Digital Commons Network^™

Magnetic Field Effects On Lithium Ion Batteries, Kevin Mahon

Theses

The Nobel Prize in Chemistry 2019 was just recently awarded to John B. Goodenough, M. Stanley Whittingham, and Akira Yoshino for the development of lithium-ion batteries. Lithium-ion batteries have seen use in many different industries and applications such as in portable devices, power grids, and electric vehicles. As lithium-ion batteries become more commonplace they will need to be modeled more extensively. The magnetic field effect on lithium-ion batteries has not been studied significantly since they were first discovered.

Modeling these batteries is still difficult because of the many complexities of the operation of a battery. Lithium-ion batteries are commonly modeled …

Study And Modelling Of Lithium Ion Cell With Accurate Soc Measurement Algorithm Using Kalman Filter For Electric Vehicles, Kasthuriramanan Mahendravadi Sivaguru

Theses

Lithium Ion cells are preferred over lead acid cells for electric vehicles due to their energy density, higher discharge current and size. The cost of lithium ion cells is scaling down compared to ten years earlier, but as their performance characteristics increase, the need for safety and accurate modelling also increases.

The absence of a generic cell model is associated to the different makes of cells and different chemistries of Lithium ion cells behave differently under the testing conditions required for every unique application. The focus of this thesis will be on how to provide intelligence to the battery management …

Reducing The Production Cost Of Semiconductor Chips Using (Parallel And Concurrent) Testing And Real-Time Monitoring, Qutaiba Khasawneh

Electrical Engineering Theses and Dissertations

Consumer electronics changed the semiconductor industry by developing many new challenges for consumer products. One of the main challenges in the consumer product is that it propelled the volume of production to massive production, e.g. hundreds of millions of cell phones are produced yearly. Combined with the overproduction of consumer products, price pressure is another challenge for consumer products. Many of the new techniques used in the design and fabrication enabled the integration of more devices in the same chips. This reduced the cost of the chips, lowered the power consumption, increased the circuit operation speed, enabled more reliable implementation, …

Kernel Methods For Graph-Structured Data Analysis, Zhen Zhang

McKelvey School of Engineering Theses & Dissertations

Structured data modeled as graphs arise in many application domains, such as computer vision, bioinformatics, and sociology. In this dissertation, we focus on three important topics in graph-structured data analysis: graph comparison, graph embeddings, and graph matching, for all of which we propose effective algorithms by making use of kernel functions and the corresponding reproducing kernel Hilbert spaces.For the first topic, we develop effective graph kernels, named as "RetGK," for quantitatively measuring the similarities between graphs. Graph kernels, which are positive definite functions on graphs, are powerful similarity measures, in the sense that they make various kernel-based learning algorithms, for …

A Wearable Mechatronic Device For Hand Tremor Monitoring And Suppression: Development And Evaluation, Yue Zhou

Electronic Thesis and Dissertation Repository

Tremor, one of the most disabling symptoms of Parkinson's disease (PD), significantly affects the quality of life of the individuals who suffer from it. These people live with difficulties with fine motor tasks, such as eating and writing, and suffer from social embarrassment. Traditional medicines are often ineffective, and surgery is highly invasive and risky. The emergence of wearable technology facilitates an externally worn mechatronic tremor suppression device as a potential alternative approach for tremor management. However, no device has been developed for the suppression of finger tremor that has been validated on a human.

It has been reported in …

A Comparative Study On The Stability And Degradation Of Perovskite Solar Cells, Jyotiska Chakraborty

Masters Theses

This study aims to investigate the environmental factors that affect the performance and longterm stability of the perovskite solar cells (PSCs). PSCs are based on organo-metallic halides (perovskites) that act as a light-sensitive compound that produces excitons when placed under the light. However, PSCs have a limited operating lifetime due to the degradation of the perovskite layer. There are many factors like moisture, UV light, and temperature that lead to the degradation of the perovskite layer. From the literature review, it was found that the PSCs do not degrade with the presence of oxygen in a dry and dark environment. …

Load Flow Analysis Of 138/69kv Substation Using Electrical Transient & Analysis Program (Etap), Vanessa Abadia Gomez

Electrical Engineering Undergraduate Honors Theses

This paper examines the load flow analysis of a high-voltage substation using ETAP, and explores options for improving the voltage profile of the system. This study yields critical information about the system, such as the voltage drop at each feeder, the voltage at each bus, as well as real and reactive power losses at the different branches and feeders. In this power flow examination, the system’s performance is evaluated for different operating conditions, so that control measurements can be applied if necessary. The experimental results are used for proposing a plan of using fixed and switched shunt capacitor banks to …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Assessment Of Sensory Abnormalities In Children With Asd Using Virtual Reality, Ankit Koirala

Theses and Dissertations

Sensory abnormality is one of the important characteristics of Autism Spectrum Disorder(ASD). A large number of studies suggest a strong connection between sensory abnormalities and ASD. Therefore, it is important to assess sensory abnormalities for diagnosis and intervention of ASD. In this thesis study, we aim to develop a virtual reality system that can measure sensory abnormalities in adolescents with ASD. Sensory abnormalities can affect all five senses: touch, vision, smell, taste and auditory. However, in this study, we focus on assessing sensory abnormality in vision and touch sensory processing. Twelve adolescents with ASD and 12 typically developing (TD) adolescents …

Vehicle Interior Access Deployable Worksurface Mechanism Concept Product Design, Premchand Gunachandran

Theses and Dissertations

by

Premchand Gunachandran

The University of Wisconsin-Milwaukee, 2019

Under the Supervision of Professor Mohammad Habibur Rahman

Easy access and adjusting the vehicle interior configuration to a variety of situations and uses is the general desire for any vehicle user. To meet such desire an attempt has been made in this study to conceptualize a design to develop a new mechatronic product called re-configurable vehicle interior console mechanism to deploy a worksurface (DWS), which will provide flexible use of the vehicle’s interior of both partial and fully autonomous vehicles. This re-configurable vehicle interior console will deploy the DWS using a power …

Scatter Reduction By Exploiting Behaviour Of Convolutional Neural Networks In Frequency Domain, Carlos Ivan Jerez Gonzalez

Theses and Dissertations

In X-ray imaging, scattered radiation can produce a number of artifacts that greatly

undermine the image quality. There are hardware solutions, such as anti-scatter grids.

However, they are costly. A software-based solution is a better option because it is

cheaper and can achieve a higher scatter reduction. Most of the current software-based

approaches are model-based. The main issues with them are the lack of flexibility, expressivity, and the requirement of a model. In consideration of this, we decided to apply

Convolutional Neural Networks (CNNs), since they do not have any of the previously

mentioned issues.

In our approach we split …

Cavity Environmental Control System Upgrade For Nasa’S Stratospheric Observatory For Infrared Astronomy, Ashraf Al-Hajjeh

Theses and Dissertations

The main goal of this project is to fulfill the need of a controller upgrade for the Cavity Environmental Control System (CECS) on NASA’s Stratospheric Observatory for Infrared Astronomy (SOFIA) aircraft. The preceding controller had multiple disadvantages including operating in an unpressurized region, incomplete functionality implementation, limited fault and status monitoring capability, and reduced maintainability and reliability. The new controller will go through the NASA design process to fulfill all the requirements of CECS operation including complete functionality of all devices currently installed on the aircraft, added devices to improve fault and health monitoring, and overall improvement in maintainability and …

Demand-Side Load Management Using Single-Phase Residential Static Var Compensators, Muhammad Kamran Latif

Boise State University Theses and Dissertations

Distribution systems are going through a structural transformation from being radially-operated simple systems to becoming more complex networks to operate in the presence of the distributed energy resources (DERs) with significant levels of penetration. It is predicted that the share of electricity generation from DERs will keep increasing as the world is moving away from the power generation involving carbon-emission and towards cleaner energy sources such as solar, wind, and biofuels. However, the unstable behavior of the renewables resources presents challenges to the already existing distribution systems. One such problem is when the distribution feeder experience variable power supply due …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Development Of A Simulated Tangle-Based Microgrid Communications System, Adrian Vincent T. Tayag

Undergraduate Theses

The emergence of renewable energy sources (RES) brought up the potential advantages of more granular controls that Microgrids offer. In this study, Tangle-based-decentralized ledger technology was implemented to the communications system of a fabricated prototype microgrid. The microgrid controls were managed by a Raspberry Pi 3 Model B+ minicomputer, where the energy manager, protection coordinator, and microsource controller agents are running. Through the Masked Authenticated Messaging (MAM) module of the IOTA Tangle ledger, the grid operator was able to act as an energy manager to send commands and receive status reports from the protection coordinator and microsource controller. The fabricated …

