Structural Engineering Commons^™

Strengthening Of Corroded Steel Structures Using Cfrp – An Experimental Review, Ghada El-Mahdy Ph.D., P.Eng, Abdallah H. Yassin, Abdel El Rahman Khaled

Civil Engineering

Fibre reinforced polymers (FRP) have been widely used to strengthen reinforced concrete structures, however, nowadays their use to strengthen steel structures is under investigation. In particular, the need to strengthen corroded steel structures found in aggressive environments, such as marine environments, which have undergone a reduction in cross-sectional area and hence a reduction in their load-carrying capacity is in need of studying. The main problems that arise when using carbon fibre reinforced polymer (CFRP) sheets to strengthen steel structures is the weakness in the interfacial bond between the CFRP and the steel surface, the thinness of CFRP sheet, and the …

Sway And No-Sway Behaviour Of Pitched Roof Portal Frames Composed Of Cold-Formed Steel Sections, Ghada El-Mahdy Ph.D, P.Eng., Maged Tawfick Hanna Ph.D

Civil Engineering

Cold-formed sections buckle locally and distortionally in combination with overall buckling of the member. When these sections are incorporated into a portal frame structure, this combination of buckling modes affects the overall buckling behaviour of the portal frame. The objective of this paper is to study the effect of local and distortional buckling on the overall behaviour of portal frames. The portal frames studied have a span of 10 m and an eave height of 3 m with a roof pitch of 1:10. Two frames are studied the first with one intermediate interconnector at the midpoints of the column and …

Evaluation Of A Novel Remote Displacement Sensor Prototype Using Video And Laser-Based Technology For Civil Infrastructure Applications, Nicholas J. Brown

Civil and Environmental Engineering Master's Project Reports

Deflection measurements on structures, especially with regards to long-term monitoring, continues to be a challenge with current sensor technologies. Material degradation and changes in the mechanical properties due to aging (for example, creep and shrinkage in concrete bridges) directly impact the deflections exhibited by a structure. In this article we introduce and discuss the evaluation of a novel laser and video-based displacement sensor prototype to monitor displacements and rotations in structures remotely. The sensor is both inexpensive, using off-the shelf components, but also accurate and practical for situations that do not allow the use of conventional displacement sensors, which require …

Retrofit Of Corroded Corrugated Metal Culverts Using Gfrp Slip-Liner, Rahulreddy Chennareddy

Civil Engineering ETDs

Culverts are water conveyance structures, typically used to allow water flow and maintain a balance between the flow streams without interrupting structures such as highways and bridges. Corrugated metal pipes (CMPs) have been used as culverts in North America since the 1950s because of their low cost and simple construction method. Today, the corrosion of CMPs is a major problem faced by all U.S. Departments of Transportation. There is an urgent need to provide an efficient solution, one that is corrosion-resistant, to retrofit thousands of corroded CMPs across the country. High specific strength, high strength to weight ratio, corrosion resistance, …

Application Of Bayesian Networks To Integrity Management Of Energy Pipelines, Wei Xiang

Electronic Thesis and Dissertation Repository

Metal-loss corrosion and third-party damage (TPD) are the leading threats to the integrity of buried oil and natural gas pipelines. This thesis employs Bayesian networks (BNs) and non-parametric Bayesian networks (NPBNs) to deal with four issues with regard to the reliability-based management program of corrosion and TPD. The first study integrates the quantification of measurement errors of the ILI tools, corrosion growth modeling and reliability analysis in a single dynamic Bayesian network (DBN) model, and employs the parameter learning technique to learn the parameters of the DBN model from the ILI-reported and filed-measured corrosion depths. The second study develops the …

Forensic Investigation Of Building Failure – The Harbour Cay Condominium Disaster, John Airis

Publications and Research

When a building suffers collapse, the U.S. Occupational Safety and Health Administration (OSHA) is tasked with conducting an investigation into the cause. Often OSHA will request technical assistance from the National Institute for Standards and Technology to assist in the forensic technical aspects determining a most probable cause. This forensic effort entails many actions. The Harbour Cay Condominium disaster occurred on March 28, 1981 in Cocoa Beach, Florida. It was a total collapse of a five story reinforced concrete structure during the last stage of roof construction, resulting in 11 deaths and 24 injuries. The investigation report revealed structural design …

