Digital Commons Network^™

Improvements Of Hybrid Ac/Dc House Prototype, Arden Abude

Electrical Engineering

This is an iteration from previous designs of the Hybrid AC/DC House with a systematic addition of a portable AC power supply unit. This iteration for the Hybrid AC/DC House is an innovation of independence for sustainable housing solutions. It will serve as an alternative for rural communities needing power to rely on self-sustainable microgrids rather than large-scale AC electric grids. The addition of a portable AC power supply would allow the microgrid to remove its reliance on AC power from the larger grid and would elevate the system to complete energy independence. The microgrid has DC power generated from …

Hybrid Water Pump, Dylan W. Grant, Wei Chen Yeh

Electrical Engineering

This project seeks to use multiple sources to power a water pump. We will design a system which will combine inputs from solar and wind energy production to ensure the pump will have enough power to run. This will create a system powered by clean energy and will be self-sustained once completed. This will theoretically create a more sustainable source of power for the pump than only one of the sources. Because the power sources don’t require outside inputs (aside from sun and wind), the pump can be placed in a remote area. This could be very helpful in developing …

Automatic Standby Power-Saving Power Strip, Trung Nguyen

Electrical Engineering

The Standby Power Saving Power Strip improves on common power strip functionality. The project reduces the power loss from most electrical devices’ standby power mode, while retaining the convenience of leaving the devices plugged-in. The surge protector automatically recognizes when the plugged-in devices enter standby power mode. Then, it shuts off power to that device and automatically provides power back to the plugged-in devices, when turned on.

Dc House Energy Management System, Zachary L. Eldredge, Zoe M. Hay

Electrical Engineering

In this work, a previously completed proof of concept for an Energy Management System (EMS) for the DC House project has been revised and re-implemented. The implemented design changes will improve the performance and reproducibility of the system. This new design of the EMS replaces the two-separate buck and boost DC-DC converters with a single bidirectional DC-DC converter to reduce components and improve efficiency. Analysis of the bidirectional DC-DC converter shows high efficiency especially at larger load currents. The code of the previous work was updated for smoother operation as well as to accommodate an LCD capable of displaying more …

Veloelectric: Creating A Device That Harvests Energy From Bicycles, Austin Hall, Daniel Stohr, Tj Fox

Mechanical Engineering

Long distance mountain bikers, bike-packers, and many bikers in developing countries rely on electrical devices for safety and communication. These specific groups of people operate in areas with little to no electricity, and often times have no power to sustain their devices. The purpose of this Cal Poly senior project, VeloElectric, was to design, build, and test a kinetic energy harvester for bicycles that can be used to charge common mobile devices via USB. This senior project team created a device that attaches directly to a bicycle and uses vibrations to generate energy, which in turn powers a variety of …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Technology Portal For Energy Efficient Buildings, Larry D. Hermanson, Daniel Studer, Annie Mroz

STAR Program Research Presentations

Project: Technology Portal for Energy Efficient Buildings

Date: August 2, 2012

Author: Larry Hermanson

Mentor: Daniel Studer

Cohort: Annie Mroz

Lab site: National Renewable Energy Laboratory (NREL)

Buildings account for 71% of the electricity demand and 39% of the primary energy consumption in the United States. The Commercial Buildings Group at NREL provides builders, designers and building owners accurate information to significantly improve the energy efficiency of new and existing buildings. The Technology Portal for Energy Efficient Buildings will increase the accessibility of standardized and credible energy performance data for all building systems, thereby allowing building owners to better evaluate …

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Wireless Energy Transfer, Ryan Sasur

Electrical Engineering

Phones are now an integral component in the daily lives of people. Smartphones give access to movies, internet, and even books. This versatility and increased use can also lead to a shorter battery life. A phone with video viewing capabilities will be a heavy load on the unit’s battery. With phones utilizing 3G and 4G technology, even heavier demands are placed on the battery. As technology improves even further to provide for a larger entertainment experience on the phone, this could also lead to further battery degradation if the current battery situation isn’t addressed. To have a fully operational phone …