Digital Commons Network^™

Reverse Decision Making And Goal Attainment A Proof Of Concept As A New Approach To The Decision Making Process Under Uncertainty, Shitalkumar S. Sabne

Engineering Management & Systems Engineering Theses & Dissertations

Decision making occurs when one must choose among alternatives. However, in uncertain environments where problems are complex and decision makers lack complete knowledge of the situation as well as decision alternatives, it's not possible for them to select an optimal decision outcome by 'Traditional Decision Approaches'. At present Reverse Decision Making is the central, although new and unproved, approach of Old Dominion University's Engineering Management and Systems Engineering research on decision making process for uncertain and complex situations. Even though research in decision making spans over one hundred years, there are still important problems which remain to be addressed.

There …

An Empirical Investigation Into The Relationships Between Emotional Intelligence, Use Of Knowledge Transfer Methods, And Project Performance, Brent Michael Decker

Engineering Management & Systems Engineering Theses & Dissertations

Increasingly, the use of project teams is becoming commonplace within organizations as the primary means to accomplish complex tasks. While the literature has long acknowledged that the knowledge transfer process is a key component in achieving organizational success and ultimately sustaining a competitive advantage, very little has been written that specifically examines the knowledge transfer process at the project team level. In an attempt to increase the understanding of knowledge transfer processes at the project team level, the effect that a relatively new construct, termed emotional intelligence, has on the use of knowledge transfer methods is examined. The relationships between …

Development Of A Theoretical Framework Of Distributed Cognition Phenomena In Control Centers During Crisis Conditions, Christopher J. West

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this research is to develop and partially validate a theoretical framework describing distributed cognition phenomena occurring in organizational control centers functioning in crisis environments. Using a systems approach, the work synthesizes existing constructs relating to distributed cognition then supplements this knowledge with review of crisis management literature. The goal of this effort is the development of a framework for understanding the impact of crisis conditions on such phenomena occurring within the specified setting. An exploratory case study approach was used to partially validate and refine the framework by gauging its ability to interpret the impact of crisis …

High Performance Queueing And Scheduling In Support Of Multicasting In Input-Queued Switches, Weiying Zhu

Electrical & Computer Engineering Theses & Dissertations

Due to its mild requirement on the bandwidth of switching fabric and internal memory, the input-queued architecture is a practical solution for today's very high-speed switches. One of the notoriously difficult problems in the design of input-queued switches with very high link rates is the high performance queueing and scheduling of multicast traffic. This dissertation focuses on proposing novel solutions for this problem. The design challenge stems from the nature of multicast traffic, i.e., a multicast packet typically has multiple destinations. On the one hand, this nature makes queueing and scheduling of multicast traffic much more difficult than that of …

Performance Analysis Of Recoverable Flight Control Systems Subject To Neutron-Induced Upsets Using Hybrid Dynamical Models, Hong Zhang

Electrical & Computer Engineering Theses & Dissertations

It has been observed that atmospheric neutrons can produce single-event upsets in digital flight control hardware. Potentially, they can reduce system performance and introduce a safety hazard. One experimental system-level approach investigated to help mitigate the effects of these upsets is NASA Langley's Recoverable Computer System. It employs rollback error recovery using dual-lock-step processors together with new fault tolerant architectures and communication subsystems.

In this dissertation, a class of stochastic hybrid dynamical models, which consists of a jump-linear system and a stochastic finite-state automaton, is used to describe the performance of a Boeing 737 aircraft system in closed-loop with a …

Micron-Level Actuator For Thermal-Fluid Control In Microchannels, Nurhak Erbas

Mechanical & Aerospace Engineering Theses & Dissertations

Effectiveness of an actuator is investigated for thermal-flow control in microchannels. First, simulations of a single actuator in a quiescent external medium are performed in order to study the parameters characterizing the synthetic jet flow from the actuator. For this purpose, a simplified, two-dimensional configuration is considered. The membrane motion is modeled in a realistic manner as a moving boundary in order to accurately compute the flow inside the actuator cavity. The geometric and actuation parameters of the actuator are investigated to define the effectiveness of the jet flow. The study is done initially at macro scales. Then, the flow …

An Adaptive Algorithm To Identify Ambiguous Prostate Capsule Boundary Lines For Three-Dimensional Reconstruction And Quantitation, Rania Yousry Hussein

Electrical & Computer Engineering Theses & Dissertations

Currently there are few parameters that are used to compare the efficiency of different methods of cancerous prostate surgical removal. An accurate assessment of the percentage and depth of extra-capsular soft tissue removed with the prostate by the various surgical techniques can help surgeons determine the appropriateness of surgical approaches. Additionally, an objective assessment can allow a particular surgeon to compare individual performance against a standard. In order to facilitate 3D reconstruction and objective analysis and thus provide more accurate quantitation results when analyzing specimens, it is essential to automatically identify the capsule line that separates the prostate gland tissue …

Learning As A Nonlinear Line Of Attraction For Pattern Association, Classification And Recognition, Ming-Jung Seow

Electrical & Computer Engineering Theses & Dissertations

Development of a mathematical model for learning a nonlinear line of attraction is presented in this dissertation, in contrast to the conventional recurrent neural network model in which the memory is stored in an attractive fixed point at discrete location in state space. A nonlinear line of attraction is the encapsulation of attractive fixed points scattered in state space as an attractive nonlinear line, describing patterns with similar characteristics as a family of patterns.

It is usually of prime imperative to guarantee the convergence of the dynamics of the recurrent network for associative learning and recall. We propose to alter …

Introducing The Engineering Technology Programs To All Incoming Freshmen Engineering And Technology Students–The Result Is Better For All, Gary Crossman, Anthony Dean

Engineering Technology Faculty Publications

The Department of Engineering Technology at Old Dominion University participates in a freshman engineering course sequence, along with four engineering departments in the Batten College of Engineering and Technology. The two course sequence, Exploring Engineering and Technology I and II, involve the five departments in teaching at least one five week module in each of the two courses. Each department generally involves the students in a basic design project related to its discipline. Since the Department of Engineering Technology has three main programs – Civil, Electrical, and Mechanical – it has elected to divide its five week segment into three …

Improving Efficiency In Engineering Design Using Augmented D-Optimal Designs 'Synthetic Jet' Design Optimization Study, Fatih Erdogan

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this thesis is to study the efficiency of several "design of experiments" (DOE) approaches used for the analysis and optimization of engineering designs. A literature review is conducted to study various "design of experiments" methods and the advantages and limitations of each method are discussed.

As an application, Augmented D-Optimal designs are utilized for a design study of 'synthetic jet'.

With the objective of improving efficiency and providing a minimum point experimental design model, computer-aided D-optimal method is preferred for this study. For setting up the design of the experiments and for performing the analysis of results, …

Crisis Management In Projects, Senol Nazikkol

Engineering Management & Systems Engineering Theses & Dissertations

The objective of this investigation is to identify the processes, benefits and important tools of crisis management in projects. Crisis management is a system that helps managers to prevent and overcome crises. In this research, a general review about crisis, crisis management processes and tools are discussed. The research was done by using the information in the literature and expert judgment. This paper can be used by academics as a foundation for further research and development in the area of crisis management in projects. Managers of projects can use this study for improving their projects and project-based organizations' crisis management …

A Comparative Analysis Of Air-To-Ground Engagement Outcomes In The Joint Warfare System (Jwars) And The Jwars-Joint Semi-Automated Forces Federation, Melissa Anne St. Peter

Computational Modeling & Simulation Engineering Theses & Dissertations

Multi-resolution modeling is the process by which a single model is created by connecting multiple individual models to describe phenomena at different levels of resolution [1]. "When we change resolutions, replacing a detailed model by a more aggregate one, we must ask whether results are 'consistent'" [2].

There are many methods of determining if the results of two simulations are 'consistent'. However, they are very entailed and require a detailed understanding of the individual models including their functionality, algorithms, and inner workings. A straight forward and rapid way of assessing potential inconsistencies is through a statistical comparison of the model …

Atmospheric-Pressure Plasma Sources For Polymer Surface Modification, Shujun Yang

Electrical & Computer Engineering Theses & Dissertations

Plasma processing is widely used in the microelectronics industry for deposition of thin films. It is also used in etching of semiconductors, metals and organic materials such as photoresists. In addition, plasmas are widely used to modify material surfaces. Plasma surface modification can improve the surface adhesion of polymeric materials, which can be used as insulating layers in multilayer semiconductor structures. In deposition and etching, relatively a large amount of material is added to or removed from the surface. In plasma surface modification, only the surface layer is changed in composition or structure, and no significant amount of material is …

Boundary Interference Assessment And Correction For Open Jet Wind Tunnels Using Panel Methods, Wael Ahmed Mokhtar

Mechanical & Aerospace Engineering Theses & Dissertations

The presence of nearby boundaries in a wind tunnel can lead to aerodynamic measurements on a model in the wind tunnel that differ from those that would be made when the boundaries of the moving fluid were infinitely far away. The differences, referred to as boundary interference or wall interference, can be quite large, such as when testing aircraft models developing high lift forces, or whose wingspan is a large fraction of the wind tunnel width, or high drag models whose frontal area is a large fraction of the tunnel cross section. Correction techniques for closed test section (solid walled) …

Passive And Active Nonlinear Control Of Ship Roll Motions Using U-Tube Tanks, Thongchai Phairoh

Mechanical & Aerospace Engineering Theses & Dissertations

A U-tube water tank is first designed to roll a ship floating on still water. The 6-degree of freedom (DOF) dynamic model of U-tube tank is derived and the effects of its parameters on ship roll motion are studied. Numerical simulations show that the U-tube tank is an effective stimulator to roll the ship on still water. For a rolling ship, the U-tube tank can be used as a damper to reduce ship roll motion quickly.

Active control of ship roll motion with a proportional and derivative (PD) controller, linear quadratic regulator (LQR), generalized predictive control (GPC), and deadbeat predictive …

Mechanical Properties And Durability Of A Composite Material At Cryogenic Temperatures, Ray Walton Grenoble

Mechanical & Aerospace Engineering Theses & Dissertations

Several issues relevant to the use of a high-performance graphite-epoxy material in hydrogen storage tank applications have been examined. The tensile properties of IM7/977-2 were evaluated as a function of test temperature and thermal-mechanical load history. The temperature dependent coefficient of thermal expansion (CTE) of unidirectional specimens of the same material was measured between -200°C and 0°C. The effects of test temperature, mechanical loading, and damage state on the leak rate of hydrogen gas through IM7/977-2 laminates were evaluated using a novel test system. Finally, the mechanical properties of several commercially available polymer films, which might prove useful as leak-resistant …

An Analysis Of Indicator Organism Suitability For Lower James And York Rivers, Rhonda Ashonti Ford

Civil & Environmental Engineering Theses & Dissertations

The primary objectives of this thesis are (1) determine if the proper indicator organism is being utilized to determine the bacterial water quality in the State of Virginia. (2) If other environmental factors can predict the bacterial water quality. The current indicator organism of choice for bacterial water quality of waters in the State of Virginia is enterococci, for estuarine and brackish waters. E. coli is the indicator organism of choice for fresh waters in Virginia.

The study concluded (1) Enterococci are the best indicator organism for beaches located in the Hampton Roads Harbor and the Lower James River. (2) …

Whole Word Phonetic Displays For Speech Articulation Training, Fansheng Meng

Electrical & Computer Engineering Theses & Dissertations

The main objective of this dissertation is to investigate and develop speech recognition technologies for speech training for people with hearing impairments. During the course of this work, a computer aided speech training system for articulation speech training was also designed and implemented. The speech training system places emphasis on displays to improve children's pronunciation of isolated Consonant-Vowel-Consonant (CVC) words, with displays at both the phonetic level and whole word level. This dissertation presents two hybrid methods for combining Hidden Markov Models (HMMs) and Neural Networks (NNs) for speech recognition. The first method uses NN outputs as posterior probability estimators …

Gis And 3d Analysis Applied To Sea Turtle Mortalities And Navigation Channel Dredging, Bradley A. Shellito, Keith B. Lockwood

Virginia Journal of Science

Between 2000 and 2003 there were an increased number of documented sea turtle mortalities related to hopper dredging in the channels of the Chesapeake Bay. A pilot study was undertaken to create a bathymetric surface and three-dimensional model of the Cape Henry Channel using Geographic Information Systems (GIS) as a visualization tool to examine sea turtle mortalities in relation to the dredging. In Fall 2003, the US Army Corps of Engineers dredged the Thimble Shoals Federal Navigation Channel, and a more refined model was developed using this data. This project examines the growing concerns over sea turtle mortality rates and …

Nanoelectropulse-Driven Membrane Perturbation And Small Molecule Permeabilization, P. Thomas Vernier, Yinghua Sun, Martin A. Gundersen

Bioelectrics Publications

Background
Nanosecond, megavolt-per-meter pulsed electric fields scramble membrane phospholipids, release intracellular calcium, and induce apoptosis. Flow cytometric and fluorescence microscopy evidence has associated phospholipid rearrangement directly with nanoelectropulse exposure and supports the hypothesis that the potential that develops across the lipid bilayer during an electric pulse drives phosphatidylserine (PS) externalization.

Results
In this work we extend observations of cells exposed to electric pulses with 30 ns and 7 ns durations to still narrower pulse widths, and we find that even 3 ns pulses are sufficient to produce responses similar to those reported previously. We show here that in contrast to …

Variational Approach To The Volume Viscosity Of Fluids, Allan J. Zuckerwar, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

The variational principle of Hamilton is applied to develop an analytical formulation to describe the volume viscosity in fluids. The procedure described here differs from those used in the past in that a dissipative process is represented by the chemical affinity and progress variable (sometimes called "order parameter") of a reacting species. These state variables appear in the variational integral in two places: first, in the expression for the internal energy, and second, in a subsidiary condition accounting for the conservation of the reacting species. As a result of the variational procedure, two dissipative terms appear in the Navier-Stokes equation. …

Using Rfid Technology In Collaborative Design Of The Assembly Systems, Stevan Stankovski, Gordana Ostojić, Vukica Jovanović, Branislav Stevanov

Engineering Technology Faculty Publications

Modern production conditions require the application of the concept of distributing production. This approach means coordinative production in a number of small and middle size companies. Multiplex products, consisting of a number of parts, components, and modules are assembled in one function unit in one company, but they may not be manufactured in one place. Huge factory and production complex, which existed in our country, comprised all phases of product lifecycle, from the development of a concept solution to the assembly. Technology of product manufacturing, resource logistics, quality control, product testing and verification of product function characteristics all represented activities …

An Assessment And Continuous Improvement Model For Engineering Technology Programs, Alok Verma, Gary Crossman

Engineering Technology Faculty Publications

Assessment and continuous improvement are essential and critical processes for higher education. Development and implementation of such processes are not only required by the Accreditation Board for Engineering and Technology (ABET) but it is also a necessary condition for the maturation and development of any engineering technology program. The assessment and continuous improvement plan discussed here was developed at Old Dominion University (ODU) and implemented during the last accreditation cycle within the Engineering Technology Department. The plan is based on two cycles of assessment and evaluation, a short cycle of one year and a long term cycle of three years. …

Ontological Implications Of The Levels Of Conceptual Interoperability Model, Andreas Tolk, Charles D. Turnitsa, Saikou Y. Diallo

Computational Modeling & Simulation Engineering Faculty Publications

The Levels of Conceptual Interoperability Model (LCIM) was developed to cope with the different layers of interoperation of modeling & simulation applications. It introduced technical, syntactic, semantic, pragmatic, dynamic, and conceptual layers of interoperation and showed how they are related to the ideas of integratability, interoperability, and composability. This paper will be presented in the invited session "Ontology Driven Interoperability for Agile Applications using Information Systems: Requirements and Applications for Agent Mediated Decision Support" at WMSCI 2006.

Plasma Membrane Voltage Changes During Nanosecond Pulsed Electric Field Exposure, W. Frey, R. O. Price, P. F. Blackmore, R. P. Joshi, R. Nuccitelli, S. J. Beebe, K. H. Schoenbach, J. F. Kolb

Bioelectrics Publications

The change in the membrane potential of Jurkat cells in response to nanosecond pulsed electric fields was studied for pulses with a duration of 60 ns and maximum field strengths of similar to 100 kV/cm (100 V/cell diameter). Membranes of Jurkat cells were stained with a fast voltage-sensitive dye, ANNINE-6, which has a subnanosecond voltage response time. A temporal resolution of 5 ns was achieved by the excitation of this dye with a tunable laser pulse. The laser pulse was synchronized with the applied electric field to record images at times before, during, and after exposure. When exposing the Jurkat …

Designing A Microcontroller Training Platform For Active Distance Learning Engineering And Technology Students, Steve C. Hsiung, James E. Eiland, John R. Hackworth, John Ritz

Engineering Technology Faculty Publications

This is an active distance-learning project that addresses the hands-on microprocessor/ mi-crocontroller-related courses. A research team designed a low-cost training system with supporting instructional materials to assist the teaching of these concepts. Individual laboratory activities are being developed to reinforce student learning and skill development in programming concepts. This basic system format eventually will support an array of engineering and technology courses. This project involves two community colleges, Blue Ridge Community College (BRCC) and Olympic College (OC), and a four-year university, Old Dominion University (ODU), in a collaborative research team to design and develop a specific PIC microcontroller training system …

Observed Web Robot Behavior On Decaying Web Subsites, Joan A. Smith, Frank Mccown, Michael L. Nelson

Computer Science Faculty Publications

We describe the observed crawling patterns of various search engines (including Google, Yahoo and MSN) as they traverse a series of web subsites whose contents decay at predetermined rates. We plot the progress of the crawlers through the subsites, and their behaviors regarding the various file types included in the web subsites. We chose decaying subsites because we were originally interested in tracking the implication of using search engine caches for digital preservation. However, some of the crawling behaviors themselves proved to be interesting and have implications on using a search engine as an interface to a digital library.

Fedcor: An Institutional Cordra Registry, Giridhar Manepalli, Henry Jerez, Michael L. Nelson

Computer Science Faculty Publications

FeDCOR (Federation of DSpace using CORDRA) is a registry-based federation system for DSpace instances. It is based on the CORDRA model. The first article in this issue of D-Lib Magazine describes the Advanced Distributed Learning-Registry (ADL-R) [1], which is the first operational CORDRA registry, and also includes an introduction to CORDRA. That introduction, or other prior knowledge of the CORDRA effort, is recommended for the best understanding of this article, which builds on that base to describe in detail the FeDCOR approach.

A New Approach In Microprocessor/Microcontroller Courses/Laboratories Material Design And Development, Steve C. Hsiung, Jeff Willis

Engineering Technology Faculty Publications

Courses in microprocessors and microcontrollers are standard parts of the Engineering Technology core curricula. The traditional course material developments include both lectures and associated laboratory exercises. No matter how creative is the curriculum; it is usually budgetary constraints that confine the creativity when developing new curricula. This limits the freedom of the major approach in new course development.

This article demonstrates new course lecture and laboratories material development that starts from ground up with both a hardware platform and simulation software design for microprocessor/microcontroller related courses. It is not only very cost effective, but also does not limit the instructor's …

A Comparison Between Frequent Out-Of-Class Assignments And Frequent In-Class Assessments Relative To Student Performance In A Sophomore Level Electrical Circuit Analysis Course, Isaac Flory, Christian Hearn

Engineering Technology Faculty Publications

Two parallel sections of a sophomore level circuit analysis course in Electrical Engineering Technology were structured to provide insight to the marginal utility of out-of-class assignments versus in-class assessments in academic performance. Student distributions for each section, the classroom model, the composition of the common tests and exam, and grading formats are discussed. The data presented and the conditions of the resulting observations indicate the model which favored out-of-class assignments led to improved test scores.