Diffusion And Uniformity Of Recycled Asphalt In Pavements, Baoshan Huang

Abbett Distinguished Seminar Series

Asphalt pavements covers over 93 percent of the paved roads in the United States. The use of recycled asphalt into pavement maintenance and construction has been a common practice. However the lack of understanding of the interaction between recycled and virgin asphalt poses a change on the efficient use of recycled asphalt, and often causes pavement premature failures. The present study addressed some fundamental aspects associated with the beneficial use of recycled asphalt into asphalt paving mixtures: 1) how much recycled asphalt can be mobilized into a uniform asphalt coating in the mixture? and 2) will the mobilized old asphalt …

Simulation Training And Route Optimization For Bridge Inspection, Sushil Louis

INSPIRE Archived Webinars

Since the 1970s, simulation training has developed opera­tional trainers for a variety of complex systems from pilot flight simulations to cultural awareness training simulations. When connected to the real world, such simulation training interfaces can drive real vehicles and systems. We have been building a Simulation Training And Control System (STACS) for autonomous bridge inspection that uses a simulated world to train inspectors to control a heterogeneous group of robots. The objective is that, once trained, inspectors can use the same STACS interface used in training to control multiple real robots simultaneously during a bridge inspection task. We first built …

Static Analysis Of Structural Members, Amani Calderon, Alexis Villalona, Farhad Alinaghizadeh

Publications and Research

This research is devoted to statics analysis of structural members under mechanical loads. Static analysis of beams under uniform transverse mechanical loads is presented. The beams are supported by simply supported boundary condition at both sides. The equilibrium equation of the beams is obtained and solved using analytical method and numerical method. The numerical method employed in this work is generalized differential quadrature (GDQ) method. The type of differential quadrature method used for numerical solution is the polynomial-based GDQ method. The differential equation is discretized into algebraic equations based on the GDQ technique. The algebraic equations are then solved to …

Static Analysis Of Circular Plates Under Mechanical Loads, Harpreet Lalia

Publications and Research

In this research statics analysis of circular plates is performed using SolidWorks.

Circular plates with different material properties, thickness to radius ratios, and boundary conditions under mechanical loads are modeled and analyzed in SolidWorks.

The results are obtained for deflections of circular plates under uniform and point loads.

A three-dimensional (3D) model of circular plates is first created in SolidWorks. Then the material properties, mechanical loads and boundary conditions are defined for the plate.

It is found deflection of plates is depended on magnitude of mechanical loads, geometrical parameters, boundary conditions and material properties. Responses of SolidWorks for deflections of …

Influence Of Nh4f In Dextran Based Biopolymer Electrolytes: Conductivity And Electrical Analysis, Muhamad Hafiz Hamsan, Mohd Fakhrul Zamani Kadir, Shujahadeen Bakar Aziz, Muhammad Amirul Solihin Azha, Saifful Kamaluddin Muzakir

Makara Journal of Technology

Dextran polymer host was doped with different concentrations of ammonium fluoride (NH4F) via casting technique. In this present work, dextran-NH4F film has been employed to investigate the ionic conductivity using electrochemical impedance spectroscopy from 50 to 5 MHz. The highest room temperature conductivity is achieved at (2.33 ± 0.76) × 10-3 S cm-1 with 40 wt.% NH4F. The electrolyte is found to obey Arrhenius rule at high temperature with activation energy of 0.21 eV. Dielectric analysis has been performed to obtain better understanding on the conductivity pattern. The dielectric parameters e.g. ɛreal, ɛimag, Mreal, and Mimag have been tested as …

Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman

Makara Journal of Technology

Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani

Makara Journal of Technology

Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …

Evaluation Of Fracture Principles In Asphalt Concrete Utilizing The Sc(B) Geometry, Airam Marlee Morales Vega

Graduate Theses and Dissertations

Since cracking is one of the principal distresses to be considered in asphalt concrete, multiple fracture tests and geometries have been used to quantify cracking resistance. One of the most popular geometries that have been used in fracture tests is the Semi-Circular bend (SC(B)). However, for this geometry, most of the fracture test methods use different parameters such as thickness, testing temperatures, and loading rates. Thus, the purpose of this research was first to evaluate fracture energy by performing a ruggedness test based on ASTM E1169. Then, to apply fracture mechanics concepts to evaluate three specimen thicknesses (25, 50, and …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …