Electrical and Electronics Commons^™

Call For Papers Of Iceea10, Toufik Rekioua Pr

REKIOUA Djamila Dr

We are pleased to announce that we are organizing an international conference on electrical engineering, electronics and Automatic (ICEEA'10) which will take place in Bejaia (Algeria) on 2-3 November 2010 (see call for papers)

Development Of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach, Bagiyo Suwasono, Sjarief Widjaja, Achmad Zubaydi, Zaed Yuliadi, I Nyoman Budiantara

Makara Journal of Technology

Development of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach. Ability of production processes associated with state-of-the-art technology, which allows the shipbuilding, is customized with modern equipment. It will give impact to level of productivity and competitiveness. This study proposes a nonparametric regression cubic spline approach with 1 knot, 2 knots, and 3 knots. The application programs Tibco Spotfire S+ showed that a cubic spline with 2 knots (4.25 and 4.50) gave the best result with the value of GCV = 56.21556, and R2 = 94.03%.Estimation result of cubic spline with 2 knots for the PT. Batamec shipyard …

Wimax Implementation As Existing Hotspot Network Backhaul In Jakarta, Djamhari Sirat, Muhamad Asvial, Luther B. Marpaung

Makara Journal of Technology

WiMAX Implementation as Existing Hotspot Network Backhaul in Jakarta The development of Broadband Wireless Access (BWA), such as WiMAX, as a global standard for data transmission media has been used by high speed internet access provider. WiMAX application which supported by capabilities of interoperability, flexibility and commercial aspect make the internet services become more efficient, cheaper and easier to the customer. This phenomenon should be responded by ISPs. Based on technical and financial aspect in deciding the implementation of Wireless Network with WiMAX technology as a substitute, this research will observe and analyze the projection of WiMAX technology implementation as …

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin

Makara Journal of Technology

High Pressure Adsorption Isotherm of CO2 on Activated Carbon using Volumetric Method. Adsorption system is ones of the most effective methods for CO2 separating with other substances that produced from the burning of fossil fuels. In the design for that application, beside of characteristics of porous material (adsorbent) data, CO2 adsorption data on the adsorbent (kinetic and thermodynamic) are also needed. The aim of this research is resulting isothermal adsorption data at pressures up to 3.5 MPa by indirect methods (volumetric method) at isothermal temperature of 300, 308, 318 and 338 K. Adsorbent that used in this research is activated …

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati

Makara Journal of Technology

Diafiltration by means of the ultrafiltration system of probiotic fermented Mung beans (Phaseolus radiatus L.) concentrate has been performed to reduce or eliminate salts and smaller impurities than the nominal cut-off of the membrane of 20,000 nominal weight cut-off (NWCO). These processes have been conducted as an attempt in order to get a probiotic product with organoleptic acceptability, composition, and the optimal total lactic acid bacteria (LAB) counts because the presence of salts will affect on the viability of LAB and the cell lysis of LAB and limit its utility in food products. Concentrate of probiotic mung beans was prepared …

Hydrogen Absorption Induced Slow Crack Growth In Austenitic Stainless Steels For Petrochemical Pressure Vessel Industries, Ronnie Higuchi Rusli

Makara Journal of Technology

Type 304L and type 309 austenitic stainless steels were tested either by exposed to gaseous hydrogen or undergoing polarized cathodic charging. Slow crack growth by straining was observed in type 304L, and the formation of α‘ martensite was indicated to be precursor for such cracking. Gross plastic deformation was observed at the tip of the notch, and a single crack grew slowly from this region in a direction approximately perpendicular to the tensile axis. Martensite formation is not a necessary condition for hydrogen embrittlement in the austenitic phase.

The Impact Of Quality Management Systems During A Pebble Bed Modular Reactor Project : A Case Study, Lwandiso Zamxaka

Lwandiso L Zamxaka

In the nuclear industry, Quality Management Systems are extremely important,especially if one wishes to improve public acceptance of radioactive solutions.There is normally minimum communication between the public and scientists,especially in nuclear science. People are not comfortable with nuclear technology,based on the past history of the Chernobyl catastrophe. Consequently, it is difficult to discuss important and sensitive issues like disposing of nuclear waste. Quality Management Systems can improve public confidence and communication. Integrated Management Systems in the project planning stage of the project can be a proactive step towards preventing unnecessary delays and costs. There is a perception that quality is …

A Single-Chip Ultra-Wideband Based Wireless Sensor Network Node, Nathan R. Schemm

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

This dissertation presents the design of a next-generation wireless sensor network node. The node incorporates many new and innovative technologies such as an ultra-wideband radio which allows very low-energy communication, a low-power radiation detection front end, and an efficient implementation of dynamic voltage scaling which improves the energy efficiency of the integrated processor. The complete design is integrated on a single chip for maximum power savings and minimal size.

The ultra-wideband transceiver includes many novel techniques to produce a receiver with low power consumption and fast and accurate packet acquisition and reception. These include the use of a standard symmetric …

Genetic Algorithm Based Optim-Al Sizing Of Pv-Diesel-Battery System Considering Co2 Emission And Reliability, Dr. Adel A. Elbaset, Heri Suryoatmojo, Prof. Dr. Takashi Hiyama

Dr. Adel A. Elbaset

The reliability system concern and CO2 emission reduction are still the main targets of optimization problem in the hybrid generation system components. This pa- per utilizes Genetic Algorithm (GA) method to determine the optimal capacities of PV system, battery bank and diesel generator (DG) unit according to the minimum cost ob- jective functions that relate to these two factors. In this study, the cost objective function includes the annual capital cost (ACC), annual operation maintenance cost (AOM), an- nual replacement cost (ARC), annual fuel cost (AFC), annual emission cost (AEC) and annual customer damage cost (ADC). The proposed method has …

Doping Dependence Of Electronic And Mechanical Properties Of Gase1−XTeX And Ga1−XInXSe From First Principles, Zs. Rak, S. D. Mahanti, K. C. Mandal, N. C. Fernelius

Faculty Publications

No abstract provided.

Reconfigurable 4-Frequency Cmos Oscillator Based On Aln Contour-Mode Mems Resonators, Matteo Rinaldi, Chengjie Zuo, Jan Van Der Spiegel, Gianluca Piazza

Chengjie Zuo

This paper reports on the first demonstration of a reconfigurable Complementary Metal Oxide Semiconductor (CMOS) oscillator based on MicroElectroMechanical System (MEMS) resonators operating at 4 different frequencies (268, 483, 690 and 785 MHz). A bank of multi-frequency switchable AlN Contour-Mode MEMS resonators (CMRs) were connected to a single CMOS oscillator circuit that can be configured to selectively operate in 4 different states with distinct oscillation frequencies. The phase noise (PN) of the reconfigurable oscillator was measured for each of the 4 different frequencies of operation showing values between -94 and -70 dBc/Hz at 1 KHz offset and PN floor values …

Finding The Exact Maximum Impedance Resonant Frequency Of A Practical Parallel Resonant Circuit Without Calculus, Kenneth V. Cartwright, Elton Joseph, Edit J. Kaminsky

Electrical Engineering Faculty Publications

A practical parallel resonant circuit has a resistor in series

with an inductor, and that combination is in parallel with a

capacitor. For such a circuit, it is well known that there are

two possible definitions for the resonant frequency: (i) the

resonant frequency , p f which is the frequency at which the

phase of the total impedance is zero, and (ii) the resonant

frequency m f , which is the frequency that achieves maximum

magnitude of the total impedance. To find the latter

traditionally requires calculus. However, in this paper, the

authors show how m f

can be …

Microstrip-Fed Wideband Circularly Polarized Printed Antenna, Xiulong Bao, Max Ammann, Patrick Mcevoy

Articles

A wideband circularly-polarized printed antenna is proposed, which employs an asymmetrical dipole and a slit in the ground plane which are fed by an L-shaped microstrip feedline using a via. The proposed antenna geometry is arranged so that the orthogonal surface currents, which are generated in the dipole, feedline and ground plane, have the appropriate phase to provide circular polarization. A parametric study of the key parameters is made and the mechanism for circular polarization is described. The measured results show that the impedance bandwidth is approximately 1.34 GHz (2.45 GHz to 3.79 GHz) and the 3 dB axial ratio …

Reconfigurable 4-Frequency Cmos Oscillator Based On Aln Contour-Mode Mems Resonators, Matteo Rinaldi, Chengjie Zuo, Jan Van Der Spiegel, Gianluca Piazza

Matteo Rinaldi

This paper reports on the first demonstration of a reconfigurable Complementary Metal Oxide Semiconductor (CMOS) oscillator based on MicroElectroMechanical System (MEMS) resonators operating at 4 different frequencies (268, 483, 690 and 785 MHz). A bank of multi-frequency switchable AlN Contour-Mode MEMS resonators (CMRs) were connected to a single CMOS oscillator circuit that can be configured to selectively operate in 4 different states with distinct oscillation frequencies. The phase noise (PN) of the reconfigurable oscillator was measured for each of the 4 different frequencies of operation showing values between -94 and -70 dBc/Hz at 1 KHz offset and PN floor values …

Ultra-Thin-Film Aln Contour-Mode Resonators For Sensing Applications, Matteo Rinaldi, Chiara Zuniga, Gianluca Piazza

Matteo Rinaldi

This paper reports on the design and experimental verification of a new class of ultra-thin-film (250 nm) aluminum nitride (AlN) microelectromechanical system (MEMS) contour mode resonators (CMRs) suitable for the fabrication of ultra-sensitive gravimetric sensors. The device thickness was opportunely scaled in order to increase the mass sensitivity, while keeping a constant frequency of operation. In this first demonstration the resonance frequency of the device was set to 178 MHz and a mass sensitivity as high as 38.96 KHz⋅μm2/fg was attained. This device demonstrates the unique capability of the CMR-S technology to decouple resonance frequency from mass sensitivity.

Ghz Range Nanoscaled Aln Contour-Mode Resonant Sensors (Cmr-S) With Self-Sustained Cmos Oscillator, Matteo Rinaldi, Chiara Zuniga, Chengjie Zuo, Gianluca Piazza

Matteo Rinaldi

This paper reports on the design and experimental verification of a new class of nanoscaled AlN Contour-Mode Resonant Sensors (CMR-S) for the detection of volatile organic chemicals (VOC) operating at frequencies above 1 GHz and connected to a chip-based CMOS oscillator circuit for direct frequency read-out. This work shows that by scaling the CMR-S to 250 nm in thickness and by operating at high frequencies (1 GHz) a limit of detection of ~35 zg/µm2 and a fast response time (<1 >ms) can be attained. In addition, the capability to detect concentrations of volatile organic compounds such as 2,6 dinitroluene (DNT) …

Ultra-Thin Super High Frequency Two-Port Aln Contour-Mode Resonators And Filters, Matteo Rinaldi, Chiara Zuniga, Chnegjie Zuo, Gianluca Piazza

Matteo Rinaldi

This paper reports on the demonstration of a new class of ultra-thin (250 nm thick) super high frequency (SHF) AlN piezoelectric two-port resonators and filters. A thickness field excitation scheme was employed to excite a higher order contour extensional mode of vibration in an AlN nano plate (250 nm thick) above 3 GHz and synthesize a 1.96 GHz narrow-bandwidth channel-select filter. The devices of this work are able to operate over a frequency range from 1.9 to 3.5 GHz and are employed to synthesize the highest frequency MEMS filter based on electrically self-coupled AlN contour-mode resonators. Very narrow bandwidth (~ …

Improving Range Estimation Of A 3d Flash Ladar Via Blind Deconvolution, Jason R. Mcmahon

Theses and Dissertations

The purpose of this research effort is to improve and characterize range estimation in a three-dimensional FLASH LAser Detection And Ranging (3D FLASH LADAR) by investigating spatial dimension blurring effects. The myriad of emerging applications for 3D FLASH LADAR both as primary and supplemental sensor necessitate superior performance including accurate range estimates. Along with range information, this sensor also provides an imaging or laser vision capability. Consequently, accurate range estimates would also greatly aid in image quality of a target or remote scene under interrogation. Unlike previous efforts, this research accounts for pixel coupling by defining the range image mathematical …

The Application Of Multi Frequency Resonant Controllers In In A Dfig To Improve Performance By Reducing Unwanted Power And Torque Pulsations And Reducing Current Harmonics., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

The paper describes a method to control the rotor-side and grid side converters in a DFIG when subjected to the effects of network voltage unbalance conditions. Multi Frequency Resonant Controllers are incorporated into the grid side and rotor side converters to assist in the control functions. The Resonant Controllers are tuned to twice the network frequency to assist in the control of power and torque pulsations and to three times the network frequency to assist in the control of the generated third harmonic currents. A DFIG model is implemented in Matlab/Simulink and simulations show the reduction in power and torque …

The Application Of Multi Frequency Resonant Controllers In In A Dfig To Improve Performance By Reducing Unwanted Power And Torque Pulsations And Reducing Current Harmonics., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

The paper describes a method to control the rotor-side and grid side converters in a DFIG when subjected to the effects of network voltage unbalance conditions. Multi Frequency Resonant Controllers are incorporated into the grid side and rotor side converters to assist in the control functions. The Resonant Controllers are tuned to twice the network frequency to assist in the control of power and torque pulsations and to three times the network frequency to assist in the control of the generated third harmonic currents. A DFIG model is implemented in Matlab/Simulink and simulations show the reduction in power and torque …