Digital Commons Network^™

Additive Manufacturing Of Soil Using Bio-Cementation, Christina Childress

Graduate Theses and Dissertations

Microbially Induced Calcite Precipitation (MICP) is an emerging soil treatment technique that is proven to increase strength, decrease erosion, reduce liquefaction risk, enhance slope stability, decrease compressibility, decrease swelling potential, and overall create a more competent soil. The benefits and applications of MICP are broad, and this research seeks to broaden them further by developing a single-phase additive manufacturing application with no treatment time delay. This is done by analyzing layering behaviors of five USCS soil classifications (100 % Ottawa sand, sand clay mixtures, and 100% lean clay) which provides insight into process variables such as the solution volume and …

An Investigation Of The Flexural Strength And Toughness Of Hybrid Plain And Fiber Reinforced Concrete For Pavement Applications, Wesley Keys

Graduate Theses and Dissertations

For decades, many solutions have been evaluated to combat cracking in concrete pavements. The study presented in this paper evaluates and compares the flexural performance under a third point loading configuration of plain concrete (PC) beams, fully fiber reinforced concrete (FRC) beams, and hybrid PC and FRC beams, with a top PC and bottom FRC layer. The purpose of this hybrid approach was to provide FRC in only half the section, saving cost, while providing a PC surface layer that is easier to finish. All PC top layers were applied at an age of 7-days, considered a reasonable time for …

Retrospective Analysis Of Impacts Of Highway Bypass And Widening Projects, Sanjeev Bhurtyal

Graduate Theses and Dissertations

Community members often worry that highway projects may have negative impacts on their local economies. This is typical for highway bypass and widening projects in small cities (population less than 50,000). It is a challenge for planners to balance public concerns of economic decline with desired project outcomes of mobility and safety. Much of this challenge stems from a lack of information on post-project outcomes related to economic and safety impacts of new construction projects. Thus, there is a need for an evidence-based framework to help planners with the decision-making process and better inform the community on potential outcomes. This …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Factors Influencing The Usage Of Shared E-Scooters : A Case Study Of Chicago, Farzana Mehzabin Tuli

Graduate Theses and Dissertations

The rapid popularity growth of shared e-scooters creates the necessity of understanding the determinants of shared e-scooter usage. This thesis estimates the impacts of temporal variables (weather data, weekday/weekend, and gasoline prices) and time-invariant variables (socio-demographic, built environment, and neighborhood characteristics) on the shared e-scooter demand by using four months (June 2019- October 2019) period of data from the shared e-scooter pilot program in Chicago. The study employs a random-effects negative binomial (RENB) model that effectively models shared e-scooter trip origin and destination count data with over-dispersion while capturing serial autocorrelation in the data. Results of temporal variables indicate that …

Improve The Prediction Of Camber, Deflection, And Prestress Losses In Precast, Prestressed Concrete Bridge Girders, Ahmed Ali Hussein Al Mohammedi

Graduate Theses and Dissertations

Many precast, prestressed concrete girders have camber less or higher than the design values. This discrepancy between the design and the actual camber creates construction problems when installing the cast-in-place concrete deck. The objective of this research was to improve the accuracy of estimating long-term camber, deflection, and prestress losses of precast, prestressed concrete girders.

The experimental program consisted of measuring concrete properties and performing field measurements of camber, deflection, and prestress losses for girders in Arkansas. The investigation involved testing nine full-scale girders from two prestressed concrete plants that regularly supply concrete girders to bridge projects in Arkansas. The …

Formation Of Reactive Nitrogen Species During Dichloramine Decay And Their Impact On N Nitrosodimethylamine Formation Under Drinking Water Conditions, Huong Thu Pham

Graduate Theses and Dissertations

NDMA occurrence and formation pathways in drinking water systems are reviewed and NDMA yields are compared on the basis of disinfectant type, water chemistry, and precursor category. In chloramination, despite monochloramine being the predominant species between pH 7-9, evidence suggests that dichloramine is the primary species involved in NDMA formation. This is somewhat confounding as NDMA yields are maximal at pH 9, yet at pH 9 dichloramine decays faster than it forms and hence is present at trace levels; additionally, the proposed mechanism involves a spin-forbidden incorporation of dissolved oxygen as a triplet, which is presumably kinetically slow. This review …

