafari, Pengfei Dong, Haitham Hadidi, Michael P. Sealy, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
The objective of this study is to characterize the micromechanical properties of poly-L-lactic acid (PLLA) composites reinforced by grade 420 stainless steel (SS) particles with a specific focus on the interphase properties. The specimens were manufactured using 3D printing techniques due to its many benefits, including high accuracy, cost effectiveness and customized geometry. The adopted fused filament fabrication resulted in a thin interphase layer with an average thickness of 3 μm. The mechanical properties of each phase, as well as the interphase, were characterized by nanoindentation tests. The effect of matrix degradation, i.e., imperfect bonding, on the elastic modulus of …
3d Printing Of Hybrid Mos2-Graphene Aerogels As Highly Porous Electrode Materials For Sodium Ion Battery Anodes, Emery Brown, Pengli Yan, Halil Tekik, Ayyappan Elangovan, Jian Wang, Dong Lin, Jun Li
3d Printing Of Hybrid Mos2-Graphene Aerogels As Highly Porous Electrode Materials For Sodium Ion Battery Anodes, Emery Brown, Pengli Yan, Halil Tekik, Ayyappan Elangovan, Jian Wang, Dong Lin, Jun Li
Department of Mechanical and Materials Engineering: Faculty Publications
This study reports a 3D freeze-printing method that integrates inkjet printing and freeze casting to control both the microstructure and macroporosity via formation of ice microcrystals during printing. A viscous aqueous ink consisting of a molecular MoS2 precursor (ammonium thiomolybdate) mixed with graphene oxide (GO) nanosheets is used in the printing process. Post-treatments by freeze-drying and reductive thermal annealing convert the printed intermediate mixture into a hybrid structure consisting of MoS2 nanoparticles anchored on the surface of 2D rGO nanosheets in a macroporous framework, which is fully characterized with FESEM, TEM, XRD, Raman spectroscopy and TGA. The resulting …
Environmental Impacts Of Selective Laser Melting: Do Printer, Powder, Or Power Dominate?, Jeremy Faludi, Martin Baumers, Ian Maskery, Richard Hague
Environmental Impacts Of Selective Laser Melting: Do Printer, Powder, Or Power Dominate?, Jeremy Faludi, Martin Baumers, Ian Maskery, Richard Hague
Dartmouth Scholarship
This life cycle assessment measured environmental impacts of selective laser melting, to determine where most impacts arise: machine and supporting hardware; aluminum powder material used; or electricity used to print. Machine impacts and aluminum powder impacts were calculated by generating life cycle inventories of materials and processing; electricity use was measured by in‐line power meter; transport and disposal were also assessed. Impacts were calculated as energy use (megajoules; MJ), ReCiPe Europe Midpoint H, and ReCiPe Europe Endpoint H/A. Previous research has shown that the efficiency of additive manufacturing depends on machine operation patterns; thus, scenarios were demarcated through notation listing …
Bioink Properties Before, During And After 3d Bioprinting, Katja Hölzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Bioink Properties Before, During And After 3d Bioprinting, Katja Hölzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Department of Mechanical and Materials Engineering: Faculty Publications
Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …
Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Department of Mechanical and Materials Engineering: Faculty Publications
Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
STAR Program Research Presentations
Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …