Digital Commons Network^™

Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison

Electrical Engineering

Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …

Active Diesel Soot Measurement By Laser Opacity, Jonathan Audish, Brian Ko, Edward Ma, Travis Mcdaniel

Electrical Engineering

This project looks into understanding the concentration of soot being omitted by a diesel engine through the creation of an innovative opacity sensor. The system contains a receiver circuit implementing a photodiode, laser with wavelength of 405±10nm, and a microcontroller with analog-to-digital (A/D) converter. As the laser pulsates, the microcontroller collects and processes the data to calculate the amount of soot within the exhaust system. The opacity sensor in our tests will be used on an Isuzu 1.9 liter diesel engine. The elegant design of the system can be integrated into conventional manufacturing molding or casting processes for new exhaust …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Technology Portal For Energy Efficient Buildings, Larry D. Hermanson, Daniel Studer, Annie Mroz

STAR Program Research Presentations

Project: Technology Portal for Energy Efficient Buildings

Date: August 2, 2012

Author: Larry Hermanson

Mentor: Daniel Studer

Cohort: Annie Mroz

Lab site: National Renewable Energy Laboratory (NREL)

Buildings account for 71% of the electricity demand and 39% of the primary energy consumption in the United States. The Commercial Buildings Group at NREL provides builders, designers and building owners accurate information to significantly improve the energy efficiency of new and existing buildings. The Technology Portal for Energy Efficient Buildings will increase the accessibility of standardized and credible energy performance data for all building systems, thereby allowing building owners to better evaluate …

3.5 To 30 Mhz Automatic Antenna Impedance Matching System, William Blodgett

Electrical Engineering

Two-way communications using 3 to 30 MHz, high-frequency (HF) radio, also known as shortwave radio, provides worldwide coverage with no infrastructure required between stations. Amateur or “Ham” radio operators apply this advantage to long distance communications and to provide disaster relief communications. Optimum frequencies for long distance propagation are time-of-day variant necessitating an operating frequency range of 3 to 30 MHz. HF half wave dipole antenna length varies from 15 to 150 ft over this range. Fixed-length antenna impedance varies with frequency due to physical dimension dependent capacitance and inductance. Maximum transmitter to antenna power transfer occurs when the transmission …

The Double Pendulum: Construction And Exploration, Benjamin J. Knudson

Physics

The exploration of a nonlinear mechanical system, the Double Pendulum, a physical pendulum on the end of a physical pendulum, using analytic and experimental approaches. Also included discussion of the design and construction of the Double Pendulum apparatus to work with Vernier LabPro and LoggerPro. The apparatus outputs live data of the angles to a LoggerPro which collects and produces time evolution graphs as well as a corresponding animation lending itself to comparison with theoretical models. Normal mode frequencies are found both analytically and experimentally for the the general (real) double pendulum. Examples of both simple (periodic) and complex (chaotic) …

Design And Simulation Of Interconnected H-Bridge Inverter, Samuel Muehleck

Computer Engineering

In this project, the research, design and simulation of an interconnected H-bridge single-phase inverter was explored. The inverter design was divided into three separate sections. First, a VHDL programmed CPLD was used to generate control signals for the transistors of the inverter circuit. Second, power electronics was used to create an inverter circuit to change a DC input to a 60 Hz AC output. Lastly, additional circuits were used to link the generated control signals to the MOSFET transistors of the inverter circuit. The operation of the three components was then validated with computer simulations. Results of computer simulation demonstrate …

Design, Construction, And Evaluation Of An Automated Chicken Coop Door, Kyle Inks

BioResource and Agricultural Engineering

This senior project takes a look into the design, construction, and evaluation of an automated chicken coop door. The idea and need for such a door came from my mother Jan Inks. The parameters for the project include, low production cost, easy installation on existing coops, sleek design, automatically open at a set time in the morning, and automatically close at a set time in the evening.

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Portable Solar Powered Charging Station, Jordan Bonner

Electrical Engineering

The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.

Printed Electroluminescent Display, Christopher (Chris) James Nixon, Veronica Kopp

Electrical Engineering

Electroluminescent displays are part of an emerging technology known as printed electronics. Most identify printed electronics with purely electronic purposes such as the Radio frequency identification (RFID). Now the electronics and graphic communication industries have come together to create of new forms of products that interact with customers. Flexible, electronic circuits use functional inks and traditional printing methods such as screen printing, gravure, and inkjet. Printed electronics are perfect for low performance applications, such as displays, labels, clothing and batteries. This paper focuses on creating an interactive electroluminescent (EL) display. In selling a product, displays are important because most customers …

"Auto-Tuned" Stereo, Daniel Montes

Electrical Engineering

The purpose of this project is to determine the capability of introducing delay and gain to audio signals to synthesize a “tuned” experience. The project uses audio operational amplifiers, field effect transistors, a class D amplifier, microphones, speakers, a 32-bit microcontroller for design and testing. When implementing the MOSFET into the all pass filter, the phase delay occurs by varying the transistor resulted in minimal change in phase. MOSFETs are used as variable resistors to vary the phase change and gain. By modifying the gain the synthesized distance from each speaker can be adjusted. Varying the phase change provides the …

Ignitron Trigger Circuit, John F. O'Hara Iii

Electrical Engineering

No abstract provided.

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …

Music Driven Graphical Visualization System, Glenn Bruner

Electrical Engineering

In today’s society, we are able to enjoy listening to music on an assortment of high-tech devices such as home computers, or multimedia players, or personal audio players. A common characteristic of typical audio media players is that they lack the ability to provide visual stimulation in addition to the provided audio stimulus. Large public events, such as concerts, could be enhanced if they included visual effects in addition to audio stimulation. The goal of this project is to provide a graphical visualization that is automatically synchronized to an audio signal with a goal of enhancing the overall musical experience. …

Foce Intermodule Communications System, Roland Quiros

Electrical Engineering

Done in conjunction with Chad Kecy of the Monterey Bay Aquarium Reasearch Institute (MBARI), this project is an expansion of the Free Ocean Carbon Emission (FOCE) project. This iteration created a communications protocol between the different modules in an expandable array of PIC24-based boards.

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Pulsed Class-G Rf Amplifier System, Kevin Maulhardt, Kevin Haskett

Electrical Engineering

No abstract provided.

12 Volt Wall Outlet For The Dc House Project, Dylan Van Lant, Chenxi Zhang

Electrical Engineering

The purpose of this project is to build a DC-DC converter for the wall outlet of the DC House. This report focuses on the development of the DC -DC converter, and explains the design process as well as summarize the final results. The proposed system using the Buck or Step Down topology takes input voltage of 48V and output 12V at 100W. Results show the ability of the converter to fulfill such tasks while maintaining efficiency about 90% at all load.

All-In-One Aprs Transmitter, Justin Kenny

Electrical Engineering

The Automatic Packet Reporting System (APRS) is a digital radio system that allows transmission of data using an analog FM radio link. APRS allows position, brief messages, and other data to be distributed across a network, independent of infrastructure, making it ideal for applications such as search and rescue, asset management, and event tracking, while maintaining low cost and operating even when cellular and internet services are unavailable. This project encompasses the design, build, and test of a compact, low-cost APRS transmitter, which will include a 5W radio, GPS, and LCD-based user interface, to allow full utilization of APRS.

Lyfi, Kianoosh Salami, Justin Cotton, Elush Shirazpour

Electrical Engineering

This paper will cover the steps necessary to design, build, and manage networkable smart light switches over WiFi via a mobile application. It contains a microcontroller running a real time operating system, a WiFi module, a Java server with SQLite databasing, and a mobile phone application.

LyFi is designed to turn on/off and dim household lights while only requiring the same installation procedure as a less capable dimmer switch. Once installed and connected to a network, LyFi will self-discover and configure. The server automatically propogates a database of nodes where any mobile device running an application can receive an updated …

Inductive Metal Identification, Paul Maggi

Electrical Engineering

This project focuses on creating a device to differentiate between various types of metals via magnetic induction. Magnetic induction is used because it is both non-optical and non-contact. It achieves this by generating a varying magnetic field, which induces eddy currents in the metal. These eddy currents produce small disturbances in the surrounding magnetic field, which can be sensed with Hall Effect Sensors (HES). The primary challenge in this project was generating a sufficiently strong magnetic field to detectable disturbances. In order to achieve better results, a stronger magnetic field must be used as well as more sensitive Hall Effect …

Digital Guitar Effects Unit And Amplifier, Kevin Salvador

Electrical Engineering

This report outlines the design and implementation of a digital guitar effects unit and amplifier. The main portion of this project consisted of the digital equalizer and effects. Several commercial equalizers were researched in order to decide the typical frequency bands and average amount of bands total. Eventually 8 bands were selected. A range of approximately 20Hz-3kHz was chosen based on test data of guitar signals. Popular effects that were incorporated in this project include Distortion, Echo, Reverb, Chorus and Flanger. The digital processor chosen was a Texas Instruments c6713 floating point processor. Designs for the various filters were done …

Cascaded High Voltage Converter With Variable Control For Pulsed Electric Field Applications, Emmanuel Loza

Master's Theses

Living a sustainable lifestyle while facing increasing population and decreasing natural resources has become one of humanity’s largest challenges. Locating fossil fuels is becoming more difficult while the demand for them to power our societies is ever increasing. Instead of finding more efficient methods of extracting fossil fuels, developing technologies that create renewable substitutes for fossil fuels is now the strategy. Algae biofuel matches fossil fuel performance while also meeting the criteria for renewable energy. The focus now shifts to finding methods for commercially producing algae biofuel. Therefore, the objective of this thesis is to develop a system that provides …

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

Linear Power-Efficient Rf Amplifier With Partial Positive Feedback, Matthew E. King

Master's Theses

Over the last decade, the number of mobile wireless devices on the market has increased substantially. New “multi-carrier” modulation schemes, such as OFDM, WCDMA, and WiMAX, have been developed to accommodate the increasing number of wireless subscribers and the demand for faster data rates within the limited commercial frequency spectrum. These complex modulation schemes create signals with high peak-to-average power ratios (PAPR), exhibiting rapid changes in the signal magnitude. To accommodate these high-PAPR signals, RF power amplifiers in mobile devices must operate under backed-off gain conditions, resulting in poor power efficiency. Various efficiency-enhancement solutions have been realized for backed-off devices …

Efficiency Performance Improvement Using Parallel Dc-Dc Converters With A Digital Controller, Daniel Forbes

Master's Theses

A system to improve efficiency performance of a DC-DC converter is simulated and built. The proposed system combines multiple DC-DC converters in parallel and implements a digital control scheme and load-share controller. A model of the system is developed in MATLAB Simulink and the model demonstrates the improved converter’s efficiency particularly at low load conditions. This simulation is then designed into a hardware system running three DC-DC converters in parallel, controlled by a microcontroller and a load-share controller. The hardware also confirms the simulation results, although some hardware refinements are evident as simulation results are superior. The system is designed …

Robot X, Alan Truong, Alex Haag

Computer Engineering

The following report outlines the design decisions behind Robot X for the 2012 Cal Poly Roborodentia competition held annually during Open House. This investigation includes detailed overview of Robot X's sensory system, driving system, conveyor belt system, and can compartment system. In addition, basic hardware and software design are explored.

Kreative Outlets, Travis Crist, Steve Clark, Jason Peressini

Computer Engineering

With the widespread use of smart phones and the advancement of WiFi technologies, people now have the Internet at their fingertips at all times. Home automation and control has the possibility of becoming the next big technology that can utilize the abundant availability of the Internet. This paper documents the findings and results of a project aimed at developing the infrastructure needed for a home automation system that is accessible anywhere. We implemented a system that utilized a web enabled ethernet connection and RF wireless technology to control AC outlets and provide the user with feedback information about the status …