Evapotranspiration In Mid-South Rice Production, Colby Wade Reavis

Graduate Theses and Dissertations

Rice provides much needed sustenance to a large portion of the global population, particularly in the developing world. With stress placed on food production systems under the reality of climate change and an increasing global population, rice production systems require solutions to a number of issues, including a limited water supply. As producers explore new strategies for conserving local water resources to continue to maintain yields, new irrigation strategies and technologies are being developed and validated for use at commercial production scales. Alternate wetting and drying (AWD) is an irrigation practice that provides water savings through the capture of rainfall …

Identification Of Phosphorous Loading Point Source Facilities To 303(D) Listed Nutrient Impaired Waters Through Watershed Delineation Using Arcgis For Life Cycle Assessment Applications, John Zimmerman

Chemical Engineering Undergraduate Honors Theses

The work done for this project is part of a larger “life cycle assessment (LCA) of novel electrochemical phosphorus recovery technology at the wastewater treatment plant and U.S. watershed scales” (Morrissey 2019). The goal of that LCA is to determine “environmental impacts of implementing electrochemical struvite recovery at the wastewater treatment plant, U.S watershed, and global scales” (Morrissey 2019). This project’s goal is to identify locations deemed more sensitive to eutrophication impacts. The results will be used as part of the life cycle inventory (LCI) accounting for geographically explicit phosphorus flows. The waters identified as impaired were sourced from the …

Relating The Dongre Workability Test To Cold In-Place Recycled Asphalt Pavements, Gus Williams

Civil Engineering Undergraduate Honors Theses

The Dongre Workability Test (DWT) is a test for determining an asphalt pavement’s relative workability from the stress-strain curve of a sample. While the DWT has seen favorable results with warm mix and hot mix asphalt, Casillas and Braham (2020) attempted to apply this test to cold in-place recycled (CIR) asphalt pavements with limited results. This paper looked at the process of reexamining the DWT method to more favorable results with CIR samples. Phase 1 consisted of defining ten possible metrics from the stress-strain curve and applying them to samples with three different curing conditions. From these preliminary results, the …

Data-Driven Methods To Address Truck Parking Shortages For Long-Haul Commercial Truck Drivers, Sharif Mahmud

Graduate Theses and Dissertations

Truck parking is a critical concern for both the trucking industry and the truck drivers. Long-haul commercial truck drivers rely on safe and adequate parking to support interstate commerce, which has become a challenge due to parking shortages. The recent electronic logging device (ELD) mandate, forcing a strict compliance to hours of service (HOS) regulations, are leading to higher demand for parking. A number of federal, regional, and local studies reveal that truck activity will increase and truck parking demand will outpace parking supply in the coming years. Such parking shortages likely disrupt freight flows and pose risks to truck …

Mitigating Calcium Oxychloride Damage In Cementitious Paste And Concrete Utilizing Supplementary Cementitious Materials, Casey Jones

Graduate Theses and Dissertations

It is understood among engineers in the United States (U.S.) that improvement is needed throughout the transportation infrastructure. In the 2021 Infrastructure Report Card produced by the American Society of Civil Engineers, the roadways of this nation merit a D. This leaves room for improvement in order to provide durable pavements throughout this nation. Areas with significant winter weather may have exacerbated effects in decreased roadway longevity due to freezing/thawing cycles and the use of chemical deicers to mitigate gelid roadway conditions. Much research focuses on surface scaling and reinforcement corrosion using these materials; however, joint deterioration, due to chemical …

Applications Of Masw And Mhvsr Techniques For Infrastructure Evaluation With A Focus On The Effects Of Different Transformation Techniques And Near-Field Effects On Derived Dispersion Data, Salman Rahimi

Graduate Theses and Dissertations

This dissertation is aimed at understanding two aspects of active surface wave methods to improve the accuracy and reliability of this method. These include (1) the performance of four common wavefield transformation methods for the multichannel analysis of surface wave (MASW) data processing and (2) near-field effects. Toward this end, extensive field measurements were conducted considering different factors affecting these two topics. The MASW and microtremor horizontal to vertical spectral ratio (MHVSR) were then employed to examine their efficiency for infrastructure health monitoring.

Regarding the performance of the four common transformation techniques, it was observed that for sites with a …

Design And Validation Of A High-Power, High Density All Silicon Carbide Three-Level Inverter, Zhongjing Wang

Graduate Theses and Dissertations

Transportation electrification is clearly the road toward the future. Compared to internal combustion engine, the electrified vehicle has less carbon-dioxide emission, less maintenance costs and less operation costs. It also offers higher efficiency and safety margin. More importantly, it relieves human’s dependence on conventional fossil energy. In the electrification progress, the revolution of electric traction drive systems is one of the most important milestone. The traction system should keep high efficiency to avoid performance reduction. Moreover, the motor drive should be designed within limited space without sacrificing output power rating. Based on the road map from US Drive Electrical and …

Signal Processing And Data Analysis For Real-Time Intermodal Freight Classification Through A Multimodal Sensor System., Enrique J. Sanchez Headley

Graduate Theses and Dissertations

Identifying freight patterns in transit is a common need among commercial and municipal entities. For example, the allocation of resources among Departments of Transportation is often predicated on an understanding of freight patterns along major highways. There exist multiple sensor systems to detect and count vehicles at areas of interest. Many of these sensors are limited in their ability to detect more specific features of vehicles in traffic or are unable to perform well in adverse weather conditions. Despite this limitation, to date there is little comparative analysis among Laser Imaging and Detection and Ranging (LIDAR) sensors for freight detection …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

A Machine Learning Approach To Understanding Emerging Markets, Namita Balani

Graduate Theses and Dissertations

Logistic providers have learned to efficiently serve their existing customer bases with optimized routes and transportation resource allocation. The problem arises when there is potential for logistics growth in an emerging market with no previous data. The purpose of this work is to use industry data for previously known and well-documented markets to apply data analytic techniques such as machine learning to investigate the uncertainty in a new market. The thesis looks into machine learning techniques to predict miles per stop given historical data. It mainly focuses on Random Forest Regression Analysis, but concludes that additional techniques, such as Polynomial …

Shallow 3d Shear Wave Velocity Model And Revised Site Period Prediction Map For The Mexico City Basin, Rendon Martin Rieth

Graduate Theses and Dissertations

The goal of this study was to revise the existing site period prediction map and to develop a shallow 3D shear wave velocity model of the Mexico City Basin. To accomplish this goal, an extensive literature review was performed to compile as much pertinent shear wave velocity and site period data for the region. In total, 75 sites were used to revise the site period prediction map and 40 sites were used to develop the shear wave velocity model. The 2004 Complementary Technical Standards of Mexico site period prediction map was adjusted with new site period measurements across the basin …

Development Of An Ultraviolet Absorbance Assay To Estimate Air Entrainer Dosing For Concrete Containing Fly Ash, James Spencer

Graduate Theses and Dissertations

Fly ash is a coal combustion byproduct that can be used as a supplementary cementitious material (SCM) in concrete, offering benefits such as increased workability, durability, and strength. Fly ash can be used as a partial replacement to cement, reducing concrete productions costs and decreasing disposal in landfills. However, variability of fly ash properties (e.g., carbon content, adsorption site density) confounds estimates of the air entraining admixture (AEA) dose needed to achieve a specified air content in concrete. Air entrainment is needed to improve freeze-thaw resistance and limit concrete cracking. The foam index (FI) test is currently used to estimate …

Comparison Of The Resistance Of Belitic Calcium Sulfoaluminate Cement And Portland Cement To Sulfate Attack And Sulfuric Acid, Rilye Dillard

Graduate Theses and Dissertations

Microbially induced corrosion (MIC) is a fairly common concrete deterioration mechanism with many negative effects. MIC is a complex chemical and biological process that occurs in sewage systems and is nearly impossible to replicate in a laboratory setting. For this study, sulfate and sulfuric acid attack on concrete were studied to mimic two stages of the MIC process. The ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution and a modified ASTM C1012 accelerated method were used to compare the sulfate resistance of belitic calcium sulfoaluminate (BCSA) cement, portland cement (PC), and PC-fly …

Experimental Design And Preliminary Testing For Skewed Special Moment Frame Prequalification, Sara Alimirzaei

Graduate Theses and Dissertations

Special moment frames having specially detailed connections are common in high seismic regions, providing architectural flexibility for passageways and views without brace obstructions. In situations where the building framing layout requires deviation from typical rectangular framing, skew in the moment frame connections may be required. Currently, the AISC prequalified connections only include testing of orthogonal moment frame connections and it is unclear whether the existing design methods can accommodate skew at the beam-to- column connections. To investigate the effect of out-of-plane skew on the performance of reduced beam section special moment frame connections, an experimental test is designed and a …

When It Rains, It Pours: A Case Study Of Spatio-Temporal Variations In High-Intensity Precipitation Events In Arkansas, Deanna Mantooth-Hendrix

Graduate Theses and Dissertations

Climate change is having an impact on weather systems and ecosystems worldwide. Glaciers are receding, oceans are acidifying, hurricanes are stronger, and extreme precipitation is increasing in frequency. Even with the wealth of data and knowledge about the threat of climate change, some places are slow to adapt because they think that the impact to their ecosystem will not be severe. The goal of this project was to determine if climate change is having an impact on extreme precipitation in the top urban areas of Arkansas. The major concern with an increase in extreme events in urban areas is flooding. …

Analysis Of Shear-Strength In Weathered Shale Strata Along A Highway Slope Failure Site In Northwest Arkansas, Olivia Overton

Civil Engineering Undergraduate Honors Theses

Slope failures cost millions of dollars per year to repair and can be deadly. Accurate modeling of slope conditions, including soil parameters, water table locations, and depth to bedrock, are essential to determining the overall stability of a slope. This project is a continuation of the work completed in 2019 by a former University of Arkansas researcher, Vanessa LeBow. LeBow RocScience used Slide2 modeling software to model two highway embankment slopes in Northwest Arkansas that experienced slope movement to determine whether increased use of geophysical data could increase the accuracy of slope stability models. A parametric study of shear strengths …

Low Impact Development: Low-Maintenance Design To Encourage Residential Adoption Of Sustainable Systems, Haley Ellis

Biological and Agricultural Engineering Undergraduate Honors Theses

Residential adoption of low-impact development (LID) technology can positively impact downstream watershed hydrology by reducing total volumetric discharge from the residential site. This reduction can provide economic, environmental, and social benefits for the residents as well as the community at large. Additionally, homeowners are often affected by stormwater related issues, like flooding or washout, that could be easily mitigated with a sustainably engineered LID structure or network. Engineering for sustainability often includes the blending of several objectives to provide greater overall benefit. This thesis compares the outflow characteristics of three low-maintenance residential LID design scenarios differing in rain garden soil …

Improving Logistics Efficiency Through Collaborative Truck Routing, Patrick Dougherty

Industrial Engineering Undergraduate Honors Theses

The logistics industry is among the world’s largest and most essential. Specifically, trucking is a massive component of the modern logistics system. In 2012, truck transportation carried 68% of all freight tonnage in the U.S. However, trucking currently faces significant problems with efficiency and sustainability. Of all miles driven by trucks yearly in the U.S., 25% are driven with empty loads and 36% are driven with underutilized loads. In addition to this economic inefficiency, the industry faces social and environmental challenges. Driver turnover rates are near 100%, and trucking accounts for a significant level of greenhouse gas emissions. One potential …