Exploring Methods For Studying Recoverability Of Shipboard Electrical Power Distribution Systems, Jacob David Gudex

Theses and Dissertations

Advancement of the technology included on ships, is changing the nature of loads installed on ships. Not only are there more loads than installed power generation, but advanced electrically powered weapons and sensors are changing the profile of the installed loads. These are challenges for future shipboard power systems design. Challenges which must be solved with careful distribution system planning, energy storage integration, and selection of individual power electronic converters within the ship. Different topologies and distribution systems have differing fault isolation and recovery (FIR) capability sets, which affects ship survivability. Furthermore, different FIR capability sets, operate at different speeds. …

Design, Modeling And Control Of A Two-Wheel Balancing Robot Driven By Bldc Motors, Charles T. Refvem

Master's Theses

The focus of this document is on the design, modeling, and control of a self-balancing two wheel robot, hereafter referred to as the balance bot, driven by independent brushless DC (BLDC) motors. The balance bot frame is composed of stacked layers allowing a lightweight, modular, and rigid mechanical design. The robot is actuated by a pair of brushless DC motors equipped with Hall effect sensors and encoders allowing determination of the angle and angular velocity of each wheel. Absolute orientation measurement is accomplished using a full 9-axis IMU consisting of a 3-axis gyroscope, a 3-axis accelerometer, and a 3-axis magnetometer. …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Novel Control Of Pv Solar Farms As Statcom (Pv-Statcom) For Frequency Control And Power Oscillation Damping, Mohammad Akbari Kelishadi

Electronic Thesis and Dissertation Repository

Frequency stability and low-frequency power oscillations are two major concerns in modern power systems. PV-STATCOM is a patented concept which enables PV inverters to provide STATCOM functions, during day and night, as well as real power modulation during daytime. This thesis aims to utilize PV-STATCOM capability effectively for enhancing frequency stability and power oscillations damping.

A novel, simultaneous real power-based Fast Frequency Response (FFR) and reactive power-based Power Oscillation Damping (POD) control is proposed for PV-STATCOMs. This control not only significantly reduces system under- and over-frequency deviations, but also uses the unutilized capacity of PV inverters to enhance damping of …

Indocyanine-Green-Assisted Near-Infrared Dental Fluorescence Imaging To Detect Common Dental Diseases, As Compared With Dental X-Ray, Yoshita Viraj Holamoge

LSU Master's Theses

Oral health is indicative of a person’s overall health. Even with advances in medical science, dental diseases are very much prevalent in our society. Dental imaging techniques help in the early detection of these dental diseases and eventually avoids the risk of poor oral health as well as medical expenses. Current dental imaging techniques rely mostly on X-ray imaging whose ionizing property is a concern amongst the population. Near-infrared spectrum is known to have tissue penetration property and they belong to the non-ionizing part of the electromagnetic spectrum. This study utilized a contrast agent assisted near-infrared imaging for common dental …

5-Bit Dual-Slope Analog-To-Digital Converter-Based Time-To-Digital Converter Chip Design In Cmos Technology, Jojoe S. Sagoe

LSU Master's Theses

Time-to-Digital Converters (TDC) have gained increasing importance in modern implementations of mixed-signal, data-acquisition and processing interfaces and are used to perform high precision time intervals in systems that incorporate Time-of-Flight (ToF) or Time-of-Arrival (ToA) measurements. The linearity of TDCs is very crucial since most Digital Signal Processing (DSP) systems require very linear inputs to achieve high accuracy.

