Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 15 of 15
Full-Text Articles in Entire DC Network
Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu
Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu
Graduate Theses and Dissertations
CMOS technology becomes important in Radio Frequency (RF) communication systems which include both a receiver and a transmitter. In a high performance radio receiver, the Low Noise Amplifier (LNA) is the first circuit, and its noise performance dominates the entire receiver. Depending upon the system in which they are used, LNAs can be designed according to various topologies and structures. The LNA needs to have matched input impedance, and at the same time it should amplify the small amplitude input signal without adding too much noise and still have the minimal power consumption. It also needs a good interface with …
Bankfull Geomorphic Relationships And Reference Reach Assessment Of The Ridge And Valley Physiographic Province Of East Tennessee, James Brady Mcpherson
Bankfull Geomorphic Relationships And Reference Reach Assessment Of The Ridge And Valley Physiographic Province Of East Tennessee, James Brady Mcpherson
Masters Theses
Waterways have been geomorphically altered or disturbed by development, mining, agriculture and other human activities for many years. Section 404 of the Clean Water Act determined that these impacts to our waterways must be mitigated for channel alterations. Stream restoration has been one method to mitigate for these impacts to our water resources. Stream restoration is considered to be a measurable improvement to the channel stability, water quality, habitat or overall function of a degraded stream system. Practices of stream restoration have changed in the last 10 to 20 years with the introduction of natural channel design methods. Natural channel …
Design And Testing Of An Automated Semiâ]Trailer Control System, Conor H. Dodd
Design And Testing Of An Automated Semiâ]Trailer Control System, Conor H. Dodd
Honors Theses
Growing up in Maine, the trucking industry is an ever-present part of life. With a very sparse, lightly used rail system, almost all of the raw materials and goods that enter and leave the state do so by truck. Truckers in Maine are constantly challenged by Maine’s roads, which can often be difficult or even treacherous to navigate. The rough logging roads near Jackman or Millinocket, or the sharp ninety degree turns near the Portland oil docks, can ruin a trucker’s day, or even worse, cause an accident. For example, there is a tiny four-way intersection on Broadway in South …
Design And Fabrication Of An Autonomous Solar Powered Airship, Mitchell Van Lee
Design And Fabrication Of An Autonomous Solar Powered Airship, Mitchell Van Lee
Honors Theses
The purpose of the project was to design and build a prototype small scale photovoltaic (PV) powered autonomous airship. The principle reason for the construction of the unmanned airship was to investigate the possibility of using self-guided, lighter-than-air aircraft as an alternative to earth observational satellites for the purposes of terrain mapping and imaging. The necessary electrical energy was produced by single crystal photovoltaic solar cells. The airship was designed to carry an onboard battery in order to provide power generation in the case of intermittent cloud coverage. It was also designed to interface with an Arduino prototyping board which …
Warehouse Design For Polygait, Colby Spear
Warehouse Design For Polygait, Colby Spear
Industrial and Manufacturing Engineering
Professor Tali Freed, advisor of POLY GAIT, needs a warehouse built to accommodate the testing of Radio Frequency Identification (RFID) technology with Automatic Storage and Retrieval Systems (AS/RS). This report explores a 5-step warehouse designing technique. The five steps are as follows: Overall Structure, Sizing and Dimensioning, Operation Strategy Selection, Equipment Selection, and Department Layout. Each of these is analyzed in turn to cover everything necessary in designing a warehouse. Furthermore, a cost analysis was conducted in order to give Professor Freed a better understanding on the cost required to build this warehouse. A smaller 25’x22’ foot is optimal because …
Olympic Bocce Ballers, Steven Erickson, William Haley, Taylor Vaughan
Olympic Bocce Ballers, Steven Erickson, William Haley, Taylor Vaughan
Mechanical Engineering
No abstract provided.
Design Of A Micro Irrigation System For An Almond Orchard, Adam Scheuber
Design Of A Micro Irrigation System For An Almond Orchard, Adam Scheuber
BioResource and Agricultural Engineering
The owners of Scheuber Farms, a 1,000 acre row crop farming operation located in Patterson, California, wish to convert a 15-acre field into an almond orchard. For irrigating the trees, they would like to use a microsprayer irrigation system. The design I recommend and describe in this paper utilizes proper hydraulic analysis, and is based on the ability to supply enough water to match the amount of water required by the orchard during the peak month of an average year.
All of the major components and parameters of the microsprayer irrigation system were designed at minimal cost while ensuring that …
Design Of Equipment For The Study Of Non-Isothermal Flow In Polymer Fluid, Opeoluwa Oluwaseun Kolawole
Design Of Equipment For The Study Of Non-Isothermal Flow In Polymer Fluid, Opeoluwa Oluwaseun Kolawole
Masters Theses
The polymer industry is an ever growing industry, and, as it grows, companies are continuously looking for ways to study and understand the behaviors of polymers in relation to the processing and production. This is to ensure the production of high quality products and to improve existing products.
An important parameter during polymer processing is temperature. Temperature control affects several rheological parameters such as viscosity, and in turn the quality of the final products. Frictional or viscous heating is a very important part of polymer processing and occurs in almost every polymer processing operation.
The objective of this research is …
Investigation Of The Design And Static Behavior Of Cylindrical Tubular Composite Adhesive Joints Utilizing The Finite Element Method And Stress-Based Failure Theories, Michael D. Lambert
Investigation Of The Design And Static Behavior Of Cylindrical Tubular Composite Adhesive Joints Utilizing The Finite Element Method And Stress-Based Failure Theories, Michael D. Lambert
All Graduate Theses and Dissertations, Spring 1920 to Summer 2023
The stress and strength behavior of cylindrical tubular adhesive joints composed of dissimilar materials was explored. This was accomplished with the finite element method (FEM) and stress-based failure theories. Also, it was shown how a design of experiments (DOE) based method can be used to objectively organize the process of optimizing joint strength by using stress-based failure criteria.
The finite element program used in this work was written in-house from scratch to implement the FEM for the purpose of solving both axisymmetric and three-dimensional linear elastic governing equations of static equilibrium. The formulation of the three-dimensional model is presented, and …
Design Of Online Student Fee Committee Proposal Information System, Kenneth Cairns, Gregory (Greg) Jacobson
Design Of Online Student Fee Committee Proposal Information System, Kenneth Cairns, Gregory (Greg) Jacobson
Industrial and Manufacturing Engineering
The purpose of this project is to overhaul the IME department’s Student Fee Committee (SFC) proposal system. A web enabled database was designed in order to improve this system. A significant amount of time was spent researching different programming languages, paradigms, and frameworks in order to determine the most logical approach to the system redesign. After a few false leads, it was determined that the most appropriate solution to the problem was to design a C# based web form application using asp.NET technology, developed in Microsoft Visual Studio. A mockup was created in Access in an attempt to determine if …
Probabilistic Structural And Thermal Analysis Of A Gasketed Flange, Atul G. Tanawade
Probabilistic Structural And Thermal Analysis Of A Gasketed Flange, Atul G. Tanawade
ETD Archive
Performance of a flange joint is characterized mainly by its 'strength' and 'sealing capability'. A number of analytical and experimental studies have been conducted to study these characteristics under internal pressure loading. However, with the advent of new technological trends for high temperature and pressure applications, an increased demand for analysis is recognized. The effect of steady-state thermal loading makes the problem more complex as it leads to combined application of internal pressure and temperature. Structural and thermal analysis of a gasketed flange was computationally simulated by a finite element method and probabilistically evaluated in view of the several uncertainties …
A Left Ventricular Motion Phantom For Cardiac Magnetic Resonance Imaging, Mehmet Ersoy
A Left Ventricular Motion Phantom For Cardiac Magnetic Resonance Imaging, Mehmet Ersoy
ETD Archive
The mammalian left ventricle (LV) has two distinct motion patterns: wall thickening and rotation. The purpose of this study was to design and build a low-cost, non-ferromagnetic LV motion phantom, for use with cardiac magnetic resonance imaging (MRI), that is able to produce physiologically realistic LV wall thickening and rotation. Cardiac MRI is continuously expanding its range of techniques with new pulse sequences, including new tissue tagging techniques which allow intra-myocardial deformation to be visualized. An essential step in the development of new cardiac MRI techniques is validating their performance in the presence of motion. MRI-compatible dynamic motion phantoms are …
Design, Fabrication And Characterization Of A New Wind Tunnel Facility – Linear Cascade With A Wake Simulator, Jean-Philippe Junca-Laplace
Design, Fabrication And Characterization Of A New Wind Tunnel Facility – Linear Cascade With A Wake Simulator, Jean-Philippe Junca-Laplace
LSU Master's Theses
A new wind tunnel has been designed and constructed at the LSU Mechanical Engineering Laboratories. The objective was to design a versatile test facility, suitable for a wide range of experimental measurements on turbine blades. The future study will investigate the impact of unsteady inflow conditions on film cooling performance. More specifically, it will study how the unsteady flow due to the upstream passing wakes coming from the front row vane affects the film cooling performances on the turbine blades. The test section consists of a four passage linear cascade composed of three full blades and two shaped wall blades. …
Design Of A Liquid Fuel Injector For Alternative Fuel Studies In An Atmospheric Model Gas Turbine Combustor, John Stevenson
Design Of A Liquid Fuel Injector For Alternative Fuel Studies In An Atmospheric Model Gas Turbine Combustor, John Stevenson
Honors Theses
A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes …
Design Space Decomposition Using Concept Maps, David E. Robbins
Design Space Decomposition Using Concept Maps, David E. Robbins
All ETDs from UAB
Decomposition of engineering design spaces has been performed primarily through statistical and system identification techniques. However, no approach has yet attempted to capture the semantics of a design through decomposition. This thesis presents graphical techniques for capturing the semantics of a design by developing an information architecture through design space decomposition using concept maps. In particular, concept maps are used to begin identifying the top layers of the information architecture of a problem, which has the dual effects of performing an initial decomposition of the design space and refining the parameters that will define more detailed design spaces for further …