In this work, a TDC has been designed in the 0.5 μm n-well CMOS process that can be used for on-chip integration and in applications requiring high linearity. This TDC used a Dual-Slope-ADC-based architecture for the time-to-digital conversion and consists of the following …

Adaptive-Hybrid Redundancy For Radiation Hardening, Nicolas S. Hamilton

Theses and Dissertations

An Adaptive-Hybrid Redundancy (AHR) mitigation strategy is proposed to mitigate the effects of Single Event Upset (SEU) and Single Event Transient (SET) radiation effects. AHR is adaptive because it switches between Triple Modular Redundancy (TMR) and Temporal Software Redundancy (TSR). AHR is hybrid because it uses hardware and software redundancy. AHR is demonstrated to run faster than TSR and use less energy than TMR. Furthermore, AHR allows space vehicle designers, mission planners, and operators the flexibility to determine how much time is spent in TMR and TSR. TMR mode provides faster processing at the expense of greater energy usage. TSR …

Advanced Metering Infrastructure Security With Software-Defined Network In Smart Grid, Yi-Chen Chung

Theses and Dissertations

The Advanced Metering Infrastructure (AMI) is the most important and basic element in the Smart Grid systems. Technologies grow complicated as the world becomes more convenient. Power grid, smart building, electric vehicles, and other technology need to be managed and maintained flawlessly in case of the possibility of cyberattacks to shut down all the systems and result in huge loss economically or potentially affect people's life. It is important to use communication technologies to provide many functions including facilitate bidirectional communications and remote controls. Since AMI needs to be widely deployed to each home user, power companies are required to …

Analyzing Evolution Of Rare Events Through Social Media Data, Xiaoyu Lu

Dissertations

Recently, some researchers have attempted to find a relationship between the evolution of rare events and temporal-spatial patterns of social media activities. Their studies verify that the relationship exists in both time and spatial domains. However, few of those studies can accurately deduce a time point when social media activities are most highly affected by a rare event because producing an accurate temporal pattern of social media during the evolution of a rare event is very difficult. This work expands the current studies along three directions. Firstly, we focus on the intensity of information volume and propose an innovative clustering …

Data Multiplexing In Vector Acoustic Communication: System Design And Experiments, Erjian Zhang

Dissertations

Acoustic particle velocity channels, which are vector components of the acoustic field, have been recently explored to achieve communication purposes underwater. Vector sensors and transducers that can utilize acoustic particle velocity channels have compact multichannel designs, which are perfect for compact size underwater platforms. In this dissertation, an underwater acoustic multiple-input multiple-output (MIMO) communication system featuring orthogonal frequency division multiplexing (OFDM) and frequency shift keying (FSK) modulation is discussed. By transmitting multiple independent data streams simultaneously over several channels within the same bandwidth, the proposed MIMO system increases the transmission rate. A variety of components of the system such as …

Development Of An Electrical Interface For A Lateral Field Excited Sensor System, Thomas J. Leighton

Electronic Theses and Dissertations

Sensor systems are utilized to provide critical information to an end user which may range from a physician in a heath care facility to a soldier in a battle field environment. The "heart" of the sensor system is the sensing platform, examples of which include semiconductor, piezoelectric and optical devices. The responses of these sensors must be converted into a format that the user can read and interpret. This conversion is achieved through integrating the sensing platform with an electrical interface.

The focus of this thesis is the development of the first electrical interface for Quartz Crystal Microbalance (QCM) sensors …

A Modular Approach For Modeling, Detecting, And Tracking Freezing Of Gait In Parkinson Disease Using Inertial Sensors, Prateek Gundannavar Vijay

McKelvey School of Engineering Theses & Dissertations

Parkinson disease, the second most common neurodegenerative disorder, is caused by the loss of dopaminergic subcortical neurons. Approximately 50% of people with Parkinson disease experience freezing of gait (FOG), a brief, episodic absence or marked reduction of forward progression of the feet despite the intention to walk. FOG causes falls and is resistant to medication in more than 50% of cases. FOG episodes can often be interrupted by mechanical interventions (e.g., a verbal reminder to march), but it is often not practical to apply these interventions on demand (e.g., there is not usually another person to detect an FOG episode …

Polarization Division Multiplexing For Optical Data Communications, Darko Ivanovich

McKelvey School of Engineering Theses & Dissertations

Multiple parallel channels are ubiquitous in optical communications, with spatial division multiplexing (separate physical paths) and wavelength division multiplexing (separate optical wavelengths) being the most common forms. In this research work, we investigate the viability of polarization division multiplexing, the separation of distinct parallel optical communication channels through the polarization properties of light. We investigate polarization division multiplexing based optical communication systems in five distinct parts. In the first part of the work, we define a simulation model of two or more linearly polarized optical signals (at different polarization angles) that are transmitted through a common medium (e.g., air), filtered …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

University of New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …